Intelliflo Vf 3050, Vs 3050 And Vsf+Svrs Pump Setup; Setting Up Intelliflo; How Many Pumps Will Intellitouch Support; Connecting Power To An Intelliflo Pump - Intellitouch User Manual

56
IntelliFlo VF 3050, VS 3050, VS+SVRS, VSF+SVRS Pump Setup

Setting up IntelliFlo

The IntelliFlo pump can be remotely controlled by an IntelliTouch system using the two-wire 50 foot RS-485
communication cable (P/N 350122). IntelliFlo operations can be adjusted from the IntelliTouch indoor control
panel or MobileTouch wireless remote. For more information refer to the following manuals: IntelliFlo VF 3050
(P/N 350075), IntelliFlo VS 3050 (P/N 357269), IntelliFlo VSF+SVRS (P/N 351420)

How many pumps will IntelliTouch support?

IntelliTouch can support up to eight IntelliFlo VF and four IntelliFlo VS pumps in any combination with up to
eight GPMs or RPMs per pump. For example pumps can be connected to IntelliTouch as follows:
•
8 IntelliFlo VF
• 7 IntelliFlo VF + 1 IntelliFlo VS (or VS+SVRS or VSF +SVRS)
• 5 IntelliFlo VF + 3 IntelliFlo VS (or VS+SVRS or VSF +SVRS
• 4 IntelliFlo VF + 4 IntelliFlo VS (or VS+SVRS or VSF +SVRS (or only 4 IntelliFlo VS pumps)

Connecting power to an IntelliFlo pump

The IntelliFlo pump is designed to be permanently connected to its power source. Typically the pump receives
power directly from the circuit breaker. No contactor or motor starter is required. The drive controls the
starting and stopping of the pump. If the IntelliFlo pump is connected to an automation system, such as the
IntelliTouch automation system, the drive must be powered up to receive and respond to the RS-485 serial
communication from the automation system. However, the pump can be operated in "stand-alone" mode,
starting and stopping when power is applied or removed. When the drive powers up it will return to the mode
and run status that it was in when power was removed. This setup maybe appropriate if you need to use existing
relays or timers.

Assigning an IntelliFlo VF 3050 pump address

Before assigning a pump address in the IntelliTouch indoor control panel, first set the address on
the pump itself. If there is only one pump, it is always seen as pump #1 by IntelliTouch. In this
case you do not need to set the pump address. When using multiple IntelliFlo pumps with
IntelliTouch you need to assign an address to each pump. The address can be set to #1, #2, #3,
#4, #5, #6, #7, or #,8. The address set at the pump must match the IntelliFlo pump number
selected in the IntelliTouch indoor control panel.
Note: IntelliFlo VF 3050 pumps cannot be connected in series with other pumps.
Check valves must be used when a pump is used in parallel with other pumps.
To assign an IntelliFlo VF 3050 pump address:
1. Press the Start/Stop button to stop the pump. Be sure that the green power LED is on and
the pump is stopped.
2. Press the Menu button.
3. Press the Up and Down arrow buttons to scroll through the menu items. Press the Select
button to access the "Pool Data" menu.
4. Press the Select button to access the "Pump Address" setting.
5. Press the Select button to change the current pump address.
6. To enter the new address number, press the Left and Right arrows to select which digit to
modify, then use the Up and Down arrows to change the selected digit.
7. When you are done assigning the pump address number, press the Enter button to save
the changes. To cancel any changes, press the Escape button to exit edit mode without saving.
IntelliTouch Pool and Spa Control System User's Guide
®
IntelliFlo
MENU 12:15
Pool Data
Back
Filter Vacuum Manual
Wash
On Enter
Warn.
Alarm
Feature Feature Start
Reset
1 2 Stop
IntelliFlo ®
Pool Data Pool Data 12:01 12:01
1
Pump Address Pump Address
Back
Filter Vacuum Manual
Wash
On Enter
Warn.
Alarm
Feature Feature Start
Reset
1 2 Stop