HP 6600/HSR6800 Routers
AC1200 & DC1200 Power Modules
5998-2261
Part number: 5998-2261
Document version: 6PW101-20140307

Advertising

   Summary of Contents for HP HP 6600

  • Page 1: User Guide

    HP 6600/HSR6800 Routers AC1200 & DC1200 Power Modules User Guide 5998-2261 Part number: 5998-2261 Document version: 6PW101-20140307...

  • Page 2

    The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3: Table Of Contents

    Remove the DC power cords ························································· 18   Remove the DC power module ······················································ 19   Support and other resources ································································ 21   Contacting HP ·················································································· 21   Subscription service ··································································· 21   Related information ········································································· 22   Documents ·················································································· 22  ...

  • Page 4: Power Module Overview

    Power module overview In the following tabel, "Yes" means "Supported" and "No" means "Not supported." Product Power 6600 HSR6600 HSR6800 number module JG335A PSR1200-A JG334A PSR1200-D The PSR1200-A is a built-in power module with AC input and DC output, and the PSR1200-D is a built-in power module with DC input and DC output.

  • Page 5: Front Panel

    Front panel Figure 1 Front panel of PSR1200-A (1) Status LED (2) Power module handle (3) Captive screw (4) Power switch (5) Power socket...

  • Page 6

    Figure 2 Front panel of PSR1200-D (1) Power source connector (2) Status LED (3) Power module handle (4) Captive screw (5) Power switch (6) Fastening screw hole (7) Positive (+) terminal of DC input (8) Negative (–) terminal of DC input...

  • Page 7: Technical Specifications, Status Led

    Technical specifications Table 1 Technical specifications for the PSR1200-A and PSR1200-D Item PSR1200-A PSR1200-D 100 to 240 VAC –48 VDC to Rated input voltage (50/60 Hz) –60 VDC Rated output voltage 12 V and 3.3 V Maximum input current 16 A 42 A 100 A (12 V AC) •...

  • Page 8

    Table 2 Description of LEDs on the PSR1200-A and PSR1200-D Color/status Meaning Possible causes The power Green module is — operational. Power alarm (input under-voltage, output short circuit, output over-current, output over-voltage, or overheat occurred to the The power power module, and the module is faulty.

  • Page 9

    CAUTION: When the status LED is red, check whether the power module has • encountered the following failures: output short circuit, output over-current, output over-voltage, or overheat. If you have detected and removed the output short circuit, output over-current, or overheat failures, the power module automatically restores. However, if the power module encounters the output over-voltage failures, the power module will enter the deadlock sate, and cannot automatically restore after you remove the failures.

  • Page 10: Power Module Configuration

    Power module configuration You can determine the number of power modules to be configured for the system according to the actual power consumption and power supply conditions. In an environment with two power sources, you can configure • N+N redundant mode. In an environment with only one power source, you can configure •...

  • Page 11: Installing A Power Module

    Installing a power module CAUTION: PSR1200-A and PSR1200-D cannot work with other models of • power modules in the same device, and the PSR1200-A and PSR1200-D cannot work together in the same device. When the temperature of the power module is higher than the •...

  • Page 12

    Figure 3 Installation flow of a power module NOTE: The device needs at least one power module to provide power supply, so the chassis has a power module slot without a blank panel. For this slot, you can skip “Remove the blank panel” in the figure above.

  • Page 13: Installing The Ac Power Module

    #1 Phillips screwdriver cable tie ESD-preventive wrist strap Marker Installing an AC power module and connecting the power cord Installing the AC power module Follow these steps to install the AC power module: Wear an ESD-preventive wrist strap, and make sure that the wrist strap makes good skin contact and is properly grounded.

  • Page 14

    Figure 4 Remove the blank panel Unpack the power module. Put the power module to the correct position. Holding the power module handle with one hand and supporting the power module bottom with the other hand, plug the power module into the slot along the slide rails.

