Teledyne 100E Instruction Manual page 15

Model 100E Instruction Manual
LIST OF TABLES
Table 2-1: Model 100E Basic Unit Specifications................................................................ 19
Table 3-1: Analog output Pin Outs.................................................................................. 28
Table 3-2: Status Output Signals....................................................................................... 29
Table 3-3: Control Input Signals..................................................................................... 30
Table 3-4: Inlet / Outlet Connector Nomenclature ............................................................. 31
Table 3-5: NIST-SRM's Available for Traceability of SO
Table 3-6: Front Panel Display During System Warm-Up .................................................... 37
Table 3-7: Possible Warning Messages at Start-Up ............................................................ 38
Table 5-1: Zero/Span Valve Operating States.................................................................. 49
Table 5-2: IZS Valve Operating States ........................................................................... 49
Table 6-1: Analyzer Operating modes ............................................................................. 55
Table 6-2: Test Functions Defined................................................................................... 57
Table 6-3: List of Warning Messages ............................................................................... 58
Table 6-4: Password Levels ........................................................................................... 60
Table 6-5: Variable Names (VARS) Revision B.3 ............................................................... 71
Table 6-6: M100E Diagnostic (DIAG) Functions................................................................. 73
Table 6-7: DIAG - Analog I/O Functions........................................................................... 76
Table 6-8: Analog Output Voltage Ranges ........................................................................ 76
Table 6-9: Analog Output Current Loop Range.................................................................. 77
Table 6-10: Analog Output Pin Assignments......................................................................... 77
Table 6-11: Voltage Tolerances for Analog Output Calibration................................................. 80
Table 6-12: Current Loop Output Calibration with Resistor ..................................................... 84
Table 6-13: Test Parameters Available for Analog Output A4 .................................................. 89
Table 6-14: Status Output Pin Assignments ......................................................................... 91
Table 6-15: Control Input Pin Assignments .......................................................................... 91
Table 6-16: COM1 and COM2 DB-9 Pin Assignments ............................................................. 95
Table 6-17: COMM Port Communication modes .................................................................... 96
Table 6-18: Ethernet Status Indicators................................................................................ 99
Table 6-19: Front Panel LED Status Indicators for iDAS ....................................................... 103
Table 6-20: iDAS Data Channel Properties ......................................................................... 104
Table 6-21: iDAS Data Parameter Functions....................................................................... 105
Table 6-22: Terminal Mode Software Commands ................................................................ 119
Table 6-23: Command Types ........................................................................................... 120
Table 6-24: Serial Interface Documents ............................................................................ 125
Table 7-1: NIST-SRM's Available for Traceability of SO
Table 7-2: AutoCal Modes............................................................................................ 139
Table 7-3: AutoCal Attribute Setup Parameters............................................................... 139
Table 7-4: Example Auto-Cal Sequence ......................................................................... 140
Table 7-5: Calibration Data Quality Evaluation................................................................ 142
Table 8-1: Activity Matrix for Calibration Equipment & Supplies ........................................... 144
Table 8-2: Activity Matrix for Calibration Procedure ............................................................ 145
Table 8-3: Activity Matrix ............................................................................................... 147
Table 8-4: Definition of Level 1 and Level 2 Zero and Span Checks ....................................... 148
Table 9-1: M100E Preventive Maintenance Schedule ......................................................... 156
Table 9-2: Predictive Uses for Test Functions ............................................................... 157
Table 10-1: Relay Board Status LED's ............................................................................... 185
Table 10-2: Front Panel Status LED's .............................................................................. 191
Table 11-1: Test Functions - Possible Causes for Out-Of-Range Values.............................. 199
Table 11-2: Relay Board Status LEDs ........................................................................... 203
Table 11-3: DC Power Test Point and Wiring Color Code.................................................. 211
Table 11-4: DC Power Supply Acceptable Levels ............................................................ 211
Table 11-5: Relay Board Control Devices ...................................................................... 212
045150102 Rev XB1
Calibration Gases ............................. 33
2
Calibration Gases ........................... 128
2
xiii