YASKAWA L1000A Technical Manual page 363

No. (Addr.) Name
n5-03
Inertia Compensation Gain
(5B2H)
n5-07 Speed Feedback Compensation
(170H) Selection
n5-08 Speed Feedback Compensation
(171H) Gain (P)
<4> Default setting value is dependent on the drive model (o2-04).
■
n6: Online Tuning
No. (Addr.) Name
n6-01
Online Tuning Selection
(570H)
n6-05
Online Tuning Gain
(5C7H)
■
n8: PM Motor Control Tuning
No. (Addr.) Name
n8-01
Initial Polarity Estimation Current
(540H)
n8-02
Pole Attraction Current
(541H)
n8-29 q-Axis Current Control Gain
(55CH) during Normal Operation
n8-30 q-Axis Current Control Integral
(55DH) Time during Normal Operation
n8-32 d-Axis Current Control Gain
(55FH) during Normal Operation
n8-33 d-Axis Current Control Integral
(560H) Time during Normal Operation
n8-35 Initial Rotor Position Detection
(562H) Selection
n8-36
High Frequency Injection Level
(563H)
n8-37 High Frequency Injection
(564H) Amplitude
n8-62
Output Voltage Limit
(57DH)
n8-81 High Frequency Injection during
(2D0H) Rescue Operation
High Frequency Injection
n8-82
Amplitude during Rescue
(2D1H)
Operation
YASKAWA ELECTRIC SIEP C710616 38A YASKAWA AC Drive L1000A Technical Manual
Description
V/f OLV
Sets the ratio between motor and load inertia. Lower this setting if overshoot occurs at the end
of acceleration.
V/f OLV
0: Disabled
1: Enabled
2: Test Mode
V/f OLV
Sets the proportional gain for the Speed Feedback Compensation.
Description
V/f OLV
0: Disabled
1: Line-to-line resistance tuning
2: Voltage correction.
V/f OLV
Decrease this setting for motors with a relatively large rotor time constant.
If overload occurs, increase this setting slowly in increments of 0.1.
Description
V/f OLV
Sets the current used for initial rotor position estimation as a percentage of the motor rated
current (E5-03). If the motor nameplate lists an "Si" value, that value should be entered here.
V/f OLV
Sets the current during initial polar attraction as a percentage of the motor rated current. Enter a
high value when attempting to increase starting torque.
V/f OLV
Sets the q axis proportional gain for the normal control range.
V/f OLV
Sets the q axis integral time for the normal control range.
V/f OLV
Sets the d axis proportional gain for the normal control range.
V/f OLV
Sets the d axis integral time for the normal control range.
V/f OLV
1: High frequency injection
2: Pulse injection
V/f OLV
Sets the frequency in Hz for the superimposed signal used for superimposed harmonics.
V/f OLV
Sets the amplitude for superimposed harmonics according to the voltage class of the motor.
Adjust this value when there is too much or too little current as a result of the settings assigned
to motor parameters.
V/f OLV
Prevents output voltage saturation. Should be set just below the voltage provided by the input
power supply.
V/f OLV
Sets the frequency used for Polar Detection Method 1 during Rescue Operation.
V/f OLV
Sets the amplitude for High Frequency Injection during Rescue Operation as a percentage of the
voltage (200 V or 400 V).
CLV CLV/PM
CLV/PM
CLV
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
B.3 Parameter Table
Setting Page
common_
Default: 1.00
TMonly
Min: 0.00 219
Max: 100.00
common_
TMonly
Default: 1
Min: 0 220
Max: 2
common_ Default: 12.00
TMonly
Min: 0.00 220
Max: 300.00
Setting Page
common_
TMonly
Default: 2
Min: 0 220
Max: 2
common_
Default: 1.0
TMonly
Min: 0.1 220
Max: 50.0
Setting Page
common_
Default: 50%
TMonly
Min: 0% 221
Max: 100%
common_
Default: 80%
TMonly
Min: 0% 221
Max: 150%
common_ Default: 1000 rad/s
TMonly
Min: 0 rad/s 222
Max: 2000 rad/s
common_ Default: 10.0 ms
TMonly
Min: 0.0 ms 223
Max: 100.0 ms
common_ Default: 1000 rad/s
TMonly
Min: 0 rad/s 223
Max: 2000 rad/s
common_ Default: 10.0 ms
TMonly
Min: 0.0 ms 223
Max: 100.0 ms
common_
Default: 1
TMonly
Min: 1 221
Max: 2
common_ Default: 500 Hz
TMonly
Min: 25 Hz 221
Max: 1000 Hz
common_
TMonly
Default: 20.0%
Min: 0.0% 222
Max: 99.9%
common_
Default: 200.0 V <9>
TMonly
Min: 0.0 V 223
Max: 230.0 V
<9>
common_ Default: 90 Hz
TMonly
Min: 25 Hz 222
Max: 1000 Hz
common_
Default: 15.0%
TMonly
Min: 0.1% 222
Max: 99.9%
B
363