Buzzer Menu (Audible Key Tones And Alarms) - Sanwa M12S SUPER User Manual

M12S SUPER
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
ASSIGN MENU { SWITCH, DIAL, LEVER AND TELEMETRY FUNCTION ASSIGNMENTS }
Changing the Telemetry Lever Control Function and Tweak Values, Continued:
For example, if you Assign AUX2 to the Telemetry Lever and adjust the Tweak values to +50 and -50, the Auxiliary 2 servo will be
centered when the Lever on your external device is centered and will travel 50% in one direction when the Lever on your external
device is moved Up and travel 50% in the other direction when the Lever on your external device is moved Down. Alternately, if you
Assign TRIM to the Telemetry Lever and adjust the Tweak values to +50 and -50, the Lever on your external device will control
ST
Steering Trim from 0% to 50%.
4) From within the TELEMETRY > LEVER menu, scroll UP or DOWN to highlight either T1 [TWEAK (H)] > +100 or T2 [TWEAK
(H)] > +100.
5) Press the ENTER key, then scroll UP or DOWN to choose the desired High Side Tweak value. Increasing the Tweak value will
Increase travel in the High Side direction and Decreasing the Tweak value will Decrease travel in the High Side direction.
Using a Negative value will change the direction of travel.
T1 TWEAK (H) and T2 TWEAK (H) setting range is -100 to +100. The default setting for both is +100.
6) Scroll UP or DOWN to highlight either T1 [TWEAK (L)] > -100 or T2 [TWEAK
(L)] > -100.
7) Press the ENTER key, then scroll UP or DOWN to choose the desired Low Side
Tweak value. Decreasing the Tweak value will Increase travel in the Low
Side direction and Increasing the Tweak value will Decrease travel in the
Low Side direction. Using a Positive value will change the direction of travel.
T1 TWEAK (L) and T2 TWEAK (L) setting range is -100 to +100. The default setting for both is -100.
BUZZER MENU { AUDIBLE KEY TONES AND ALARMS }
The Buzzer function allows you to change the Tone and Volume of many of the audible sounds that the transmitter makes. This
ranges from sounds that are made when you press the Trim Switches and Push-Button Switches, scroll UP or DOWN or press the
ENTER key, Lap and Interval Timer alarms, Telemetry Alert alarms, transmitter Voltage Limit alarm and more.
The Volume can be Increased or Decreased (or Muted) and the Tones can be changed to suit your preference. In addition,
different Tones can be set separately for the first half and the second half of a Tone, making it easier to differentiate between
the two halves.
The table below shows the functions that the Tone and Volume can be adjusted for:
FUNCTION
CLICK Controls Key Press Tones, Such as ENTER, BACK, SELECT and All Push-Button Switches
TRIM Controls All Trim Switch Key Press Tones
CENTER Controls the Trim Switch, Auxiliary Dial and Auxiliary Lever Neutral Point Indicator Tones
MULTI Controls the Push-Button Rotary Dial scroll UP and Scroll DOWN Tones
TIMER SW Controls the Lap Timer Start and Stop Tones
INT1 TIMER Controls the First Interval Timer Start and Stop Tones
INT2 TIMER Controls the Second Interval Timer Start and Stop Tones
LAP-PRE Controls the Lap Timer Pre-Alarm Tones
LAP GOAL Controls the Lap Timer Goal Alarm Tones
DOWN-PRE Controls the Countdown Timer Pre-Alarm Tones
DOWN-FIN Controls the Countdown Timer Final Alarm Tones
UP-1MIN Controls the 1 Minute Count Up Timer Alarm Tones
OFFSET Controls the Offset Function Alarm Tones
TLM VOLT Controls the Telemetry Receiver Voltage Alert Alarm Tones
TLM1 Controls the Telemetry 1 (Default Temp 1) Alert Alarm Tones
TLM2 Controls the Telemetry 2 (Default Temp 2) Alert Alarm Tones
LIMIT Controls the Transmitter Limit Voltage Alarm Tones
46
Telemetry System with Sanwa Synchronized Link Support
DESCRIPTION
SYSTEM
SYSTEM