ProMinent DULCOMETER PH-501 Assembly And Operating Instructions Manual page 840

Aeon PD Extreme Duty Lubricant .................................. 20
Aeon PD Food Grade Lubricant .................................... 20
Aeon PD Synthetic Lubricant......................................... 20
Air Filters And Filter Silencers ....................................... 16
Assembly Instructions, Section 7 ................................... 31
Blower Startup Checklist ............................................... 23
Disassembly Instructions, Section 6 .............................. 27
Drive End Lubrication.............................................. 17, 18
Drive Installation ........................................................... 13
Equipment Check, Section 1 ......................................... 10
Foundations ................................................................. 12
Gear End Lubrication .................................................... 18
Installation, Section 2 .................................................... 12
Installing The Timing Gears .......................................... 36
Introduction ....................................................................9
Limitations .................................................................... 22
Location ....................................................................... 12
Lubrication, Section 3 ................................................... 17
FIGURE 2-1 – BLOWER MOUNTING CONFIGURATION ......................................................................... 13
FIGURE 2-2 – BELT DRIVE OVERHUNG LOAD CALCULATIONS ........................................................... 15
FIGURE 3-1 - LUBRICATION ................................................................................................................... 17
FIGURE 3-2 – APPROXIMATE OIL CAPACITIES ..................................................................................... 18
FIGURE 3-3 – AEON PD SYNTHETIC LUBRICANT ................................................................................. 20
FIGURE 3-4 – SYNTHETIC LUBRICANT CHART ..................................................................................... 20
FIGURE 3-5 – LUBRICATION RECOMMENDATION ................................................................................ 21
FIGURE 4-1 – MAXIMUM / MINIMUM OPERATING LIMITATIONS ........................................................... 22
FIGURE 5-1 – PULLER PLATE ................................................................................................................ 25
FIGURE 5-2 – SEAL DRIVE .................................................................................................................... 25
FIGURE 5-3 – MECHANICAL SEAL INSTALLATION TOOL ...................................................................... 26
FIGURE 5-4 – BEARING PRESS TOOL – MECHANICAL SEAL UNITS .................................................... 26
FIGURE 6-1 – DISASSEMBLY ILLUSTRATIONS ..................................................................................... 27
FIGURE 6-2 – DISASSEMBLY ILLUSTRATIONS ..................................................................................... 27
FIGURE 6-3 – DISASSEMBLY ILLUSTRATIONS ..................................................................................... 28
FIGURE 6-4 – DISASSEMBLY ILLUSTRATIONS ..................................................................................... 28
FIGURE 6-5 – DISASSEMBLY ILLUSTRATIONS ..................................................................................... 28
FIGURE 6-6 – DISASSEMBLY ILLUSTRATIONS ..................................................................................... 29
FIGURE 7-1 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 31
FIGURE 7-2 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 32
FIGURE 7-3 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 32
FIGURE 7-4 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 33
FIGURE 7-5 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 34
FIGURE 7-6 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 34
FIGURE 7-7 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 34
FIGURE 7-8 – ASSEMBLY ILLUSTRATIONS ........................................................................................... 37
FIGURE 7-9 – TORQUE FT LBS .............................................................................................................. 38
Mechanical Seals Only ........................................... 31, 32
Mounting Configurations ............................................... 12
Operation, Section 4 ..................................................... 22
Parts List, Section 8...................................................... 39
Piping .......................................................................... 14
Recommended Lubricant .............................................. 20
Removing Protective Materials ...................................... 10
Repositioning The Mounting Feet .................................. 12
Safety Precautions ......................................................... 5
Safety Precautions ....................................................... 24
Section 7
Assembly Instructions ................................................... 31
Setting Impeller End Clearance With Mechanical Seals . 35
Setting Impeller End Clearances ................................... 34
Special Tools Required Section 5 ................................. 25
Storage ........................................................................ 10
Trouble Shooting .......................................................... 24
Warranty ...................................................................... 63
E-97