Download  Print this page

Appendix 4 Index - Mitsubishi Electric FR-F700PJ Instruction Manual

Air-conditioning inverter.
Hide thumbs

Advertisement

Appendix 4 Index

Numerics
15-speed selection (REX signal) ................................... 106, 134
A
Acceleration time, deceleration time setting (Pr. 7, Pr. 8, Pr.
20, Pr. 21, Pr. 44, Pr. 45).................................................... 113
Acceleration/deceleration pattern (Pr. 29) ........................... 118
Actual operation time............................................................... 152
Adjusting the speed control gain (Pr.820, Pr.821)................ 90
Alarm output (LF signal) ................................. 140, 222, 238, 264
Analog input fault (E.AIE) ....................................................... 307
Analog input selection (Pr. 73, Pr. 267) ............................... 183
Applied motor (Pr. 71, Pr. 450).............................................. 123
Automatic restart after instantaneous power failure/flying start
(Pr. 30, Pr. 57, Pr. 58, Pr. 96, Pr. 162, Pr. 165, Pr. 298, Pr.
299, Pr. 611) ......................................................................... 161
Automatic restart after instantaneous power failure/flying start
under IPM motor control (Pr. 57, Pr. 162, Pr. 611)......... 166
Avoid mechanical resonance points (frequency jumps) (Pr. 31
to Pr. 36, Pr. 552)................................................................. 102
B
Base frequency, voltage (Pr. 3, Pr. 19, Pr. 47) ................... 103
Basic operation (factory setting).............................................. 59
Bias and gain of frequency setting voltage (current) (Pr. 125,
Pr. 126, Pr. 241, C2 (Pr. 902) to C7 (Pr. 905)) ............... 188
Bias and gain of the built-in frequency setting potentiometer
(C22 (Pr. 922) to C25 (Pr. 923))........................................ 284
Brake transistor alarm detection (E.BE)............................... 305
Built-in potentiometer switching (Pr. 146) ............................ 283
Buzzer control (Pr. 990).......................................................... 282
C
Cables and wiring length .......................................................... 22
Changing the control logic ........................................................ 27
Changing the parameter setting value ................................... 61
Checking the inverter and converter modules..................... 320
Cleaning .................................................................................... 320
Command source switchover (turning ON X67 makes Pr. 338
and Pr. 339 commands valid) (X67 signal).............. 134, 214
Communication EEPROM write selection (Pr. 342)........... 225
Condition selection of function validity by second function
selection signal (RT signal) ................................................ 137
Connection of a DC reactor (FR-HEL) ................................... 40
Connection of a dedicated external brake resistor (MRS type,
MYS type, FR-ABR) .............................................................. 34
Connection of the brake unit (FR-BU2).................................. 36
Connection of the high power factor converter (FR-HC) ..... 38
Connection of the power regeneration common converter
(FR-CV) ................................................................................... 39
Connection to the PU connector ............................................. 32
Control circuit terminal .............................................................. 25
Converter Output Voltage....................................................... 152
Converter output voltage peak value .................................... 152
Cooling fan operation selection (Pr. 244)............................. 264
Cooling system types for inverter panel ................................. 11
CPU fault (E.5, E.CPU)........................................................... 306
Cumulative energization time................................................. 152
Cumulative power .................................................................... 152
Current average value monitor signal (Pr. 555 to Pr. 557) 269
Current average value monitor signal (Y93 signal) .... 140, 269
D
Daily and periodic inspection ................................................. 319
Daily inspection ........................................................................ 318
DC injection brake (Pr. 10 to Pr. 12)..................................... 129
DC injection brake of IPM motor control (Pr.10, Pr.11)......130
Detection of output frequency
(SU, FU signal, Pr. 41 to Pr. 43) ........................................144
Display of the life of the inverter parts
(Pr. 255 to Pr. 259).......................................................265, 320
During PID control activated (PID signal) .....................140, 250
During retry (Y64 signal) .................................................140, 170
E
Earth (ground) fault detection at start (Pr. 249) ...................172
Easy operation mode setting (easy setting mode)................60
Electronic thermal O/L relay pre-alarm (THP signal)..119, 140
Electronic Thermal Relay Function Load Factor .................152
Electronic thermal relay function prealarm (TH)..........119, 300
EMC measures ...........................................................................45
Energy saving monitor (Pr. 891 to Pr. 899)..........................175
Exhibiting the best performance for the motor (offline auto
tuning) (Pr. 71, Pr. 80, Pr. 82 to Pr. 84, Pr. 90, Pr. 96) ..125
Extended parameter display (Pr. 160) ..................................197
External thermal relay input (OH signal).......................119, 134
External thermal relay operation (E.OHT) ....................119, 305
External/NET operation switchover (turning ON X66 selects
NET operation) (X66 signal) .......................................134, 208
F
Fan alarm (FN)..................................................................264, 301
Fan fault output (FAN signal)..........................................140, 264
Fault or alarm indication ..................................................152, 292
Fault output (ALM signal) ................................................140, 143
Fault output 3 (power-OFF signal) (Y91 signal) ..........140, 143
Faults history (E.---) .................................................................292
Fin overheat (E.FIN).................................................................304
Forward rotation command (assigned to STF terminal (Pr.
178) only) (STF signal) ................................................134, 138
Free parameter (Pr. 888, Pr. 889) .........................................271
Frequency setting signal (current) bias/gain adjustment
method ...................................................................................190
Frequency setting value ..................................................152, 157
Front cover.....................................................................................6
G
General-purpose magnetic flux vector control
(Pr. 71, Pr. 80).........................................................................93
H
Harmonic suppression guideline in Japan..............................48
Heatsink overheat pre-alarm (FIN signal).....................140, 304
High speed operation command (RH signal) ...............106, 134
How to calibrate the terminal FM when using the operation
panel .......................................................................................159
I
Initial settings and specifications of RS-485 communication
(Pr. 117 to Pr. 120, Pr. 123, Pr. 124, Pr. 549) .................221
Initializing the parameters required to drive an IPM motor
(Pr.998) ....................................................................................85
Initiating a fault (Pr.997) ..........................................................272
Input phase loss (E.ILF) ..................................................172, 304
Input terminal function selection (Pr. 178 to Pr. 182) .........134
Input Terminal Status...............................................................152
Input/output phase loss protection selection
(Pr. 251, Pr. 872) ..................................................................172
Inrush current limit circuit fault (E.IOH) .................................306
Installation of Filterpack.............................................................13
Installation of the inverter and Filterpack (for rear panel
installation)...............................................................................12
347

Advertisement

Table of Contents

   Also See for Mitsubishi Electric FR-F700PJ

Comments to this Manuals

Symbols: 0
Latest comments: