Table of Contents
Advertisement
M12S SUPER
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
OPTIONAL STEERING WHEEL ANGLE PLATE INSTALLATION
Two optional Steering Wheel Angle Plates (one Right and one Left) are included that changes the angle of the Steering Wheel and
Trim Switch Ring. Some users may find that angling the Steering Wheel to the Right or Left may be more comfortable during use.
'R' and 'L' are molded into the Angle Plates to differentiate them. The 'R' Angle Plate will angle the Steering Wheel toward the
Right and the 'L' Angle Plate will angle the Steering Wheel toward the Left.
To install the Right or Left Steering Wheel Angle Plate, follow the steps below:
1) Use a 7mm nut driver to remove the Steering Wheel Retaining Nut (A), then pull the Steering
Wheel (B) and the Steering Wheel Adapter (C) straight off and set them aside.
2) Using a Philips head screwdriver, remove the three M3 x 20mm tapping screws (D), then carefully
pull the Trim Switch Ring (E) off the transmitter and very carefully unplug the two connectors.
Installation Without Steering Wheel Offset Plate:
The installation procedures below outline installing either Angle Plate without the
optional Steering Wheel Offset Plate described in the previous sections. Complete
steps 1 and 2 above before proceeding.
D
C
B
A
Installation With Steering Wheel Offset Plate:
The installation procedures below outline installing either Angle Plate along with the optional Steering
Wheel Offset Plate described in the Steering Wheel Offset Plate Installation section on the previous page.
1) Complete steps 1 and 2 above to remove the Steering Wheel, Steering Wheel Adapter and the
Trim Switch Ring.
2) Choose which Angle Plate you want to install, then feed the connectors from the Trim Switch Ring
through the Angle Plate and on through the center hole in the Steering Wheel Offset Plate.
3) Install the Steering Wheel Offset Plate (G) to the transmitter at the
desired angle, using four M3 x 8mm tapping screws (H) included. Refer
to the drawing on the previous page for Steering Wheel Offset Plate
mounting options.
The Trim Switch Ring and Angle Plate must be left loose so you
can install the two lower tapping screws.
4) Place the Bracket Cover (F) in place, then install
the Angle Plate (J) onto the Steering Wheel Offset
Bracket, using three M3 x 8mm tapping screws (K).
5) Install the Trim Switch Ring (E) onto the Angle Plate (K), using the three M3 x 20mm tapping screws (D) you removed previously.
6) Reinstall the Steering Wheel Adapter (C) and the Steering Wheel (B), and secure them in place using the Steering Wheel
Retaining Nut (A). Installation is the reverse of removal.
Telemetry System with Sanwa Synchronized Link Support
K
J
4) Very carefully plug the connectors from the Trim Switch Ring into the
5) Being careful not to pinch any wires, align and secure the Trim Switch Ring to the Angle
Plate using the three M3 x 20mm tapping screws (D) you removed previously.
E
6) Reinstall the Steering Wheel Adapter (C) and the Steering Wheel (B), and secure them in
place using the Steering Wheel Retaining Nut (A). Installation is the reverse of removal.
3) Choose which Angle Plate you want to install, then align and
secure the Angle Plate (J) to the transmitter, using three M3 x 8mm
tapping screws (K) included. There are small notches in both the
Trim Switch Ring and the Angle Plate that line up with corresponding
small tabs in the Angle Plate and the transmitter to ensure both
the Trim Switch Ring and the Angle Plate are installed in the correct
orientation.
matching connectors in the transmitter.
D
A
C
B
D
A
C
B
F
K
E
T
GENERAL
E
J
15
Advertisement
Table of Contents
