Setting Modifiers - Sony MLS-X1 User Manual

Frame I/O (2-channel mode) pattern numbers
2861 to 2864
No. Parameter Adjustment
1 Rot X Rotation around Y-axis (rotation in
horizontal direction)
2 Rot Y Rotation around X-axis (rotation
in vertical direction)
3 Rot Z Rotation around Z-axis
5 Delay Timing for image selected on a
utility bus to enter the frame
Brick (3-channel mode) pattern number 3601
No. Parameter Adjustment
1-1 Side V Size X Side V horizontal scaling factor
1-2 Side V Size Y Side V vertical scaling factor
1-3 Height Height of brick
1-4 Side V Center X Side V horizontal center position
b)
1-5 Side V Center Y Side V vertical center position
2-1 Side H Size X Side H horizontal scaling factor
2-2 Side H Size Y Side H vertical scaling factor
2-3 Height Height of brick
2-4 Side H Center X Side H horizontal center position
b)
2-5 Side H Center Y Side H vertical center position
a) The [Height] parameter in numbers 1-3 and 2-3 are common.
b) Side V/side H image horizontal center position. At –100.00, the center is
at the left edge of the screen. At +100.00, the center is at the right edge
of the screen.
c) Side V/side H image vertical center position. At –100.00, the center is at
the bottom edge of the screen. At +100.00, the center is at the top edge of
the screen.

Setting Modifiers

You can add modifiers to modify a DME wipe pattern.
Direction
Sets the direction of travel of the DME wipe.
Notes
• The direction cannot be set for the following patterns.
- Frame I/O pattern numbers 1201, 1202, 1203, 1205,
1206, 1208, 1209, 1225
- P in P pattern number 1251
- Mosaic pattern number 1701
- Defocus pattern number 1702
• In a key DME wipe, the direction can be set for the
following patterns.
- Frame I/O pattern numbers 1204, 1207, 1221 to 1224
- Resizer Frame I/O pattern numbers 7204, 7207, 7221
to 7224
Edge
Adds a border to a DME wipe pattern.
The edges cannot be set for the following patterns.
• Split pattern numbers 1011, 1012, 1013
• Mosaic pattern number 1701
• Defocus pattern number 1702
Position
You can move a DME wipe pattern to a desired position.
You can move to a specified position (upper left, upper
right, bottom left, bottom right) using Position Select.
The position can be set for the following patterns.
The target position and movement varies depending on
the pattern.
• Squeeze pattern number 1031
a)
c)
• Squeeze pattern numbers 1032, 1033
a)
• Frame I/O pattern numbers 1201 to 1209, 1221 to 1225
c)
• P in P pattern numbers 2651, 2652
• Brick pattern numbers 2801 to 2804, 2811 to 2814
• Frame I/O pattern numbers 2851 to 2854, 2861 to 2864
Size
Sets the size of a DME wipe pattern.
The size can be set for the following patterns.
• Frame I/O pattern numbers 1201 to 1209, 1221 to 1225,
• P in P pattern numbers 1251, 2651, 2652
• Resizer Frame I/O pattern numbers 7201 to 7208, 7221
Crop
Crops the top, bottom, left, right sides of a DME wipe
pattern.
166
Note
Resizer Squeeze pattern number 7031
As the transition progresses, the pattern center
automatically moves from the initial set position toward
the center of the screen.
You can set the pattern position at the start of the
transition. As the transition progress resumes after the
dead band, the pattern automatically moves from the
initial position toward the center of the screen.
P in P pattern number 1251
Resizer Frame I/O pattern numbers 7201 to 7208, 7221
to 7224
You can set the pattern position at the end of the first
transition.
You can configure each channel separately, or
configure two channels simultaneously, depending on
their relative positions.
You can set the vertical position where the brick slides
in.
You can set the pattern position at the end of the first
transition for each channel.
Note
2851 to 2854, 2861 to 2864
to 7224