Teledyne 100E Instruction Manual page 13

Model 100E Instruction Manual
LIST OF FIGURES
Figure 3-1: Location of Shipping Screws .......................................................................... 26
Figure 3-2: Rear Panel Layout ........................................................................................ 27
Figure 3-3: Analog Output Connector .............................................................................. 28
Figure 3-4: Status Output Connector............................................................................... 29
Figure 3-5: Control Input Connector ................................................................................ 30
Figure 3-6: Basic Pneumatic Connections for Units Without Valve Options ............................ 33
Figure 3-7: Basic Pneumatic Connections for Units with Valve Options ................................. 34
Figure 3-8: M100E Layout (Basic Unit - No Valve Options) ................................................. 35
Figure 3-9: Front Panel Layout ....................................................................................... 37
Figure 3-10: Pneumatic Diagram of the M100E Standard Configuration. ................................. 40
Figure 5-1: Current Loop Option Installed on the Motherboard ............................................ 47
Figure 5-2: Pneumatic Diagram of the M100E With Z/S Option Installed................................ 48
Figure 5-3: Pneumatic Diagram of the M100E with IZS Options Installed............................... 50
Figure 5-4: M100E Ethernet Card and rear panel With Ethernet Installed.............................. 53
Figure 6-1: Analog Output Connector Key ...................................................................... 63
Figure 6-2: Setup for Calibrating Analog Outputs .............................................................. 81
Figure 6-3: Setup for Calibrating Current Outputs ............................................................. 83
Figure 6-4: Status Output Connector............................................................................... 90
Figure 6-5: Control Inputs with local 5 V power supply ...................................................... 92
Figure 6-6: Control Inputs with external 5 V power supply ................................................. 92
Figure 6-7: Default iDAS Channels Setup ....................................................................... 106
Figure 6-8: APICOM user interface for configuring the iDAS. ............................................. 117
Figure 6-9: iDAS Configuration Through a Terminal Emulation Program. ............................ 118
Figure 6-10: APICOM Remote Control Program Interface ................................................... 124
Figure 7-1: Setup for Manual Calibration without Z/S valve or IZS Option .......................... 129
Figure 7-2: Setup for Manual Calibration with Z/S Valve Option Installed ........................... 133
Figure 7-3: Setup for Manual Calibration Check with Z/S Valve or IZS Option ..................... 136
Figure 9-1: Sample Particulate Filter Assembly ............................................................. 158
Figure 9-2: Zero Air Scrubber Assembly ...................................................................... 160
Figure 10-1: UV Absorption ........................................................................................... 164
Figure 10-2: UV Light Path ............................................................................................ 166
Figure 10-3: Source UV Lamp Construction ...................................................................... 167
Figure 10-4: Excitation Lamp UV Spectrum Before/After Filtration ....................................... 168
Figure 10-5: PMT Optical Filter Bandwidth........................................................................ 169
Figure 10-6: Effects of Focusing Source UV in Sample Chamber .......................................... 169
Figure 10-7: M100 Gas Flow and Location of Critical Flow Orifice......................................... 172
Figure 10-8: Flow Control Assembly & Critical Flow Orifice ................................................. 173
Figure 10-9: M100E Hydrocarbon Scrubber (Kicker) .......................................................... 174
Figure 10-10: M100E Electronic Block Diagram................................................................... 176
Figure 10-11: M100E CPU Board ...................................................................................... 178
Figure 10-12: M100E Sample Chamber ............................................................................. 179
Figure 10-13: PMT Assembly ........................................................................................... 180
Figure 10-14: Basic PMT Design ....................................................................................... 181
Figure 10-15: PMT Cooling System ................................................................................... 182
Figure 10-16: PMT Preamp Block Diagram ......................................................................... 183
Figure 10-17: Relay Board Status LED Locations................................................................. 185
Figure 10-18: Power Distribution Block Diagram ................................................................. 189
Figure 10-19: Interface Block Diagram.............................................................................. 190
Figure 10-20: M100E Front Panel Layout ........................................................................... 191
Figure 10-21: Keyboard and Display Interface Block Diagram ............................................... 192
Figure 10-22: Basic Software Operation ............................................................................ 194
Figure 11-1: Viewing and Clearing warning messages...................................................... 199
045150102 Rev XB1 xi