Table of Contents
Advertisement
M12S SUPER
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
PROBLEM
Transmitter does not control model
Servo(s) and/or ESC don't operate at all or
operate erratically
Direction of travel shown on Servo Monitor is
different from control input travel
Can't control underscore when changing Model
Name,User Name etc
Telemetry Data doesn't record when Lap Timer
is Started
Can't clear Lap Timer
Steering Wheel and/or Throttle Trigger won't
center
Steering Wheel, Throttle Trigger and/or Auxiliary
Lever controls not centered or otherwise not
working as expected
Unable to program the Code Aux function
Cannot Name or rename Model Templates
Telemetry Assign function does not work
Transmitter vibrates under certain conditions
Can't turn C-Mixes and/or T-Mixes ON or OFF
during use
Some functions, such as OFFSET and TH-HOLD
not functioning
RACING MODE FUNCTIONS BY CAR TYPE
The tables below and on the next page shows the available Racing Mode functions by Car Type and channel.
TYPE
TYP I
FUNCTION
CH1
ST
CH2
TH/BR
D/R
CH3
----
CH4
----
CH1
ST
CH2
TH
TRIM
CH3
AUX1
CH4
AUX2
CH1
ST
CH2
TH/BR
CURVE
CH3
AUX1
CH4
AUX2
CH1
ST
CH2
TH/BR
SPEED
CH3
AUX1
CH4
AUX1
Telemetry System with Sanwa Synchronized Link Support
CAUSE
Safety Link Number doesn't match
selected model
No RF Signal from transmitter
Transmitter in RECEIVER Mode
Using incorrect Channel Response
Mode setting
This is normal
Cursor is Active in Character Select
screen
Telemetry Data Recording function
turned OFF
Telemetry system turned OFF
This is normal
Spring tension set too loose
Controls require Calibration
Selected Car Type doesn't support a free
AUX channel (e.g. Car Type X)
This is normal
Telemetry system turned OFF
External device not paired
External device not compatible
Not using compatible receiver
Vibration Alerts turned ON
C-Mixes and/or T-Mixes not Assigned to
different Racing Modes
Function not Assigned to a Push-Button
Switch
TYP II
TYP III
TYP IV
ST
ST
ST
TH
TH/BR
TH
BR
BR2
BR
----
----
BR2
ST
ST
ST
TH
TH
TH
BR
BR2
BR
AUX
AUX
BR2
ST
ST
ST
TH
TH/BR
TH
BR
BR2
BR
AUX
AUX
BR2
ST
ST
ST
TH
TH/BR
TH
BR
BR2
BR
AUX
AUX
BR2
Choose correct model that matches receiver or Bind
model again with correct Safety Link Number
Transmitter is in DISPLAY Mode and not actually
turned ON
Turn DISPLAY Mode OFF, then turn transmitter ON
Use correct Channel Response Mode setting based
on the type of servos and/or ESC you're using
Direction of travel displayed will vary depending on
Servo Reversing settings
Press BACK key to re-gain control of underscore
Turn Telemetry Data Recording function ON
Turn Telemetry system ON
Lap Timer will clear when you Start the Lap Timer again
Tighten spring tension
Calibrate control End Points and Neutral positions
using Calibration function
Select a Car Type that features one or more free AUX
channels
Model Templates are saved using the current Model
Name
Turn Telemetry system ON
Pair external device to system
Use compatible Airtronics or Sanwa external device
Use Airtronics or Sanwa 2.4GHz FH4T receiver
Turn Vibration function OFF for the desired Alerts
Assign one C-Mix or T-Mix with desired Rate values
to one Racing Mode and another C-Mix or T-Mix with
0% Rate values to a different Racing Mode. Switch
between the two Racing Modes to the turn the Mixes
ON (one with Rate values) and OFF (one without).
These types of functions must be Assigned to a
Push-Button Switch to be turned ON and OFF.
TYP V
TYP VI
TYP VII
ST
ST
ST
TH/BR
TH
TH/BR
ST
ST
ST
----
BR
BR2
ST
ST
ST
TH
TH
TH
ST
ST
ST
AUX
BR
BR2
ST
ST
ST
TH/BR
TH
TH/BR
ST
ST
ST
AUX
BR
BR2
ST
ST
ST
TH/BR
TH
TH/BR
ST
ST
ST
AUX
BR
BR2
SOLUTION
REFERENCE
TYP VIII
TYP IX
TYP X
ST
ST
ST
TH/BR
TH/BR
TH/BR
ST
----
ST
----
----
----
ST
ST
ST
TH
F/TH
F/TH
ST
R/TH
ST
AUX
AUX
R/TH
ST
ST
ST
TH/BR
TH/BR
TH/BR
ST
TH/BR
ST
AUX
AUX
TH/BR
ST
ST
ST
TH/BR
TH/BR
TH/BR
ST
TH/BR
ST
AUX
AUX
TH/BR
113
T
Advertisement
Table of Contents
