Reviewing Telemetry Data - Sanwa M12S SUPER User Manual

M12S SUPER
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
TELEMETRY SCREEN OVERVIEW
TELEMETRY Screen Overview Diagram Descriptions, Continued:
Numerical Telemetry Data: Displays the Telemetry Data in a numerical format.
Page Indicator: Indicates the current Page within the Telemetry Data Stream that Telemetry Data is currently being displayed on.
Receiver Voltage Display: Displays the current Voltage of the receiver battery. The tick mark indicates the current Voltage relative
to the programmed Maximum Voltage value.
RPM/Speed Display: Displays the current RPM or speed in MPH or KM/H.
RPM/Speed Gauge: Displays the current RPM or speed in MPH or KM/H in graphical format. The needle indicates the
current RPM or Speed relative to the programmed Maximum RPM or Speed value.
Status Indicator: Indicates the current Status of the Telemetry system. When VIEW is displayed, the Telemetry system is in VIEW
mode, allowing you to view and analyze Telemetry Data. When REC is displayed, the Telemetry system is Recording Telemetry
Data. When LOG is displayed, the Telemetry system is in Standby.
Steering Output Display: Displays the current position of the Steering channel as a percentage of Steering Wheel travel.
Telemetry Data Graph: Displays the Telemetry Data Stream in a graphical format.
Temperature 1 Display: In the default configuration, displays the current temperature in Fahrenheit or Celsius of the Temperature
Sensor plugged into the TEMP1 Sensor Port in the receiver. The tick mark indicates the current temperature relative to the
programmed Maximum and Minimum Temperature values. This label can be changed if using different Telemetry accessories.
Temperature 2 Display: In the default configuration, displays the current temperature in Fahrenheit or Celsius of the Temperature
Sensor plugged into the TEMP2 Sensor Port in the receiver. The tick mark indicates the current temperature relative to the
programmed Maximum and Minimum Temperature values. This label can be changed if using different Telemetry accessories.
Throttle Output Display: Displays the current position of the Throttle channel as a percentage of Throttle Trigger travel.

Reviewing Telemetry Data:

When the Telemetry Data Recorder has Stopped, you are able to view Telemetry Data in more detail. For more information about
Starting and Stopping the Telemetry Data Recorder, see the Telemetry Data Recording section on pages 56 and 57.
1) After Stopping the Telemetry Data Recorder, press the SELECT switch to open the desired TELEMETRY page, either ST, TH,
RPM, VOLT TMP1 or TMP2.
2) Press the ENTER key. The VIEW menu will open and PAGE will be surrounded
by a box.
3) Scroll UP or DOWN to select the desired VIEW menu option.
CURSOR - When chosen, scrolls through the Telemetry Data Stream in 0.5
second intervals.
PAGE - When chosen, scrolls through the individual pages of the Telemetry Data
Stream.
LAP - When chosen, scrolls through each counted Lap Time along the Telemetry Data Stream.
LAP-LT - When chosen, displays Total, Best and Average Lap Times, in addition to individual Lap Times.
SAVE - When chosen, allows you to Save the Telemetry Data Log to your PC.
4) Press the ENTER key to highlight the desired VIEW menu option, then scroll
UP or DOWN to scroll through the Telemetry Data Stream via the VIEW
menu option you chose. You can also press the SELECT switch RIGHT or
LEFT to view different TELEMETRY pages.
If you choose the SAVE option to Save the Telemetry Data Log to your
PC, see the PC LINK Menu > Saving the Telemetry Data Log section
on pages 67 and 68 for information on how to do this.
5) To choose a different VIEW menu option, press the BACK key, then repeat steps 3 and 4 to choose and highlight the desired
VIEW menu option.
When viewing the Telemetry Data Stream using the VIEW option menu, keep these things in mind: When a VIEW menu
option is surrounded by a box, scroll UP or DOWN to choose a different VIEW menu option. When a VIEW menu option
is highlighted, scroll UP or DOWN to scroll through the Telemetry Data Stream. Press the BACK key to cancel the highlighted
VIEW menu option and choose another VIEW menu option.
As you're scrolling through the Telemetry Data Stream, press the ENTER key at any time to Open a detailed list of Telemetry
Data Entries. The highlighted Telemetry Data Entry at the top of the list is the one where you pressed the ENTER key.
22
Telemetry System with Sanwa Synchronized Link Support
GENERAL