WAGO -I/O-SYSTEM 750 Manual page 221

WAGO-I/O-SYSTEM 750
750-375 PROFINET IO advanced Fieldbus Coupler
Table 165: Parameterization AI, 3 PM - Attribute "Peak value phase" ............. 185
Table 166: Parameterization AI, 3 PM - Attribute "Autoreset min./max. value"
.................................................................................................................... 185
Table 167: Parameterization AI, 3 PM - Attribute "User scaling" ..................... 186
Table 168: Parameterization AI, 3 PM - Attribute "Scaling energy consumption"
.................................................................................................................... 186
Table 169: Parameterization AI, 3 PM - Attribute "Scaling energy consumption"
.................................................................................................................... 186
Table 170: Parameterization AI, 3 PM - Attribute "Storage interval energy [s]"
.................................................................................................................... 186
Table 171: Parameterization AI, 3 PM - Attribute "Current transformer ratio" . 186
Table 172: Parameterization AI, 3 PM - Attribute "Peak value meas. interval
[HW]" ......................................................................................................... 186
Table 173: Parameterization AI, 3 PM - Attribute "Min./Max. reset interval
[200ms]" ..................................................................................................... 187
Table 174: Parameterization - Overview of Attributes for Analog Output Modules
(AO) ........................................................................................................... 187
Table 175: Parameterization AO - Attribute "Substitute value behavior".......... 187
Table 176: Parameterization AO - Attribute "Substitute value (2 Byte)" .......... 188
Table 177: Parameterization - Overview of additional Attributes for Analog
Output Modules with Diagnostics (AO, DIA) ........................................... 188
Table 178: Parameterization AO, DIA - Attribute "Channel diagnosis" ............ 188
Table 179: Parameterization AO, DIA - Attribute "Diagnosis: Short circuit" ... 188
Table 180: Parameterization AO, DIA - Attribute "Diagnosis: Undervoltage" . 188
Table 181: Parameterization AO, DIA - Attribute "Diagnosis: Overtemperature"
.................................................................................................................... 189
Table 182: Parameterization AO, DIA - Attribute "Diagnosis: Error" ............... 189
Table 183: Parameterization AO, DIA - Attribute "Diagnosis: External fault" . 189
Table 184: Parameterization - Overview of Additional Attributes for Special AO
Module Types with Parameter Channel(AO, 562, 563) ............................ 190
Table 185: Parameterization AO, 562, 563 - Attribute "User scaling" .............. 190
Table 186: Parameterization AO, 562, 563 - Attribute "Calibration" ................ 190
Table 187: Parameterization AO, 562, 563 - Attribute "Number representation"
.................................................................................................................... 190
Table 188: Parameterization AO, 562, 563 - Attribute "Operating mode" ........ 190
Table 189: Parameterization AO, 562, 563 - Attribute "On exceeding user limits"
.................................................................................................................... 190
Table 190: Parameterization AO, 562, 563 - Attribute "Output" ....................... 191
Table 191: Parameterization AO, 562, 563 - Attribute "Behavior on K-Bus
timeout" ...................................................................................................... 191
Table 192: Parameterization AO, 562, 563 - Attribute "Switch-on delay [s]" ... 191
Table 193: Parameterization - Overview of Additional Attributes for
PROFIenergy Submodules (AO, PE) ........................................................ 191
Table 194: Parameterization AO, PE - Attribute "Minimal pause time"............ 192
Table 195: Parameterization DO, PE - Attribute "Pause output value" ............. 192
Table 196: Parameterization SF, DIA - Attribute "Channel diagnosis" ............. 192
Table 197: Parameterization SF, DIA - Attribute "Diagnosis: External fault" .. 192
Table 198: Parameterization SF, DIA - Attribute "Diagnosis: Error" ................ 193
Table 199: Parameterization SF, DIA - Attribute "Diagnosis: Undervoltage"... 193
Manual
Version 1.1.0
List of Tables 221