Mitsubishi Electric FR-F700PJ Instruction Manual page 240

Air-conditioning inverter
Hide thumbs Also See for FR-F700PJ:
Table of Contents

Advertisement

Example) When reading the C3 (Pr. 902) and C6 (Pr. 904) settings from the inverter of station 0
Computer Send Data
1)
ENQ 00 FF 0 01 82
2)
ENQ 00 EC 0 01 7E
3)
ENQ 00 5E 0 0F
4)
ENQ 00 60 0 FB
To read/write C3 (Pr. 902) and C6 (Pr. 904) after inverter reset or parameter clear, execute from 1) again.
 List of calibration parameters
Parameter
Name
C2 (902) Terminal 2 frequency setting bias frequency
C3 (902) Terminal 2 frequency setting bias
Terminal 2 frequency setting gain
125 (903)
frequency
C4 (903) Terminal 2 frequency setting gain
C5 (904) Terminal 4 frequency setting bias frequency
C6 (904) Terminal 4 frequency setting bias
Terminal 4 frequency setting gain
126 (905)
frequency
C7 (905) Terminal 4 frequency setting gain
[Special monitor selection No.]
Refer to page 152 for details of the monitor description.
Data
Description
Output frequency/speed/
H01
Machine speed 
H02
Output current
Output voltage/Machine speed 
H03
Frequency setting/speed setting/
H05
Machine speed
H08
Converter output voltage
H09
Regenerative brake duty
Electronic thermal relay function
H0A
load factor
H0B
Output current peak value
H0C
Converter output voltage peak value
H0E
Output power
H0F
Input terminal status
H10
Output terminal status
H14
Cumulative energization time
H17
Actual operation time

The data format is 6 digits (E2) when the following conditions are met: Pr.37 = "0.01 to 9998," Pr.144 = "2 to 10," and the instruction code HFF = "01."
(Refer to page 150 for Pr.37 and Pr.144.)

Input terminal monitor details (when the terminal is ON: 1, when the terminal is OFF: 0, —: undetermined value)
b15

Output terminal monitor details (when the terminal is ON: 1, when the terminal is OFF: 0, —: undetermined value)
b15

The monitored values are retrained even if an inverter fault occurs. Resetting will clear the retained values.
Inverter Send Data
ACK 00
Set "H01" to the extended link parameter.
ACK 00
Set "H01" to second parameter changing.
STX 00 0000 ETX 25
C3 (Pr. 902) is read. 0% is read.
STX 00 0000 ETX 25
C6 (Pr. 904) is read. 0% is read.
Instruction
Code
5E DE
5E DE
5F
DF
5F
DF
60
E0
60
E0
61
E1
61
E1
Unit
0.01Hz/
1/0.001
0.01A
0.1V
0.01Hz/
1/0.001
0.1V
0.1%
0.1%
0.01A
0.1V
0.01kW
1h
1h
Communication operation and setting
Description
Parameter
Frequency setting voltage bias frequency
1
C22(922)
(built-in potentiometer)
1
Frequency setting voltage bias (built-in
C23(922)
1
potentiometer)
Frequency setting voltage gain frequency
1
C24(923)
(built-in potentiometer)
1
Frequency setting voltage gain (built-in
1
C25(923)
potentiometer)
1
1
Data
Description
H18
Motor load factor
H19
Cumulative power
H32
Power saving effect
H33
Cumulative power saving
H34
PID set point
H35
PID measured value
H36
PID deviation
H3D
Motor thermal load factor
H3E
Inverter thermal load factor
H3F
Cumulative power 2
H40
PTC thermistor resistance
32-bit cumulative power
H4D
(lower 16-bit)
32-bit cumulative power
H4E
(upper 16-bit)
32-bit cumulative power
H4F
(lower 16-bit)
32-bit cumulative power
H50
(upper 16-bit)
RH
RM
ABC
Instruction
Code
Name
16
96
16
96
17
97
17
97
Unit
0.1%
1kWh
Variable
Variable
0.1%
0.1%
0.1%
0.1%
0.1%
0.01kWh
0.01k
1kWh
1kWh
0.01kWh
0.01kWh
AU
STR
9
9
9
9
4
b0
STF
b0
RUN
235

Advertisement

Table of Contents
loading

Table of Contents