Table of Contents
Advertisement
M12S SUPER
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
TRANSMITTER AND RECEIVER OVERVIEW DIAGRAM DESCRIPTIONS
Trim Switches: The transmitter features five separate Trim Switches - four positioned around the Steering Wheel (Trm1, Trm2,
Trm3 and Trm4 and one positioned below the Auxiliary Lever (Trm5). Each Trim Switch is programmable and will perform a different
function depending on what function is assigned to it. For example, Trm1 and Trm2 can be used to adjust Steering and Throttle
Trim and Trm4 and Trm5 can be used to adjust Dual Rate and Steering EPA.
Wrist Strap Anchor Slot: Used to attach the wrist strap anchor to the transmitter.
TRANSMITTER LED CONDITION INDICATORS AND WARNING ALARMS
The M12S Super is equipped with several different Audible Warning Alarms to warn you of an abnormal transmitter condition. In
addition, LED1, LED2 and the Response Mode LEDs and R-MODE LED are used to indicate various conditions at a glance.
LED Condition Indicators
LED1, LED2 and the Response Mode LEDs and R-MODE LED are used to indicate various transmitter conditions at a glance.
Some of the conditions indicated by the LEDs may also be accompanied by an audible alarm and/or and on-screen warning.
TRANSMITTER STATUS
Display Mode
RF Output Signal
Throttle Offset Function Active
Telemetry Logger Function Active
RF Binding - Sending Bind Code
PC LINK USB Send/Receive Active
Inactivity Alarm Active
Telemetry Alarm Active
Telemetry Connection Active
No Telemetry Connection
Low Voltage Alert Alarm Active
Low Voltage Limit Alarm Active
Over Voltage Alarm Active
Transmitter Error
Programming Data/Update Error
Unrecoverable Update Error
Racing Mode 1 Active
Racing Mode 2 Active
Racing Mode 3 Active
Racing Mode 4 Active
Racing Mode 5 Active
Racing Mode Function Inhibited
NOR Channel Response Mode
SHR Channel Response Mode
SSR Channel Response Mode
Audible Warning Alarms
The audible alarms listed below and on the next page may also be accompanied by an on-screen warning.
Inactivity (Power ON) Alarm:
The Inactivity Alarm will sound if the transmitter is left on for a period of 10 minutes without any control input from the user. This
alarm alerts you to prevent unwanted draining of the transmitter battery. To clear this alarm, either turn the transmitter OFF or
press the BACK key or the ENTER key.
Over Voltage Alarm:
The Over Voltage Alarm will sound if the transmitter battery voltage is greater than 9.6 volts. To clear this alarm, turn the transmitter
OFF and replace the transmitter battery with one that when fully charged does not exceed 9.6 volts.
10
Telemetry System with Sanwa Synchronized Link Support
LED1
OFF
ON
0.1 Sec. Flash
0.5 Sec. Flash
0.35 Sec. Flash
0.05 Sec. Flash
------
0.1 Sec. Flash
------
0.1 Sec. Flash
------
------
------
0.35 Sec. Flash
------
0.05 Sec. Flash
------
0.05 Sec. Flash
1 Sec. Flash
1 Sec. Flash
------
1 Sec. Flash
------
------
------
------
------
------
------
------
------
------
LED2
R-MODE LED
------
------
------
------
------
------
------
------
------
------
------
------
------
------
OFF
------
ON
------
------
------
------
OFF
OFF
------
OFF
------
Green
------
Magenta
Cyan
------
------
Yellow
------
White
------
OFF
------
------
------
------
------
------
GENERAL
GENERAL
ST R-MODE LED TH R-MODE LED
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
------
OFF
OFF
Red
Red
Blue
Blue
Advertisement
Table of Contents
