Changing The Trim Switch Step Value; Changing The Trim Switch Direction Of Travel - Sanwa M12S SUPER User Manual

M12S SUPER
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
ASSIGN MENU { SWITCH, DIAL, LEVER AND TELEMETRY FUNCTION ASSIGNMENTS }
Changing the Trim Switch Function Assignments, Continued:
4) Scroll UP or DOWN to highlight the Trim Switch Number you would like to
change. Choose from TRM1, TRM2, TRM3, TRM4 or TRM5.
5) Press the ENTER key, then scroll UP or DOWN to choose the desired function
for the Trim Switch Number you highlighted.
6) Press the ENTER key, then repeat steps 4 and 5 to program any other desired Trim Switch Function Assignments.
The table below shows the default Trim Switch functions based on the Selected Car Type. A complete list of functions that can be Assigned to
the Trim Switches are shown in the Trim Switch, Auxiliary Dial and Auxiliary Lever Functions tables on pages 114 and 115.
Model Type TYP I
TRM1 TRIM ST
TRM2 TRIM TH
TRM3 D/R ST
TRM4 R-MODE
TRM5 D/R BR

Changing the Trim Switch Step Value:

The Step function allows you to adjust how far a servo travels or a function moves when a Trim Switch is pressed. You can
Increase the Trim Resolution by Decreasing the Step value, so that the amount of travel is less when you press the Trim Switches.
This makes it possible to fine-tune travel extremely accurately.
Alternately, you could Decrease the Trim Resolution by Increasing the Step value, so that the amount of travel is more when you
press the Trim Switches. This may not be as accurate, but it allows you to command large amounts of travel or function
movement at a time.
1) From within the TRIM menu, scroll UP or DOWN to highlight the Trim Switch
Number [STEP] you would like to change. Choose from TRM1 [STEP],
TRM2 [STEP], TRM3 [STEP], TRM4 [STEP] or TRM5 [STEP].
2) Press the ENTER key, then scroll UP or DOWN to change the desired Trim
Switch Step value.
STEP setting range is 1 to 100. The default setting is 1 or 5 depending on the
Trim Switch Number. The Step value is a percentage of travel.
3) Repeat step 2 to change any other desired Trim Step values.

Changing the Trim Switch Direction of Travel:

The direction that the Trim Switches move the servos or function values can be changed from Normal to Reverse. In Normal mode,
the Trim Switches will move the servos toward the High Side or Increase function values when the Trim Switches are pushed
Forward. In Reverse mode, the Trim Switches will move the servos toward the Low Side or Decrease function values when the
Trim Switches are pushed Forward.
1) From within the TRIM menu, scroll UP or DOWN to highlight the Trim Switch
Number [REV] you would like to change. Choose from TRM1 [REV],
TRM2 [REV], TRM3 [REV], TRM4 [REV] or TRM5 [REV].
40
Telemetry System with Sanwa Synchronized Link Support
TYP II TYP III TYP IV
TRIM ST TRIM ST TRIM ST
TRIM TH TRIM TH TRIM TH
D/R ST D/R ST D/R ST
R-MODE R-MODE R-MODE
D/R BR D/R BR D/R BR
TYP V TYP VI TYP VII
TRIM ST TRIM ST TRIM ST
TRIM TH TRIM TH TRIM TH
D/R ST D/R ST D/R ST
R-MODE R-MODE R-MODE
D/R BR D/R BR D/R BR
SYSTEM
TYP VIII TYP IX TYP X
TRIM ST TRIM ST TRIM ST
TRIM TH TRIM TH TRIM TH
D/R ST D/R ST D/R ST
R-MODE R-MODE R-MODE
D/R BR D/R BR D/R BR