  • Page 15: Connecting The Ac Power Cord

    Connecting the AC power cord WARNING! Make sure that each power cord has a separate circuit breaker. • Turn off the circuit breaker before connecting the power cord. • Follow these steps to connect the AC power cord: Make sure the power switch is in the OFF position. Plug one end of the power cable shipped with the device into the power socket.

  • Page 16: Installing A Dc Power Module And Connecting The Power Cord

    Installing a DC power module and connecting the power cord Installing a DC power module Follow these steps to install a DC power module: Wear an ESD-preventive wrist strap, and make sure that the wrist strap makes good skin contact and is properly grounded. Use the Phillips screwdriver to loosen the captive screws on the blank panel, and remove the blank panel from the slot to be used, as shown in...

  • Page 17: Connecting The Dc Power Cords

    Put the power module to the correct position. Holding the power module handle with one hand and supporting the power module bottom with the other hand, plug the power module into the slot along the slide rails. Use the Phillips screwdriver to fasten the captive screws on the power module until the power module is fixed to the chassis.

  • Page 18

    Plug one end of the shipped DC power cord marked with “+”, a black power cord, into the terminal marked with “+”, and fasten the screw to fix the cord. Figure 10 Connect the DC power cords to the power source connector Put the power source connector to a correct position, plug the power source connector into the DC power module, and use the Philips screwdriver to fasten the captive screw at the right side to...

  • Page 19

    Plug the other end into the DC power source, and turn on the circuit breaker of the power cord. Turn on the power switch, and check that the status LED is ON. It indicates that the power cord is correctly connected. If the status LED is OFF, troubleshoot the installation process until the status LED is ON.

  • Page 20: Replacing A Power Module

    Replacing a power module Figure 12 illustrates the flow for replacing a power module. Strictly follow the sequence to avoid possible dangers. Figure 12 Replacement flow of a power module Before replacing a power module, prepare an ESD-preventive wrist strap and a #1 Phillips screwdriver. Remove the AC power cord Follow these steps to remove the AC power cord:...

  • Page 21: Remove The Dc Power Cords

    Wear an ESD-preventive wrist strap, and make sure that the wrist strap makes good skin contact and is properly grounded. Turn off the power switch. Turn off the circuit breaker of the power cord. Loosen the cable tie that fixes the power cord to the power module handle, and unplug the AC power cord connector.

  • Page 22: Remove The Dc Power Module

    Figure 13 Remove the DC power cords Remove the DC power module Follow these steps to remove the DC power module: Use the Phillips screwdriver to loosen the captive screws on the power module. Grasping the handle of the power module with one hand, pull the power module part way out.

  • Page 23

    Figure 14 Remove the DC power module Put the power module on an antistatic mat. Plug a new DC power module into the slot, and use the Philips screwdriver to fasten the captive screws on both sides of the power module. CAUTION: Before plugging a removed power module into a power module slot, make sure that the LED on the power module is off.

  • Page 24: Support And Other Resources, Subscription Service

    Operating system type and revision level • Detailed questions • Subscription service HP recommends that you register your product at the Subscriber's Choice for Business website: http://www.hp.com/go/wwalerts After registering, you will receive email notification of product enhancements, new driver versions, firmware updates, and other...

  • Page 25: Related Information

    Related information Documents To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals For related documentation, navigate to the Networking section, • and select a networking category. For a complete list of acronyms and their definitions, see HP •...

  • Page 26

    Command conventions Convention Description Bold text represents commands and keywords Boldface that you enter literally as shown. Italic text represents arguments that you Italic replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax { x | y | ...

  • Page 27

    GUI conventions Convention Description Window names, button names, field names, Boldface and menu items are in bold text. For example, the New User window appears; click OK. Multi-level menus are separated by angle > brackets. For example, File > Create > Folder. Symbols Convention Description...

  • Page 28

    Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.

This manual also for:

Hsr6800

Comments to this Manuals

Symbols: 0
Latest comments: