Teledyne 100E Instruction Manual page 143

Model 100E Instruction Manual
To program the sample sequence shown above:
SAMPLE*
< TST TST > CAL CALZ CZLS
SETUP X.X
CFG DAS RNGE PASS CLK MORE EXIT
ACAL
SETUP X.X
SEQ 1) DISABLED
MODE
NEXT
SETUP X.X
SEQ 2) DISABLED
PREV NEXT
M ODE
SETUP X.X
M ODE: DISABLED
NEXT
SETUP X.X MODE: ZERO
PREV
NEXT
SETUP X.X
M ODE: ZERO–SPAN
PREV NEXT
SETUP X.X
SEQ 2) ZERO–SPAN, 1:00:00
PREV NEXT MODE
Default
SETUP X.X
TIM ER ENABLE: ON
value is
ON
EDIT
SET>
SETUP X.X
STARTING DATE: 01–JAN–02
<SET SET>
Toggle keys
to set
SETUP X.X STARTING DATE: 01–JAN–02
day, m onth &
year:
0
4 SEP
Form at :
Y
DD-MON-Y
SETUP X.X
STARTING DATE: 04–SEP–03
<SET
SET>
SETUP C.4
STARTING DATE: 04–SEP–03
<SET
SET>
SETUP C.4
STARTING TIM E:00:00
Toggle keys to
set time:
<SET SET>
Format : HH:MM
This is a 24 hr
clock .
PM hours are SETUP C.4 STARTING TIME:00:00
13 – 24.
Example 1 4 : 1
2:15 PM = 14:15
With dynamic calibration turned on, the state of the internal setup variables
DYN_SPAN and DYN_ZERO is set to ON and the instrument will reset the slope and
offset values for the SO
re-adjustment of calibration parameters can often mask subtle fault conditions in the
analyzer. It is recommended that, if dynamic calibration is enabled, the analyzer's test
045150102 Rev XB1
RANGE = 500.000 PPB SO2 =X.XXX
SETUP
PRIMARY SETUP MENU
EXIT
EXIT
ENTR EXIT
ENTR EXIT
EXIT
ENTR
EXIT
SET
EXIT
EXIT
EDIT
0 EXIT
3 ENTR
EDIT EXIT
EDIT EXIT
EXIT
EDIT
EXIT
5 ENTR
response each time the AutoCal program runs. This continuous
2
SETUP C.4
STARTING TIM E:14:15
<SET EDIT
SET>
SETUP C.4
DELTA DAYS: 1
<SET SET>
EDIT
SETUP C.4 DELTA DAYS: 1
0 0 2
SETUP C.4
DELTA DAYS:2
<SET EDIT
SET>
SETUP C.4
DELTA TIME00:00
<SET SET>
EDIT
SETUP C.4 DELTA TIME: 00:00
0 0 :3 0
SETUP C.4
DELTA TIEM:00:30
<SET EDIT
SET>
SETUP C.4
DURATION:15.0 M INUTES
<SET SET>
EDIT
SETUP C.4 DURATION 15.0MINUTES
3 0 .0
SETUP C.4
DURATION:30.0 M INUTES
<SET EDIT
SET>
SETUP C.4
CALIBRATE: OFF
<SET SET>
EDIT
SETUP C.4 CALIBRATE: OFF
ON
SETUP C.4
CALIBRATE: ON
<SET SET> EDIT
SETUP C.4
SEQ 2) ZERO–SPAN, 2:00:30
PREV NEXT MODE SET
Sequence
MODE
Calibration Procedures
EXIT
EXIT
Toggle keys
to set
number of
days
between
EXIT
ENTR
procedures
(1-367)
EXIT
EXIT
Toggle keys
to set
delay time for
each iteration
of the
EXIT
ENTR
sequence:
HH:MM
(0 – 24:00)
EXIT
Toggle keys
EXIT
to set
duration for
each
iteration of
the
sequence:
Set in
EXIT
ENTR
Decimal
minutes
from
0.1 – 60.0
EXIT
EXIT
Toggle key
between
Off and
ON
EXIT
ENTR
EXIT
EXIT returns
to the SETUP
EXIT Menu
Delta Time
Delta Days
141