Mitsubishi Electric FR-F700PJ Instruction Manual page 239

Communication operation and setting
Item
Fault history batch
clear
Parameter clear
All clear
Parameter
Link parameter
extended setting
Second parameter
changing
(instruction code
HFF = 1, 9)
Multi command
Inverter
model
Capacity

Refer to page 227 for data format (A, A1, A2, A3, B, C, C1, D, E, E1, E2, E3)

The increment is 0.001 and the data format is E2 or A2 when the following conditions are met: Pr. 37 = "0.01 to 9998," Pr. 144 = "2 to 10," and the
instruction code HFF = "01."
REMARKS
 Set 65520 (HFFF0) as a parameter value "8888" and 65535 (HFFFF) as "9999".
 For the instruction codes HFF, HEC and HF3, their values are held once written but cleared to zero when an inverter reset or all
clear is performed.
234
Instruction
Read/
Write
Code
Write HF4 H9696: Clears the fault history as a batch
All parameters return to the initial values.
Whether to clear communication parameters or not can be selected
according to data. (: Clear, : Not clear)
Refer to page 64 for parameter clear, all clear, and communication
parameters.
All parameter clear
Write HFC
When clear is executed for H9696 or H9966, communication-related
parameter settings also return to the initial values. When resuming
operation, set the parameters again.
Executing clear will clear the instruction code HEC, HF3, and HFF
settings. Only H9966 and H55AA (all parameter clear) are valid
during the password lock.
 Turning OFF the power supply while clearing parameters with H5A5A or
H55AA also clears the communication parameter settings back to the initial
settings.
Refer to the instruction code (Refer to page 64) and write and/or read
Read H00 to H63
parameter values as required.
When setting Pr. 100 and later, link parameter extended setting must
be set.
Write H80 to HE3
Data format of Pr. 37 read and write is E2 and A2
Parameter description is changed according to the H00 to H09
Read H7F
settings.
For details of the settings, refer to the parameter instruction code
Write HFF
(Refer to page 64).
Calibration parameters are set. (Refer to the list of calibration
Read H6C
parameters on the next page.)
H00: Frequency (Writing of the gain frequency is available with Pr. 125
(instruction code H99) and Pr. 126 (instruction code H9A).)
H01: Parameter-set analog value
Write HEC
H02: Analog value input from terminal
Write/ Available for writing 2 commands, and monitoring 2 items for reading
HF0
Read data (Refer to page 237 for detail)
Reading inverter model in ASCII code.
"H20" (blank code) is set for blank area
Read H7C
Example of FR-F740PJ
H46, H52, H2D, H46, H37, H34, H30, H50, H4A, H20 ... H20
Reading inverter capacity in ASCII code.
Data is read in increments of 0.1kW, and rounds down to 0.01kW
increments
Read H7D "H20" (blank code) is set for blank area
Example
0.4K ................. "
0.75K ............... "
Data Definition
Clear Type Data
H9696
Parameter clear
H5A5A
H9966
H55AA
4" (H20, H20, H20, H20, H20, H34)
7" (H20, H20, H20, H20, H20, H37)
Communication Pr.




Number of
Data Digits
(Format)
4 digits
(A, C/D)
4 digits
(A, C/D)
4 digits
(B, E/D),
6 digits
(B, E2/D)
4 digits
(A, C/D),
6 digits
(A2, C/D)
2 digits
(B, E1/D)
2 digits
(A1, C/D)
2 digits
(B, E1/D)
2 digits
(A1, C/D)
10 digits
(A3, C1/D)
20 digits
(B, E3/D)
6 digits
(B, E2/D)