Table of Contents
Advertisement
M12S SUPER
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
ASSIGN MENU { SWITCH, DIAL, LEVER AND TELEMETRY FUNCTION ASSIGNMENTS }
Changing the Telemetry Trim Switch Control Function, Step and Reverse Values, Continued:
A multitude of different functions can be Assigned to the Telemetry Trim Switch. In addition, the Step value and Direction of Travel
can be changed to allow you to adjust how far a servo travels or how far a function moves and the direction it moves to suit both
the programmed function and the specific requirements of your external device.
1) From within the TELEMETRY > TRIM menu, scroll UP or DOWN to highlight
T1/T2 [FUNCTION] > - - -.
2) Press the ENTER key, then scroll UP or DOWN to choose the desired function
for the Telemetry Trim Switch.
A list of functions that can be Assigned to the Telemetry Trim Switch is
shown in the Trim Switch, Auxiliary Dial and Auxiliary Lever Functions
tables on pages 114 and 115.
How far a servo travel or how far a function moves when the Telemetry Trim Switch on your external device is pressed can be
changed. You can Increase the Resolution by Decreasing the Step value, so that the amount of servo travel or function movement
is less when you press the Telemetry Trim Switch. This makes it possible to fine-tune servo travel or function movement extremely
accurately. Alternately, you could Decrease the Resolution by Increasing the Step value, so that the amount of servo travel or
function movement is more when you press the Telemetry Trim Switch. This may not be as accurate, but it allows you to command
large amounts of servo travel or function movement at a time.
3) From within the TELEMETRY > TRIM menu, scroll UP or DOWN to highlight
T1/T2 [STEP] > 1.
4) Press the ENTER key, then scroll UP or DOWN to change the desired Telemetry
Trim Switch Step value.
STEP setting range is 1 to 100. The default setting is 1. The Step value is a
percentage of travel.
The direction that the Telemetry Trim Switch moves the servo or function can be changed from Normal to Reverse to suit the
programmed function and the specific requirements of your external device.
5) From within the TELEMETRY > TRIM menu, scroll UP or DOWN to highlight
T1/T2 [REV] > NOR.
6) Press the ENTER key, then scroll UP or DOWN to choose the desired Telemetry
Trim Switch Reverse value.
REV setting range is NOR and REV. The default setting is NOR.
Changing the Telemetry Lever Control Function and Tweak Values:
Follow the information in this section if you've programmed the Telemetry value to LEVER. If you've programmed the Telemetry
value to SW or TRIM, please refer to those specific sections.
A multitude of different functions can be Assigned to the Telemetry Lever. Up to two different functions can be Assigned to each
Telemetry Lever (T1 and T2) and the High and Low Tweak values can be adjusted to customize how far and in which direction
the Telemetry Lever controls the servo or function to suit both the programmed function and the specific requirements of your
external device.
1) From within the TELEMETRY > LEVER menu, scroll UP or DOWN to highlight the
Telemetry Lever Number and Function you would like to change. Choose from
T1 [FUNCTION] or T2 [FUNCTION].
2) Press the ENTER key, then scroll UP or DOWN to choose the desired function
for the Telemetry Lever Number and Function you highlighted.
A list of functions that can be Assigned to the Telemetry Lever is shown
in the Trim Switch, Auxiliary Dial and Auxiliary Lever Functions tables on
pages 114 and 115.
3) Press the ENTER key, then repeat steps 1 and 2 to program any other desired Telemetry Lever Function Assignments.
The High and Low Tweak values both determine how far and in which direction the servo travels or the function moves when the
Lever on your external device is moved, regardless if the Telemetry Lever is controlling a servo, such as Auxiliary Channel 2 or
a function, such as Steering Trim.
Telemetry System with Sanwa Synchronized Link Support
T
SYSTEM
45
Advertisement
Table of Contents
