Omron Q2V Series Technical Manual page 359

No.
Name
(Hex.)
H3-11 AI2 Gain Setting
(0419)
RUN
H3-12 AI2 Bias Setting
(041A)
RUN
H3-13 An.In FilterTime
Constant
(041B)
H3-14 An.In Term.Enable Sel
(041C)
H3-16 AI1 Offset
(02F0)
H3-17 AI2 Offset
(02F1)
H3-40 15C1h Input Function
(0B5C)
H3-41 15C2h Input Function
(0B5F)
H3-42 15C3h Input Function
(0B62)
H3-43 Mbus In FilterTime
Const
(117F)
■
H3-xx: MFAI Function Select
Setting Value Function
0 Through Mode
1 AuxFreqRef1
2 AuxFreqRef2
3 FrqBIAS Frq
4 Freq Ref/BIAS
5 Freq Gain
6 Output Voltage Bias
7 TorqCompensation
SIEPCYEUOQ2V01A Q2V Technical Manual
Description
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the gain of the analog signal input to MFAI terminal AI2.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the bias of the analog signal input to MFAI terminal AI2.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the time constant for primary delay filters on MFAI terminals.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the enabled terminal or terminals when H1-xx = 12 [MFDI Function Select = AI
Input Sel] is ON.
1 : AI1 only
2 : AI2 only
3 : AI1 and AI2
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the offset level for analog signals input to terminal AI1. Usually it is not necessary
to change this setting.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the offset level for analog signals input to terminal AI2. Usually it is not necessary
to change this setting.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the Modbus AI1 function.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the Modbus AI2 function.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the Modbus AI3 function.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the time constant to apply a primary delay filter to the Modbus analog input
terminal.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Use this setting for unused terminals or to use terminals in through mode.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets Reference 2 through multi-step speed reference to enable the command reference (Auxiliary Frequency
Reference 1) from the analog input terminal set here. This value is a percentage where the Maximum Output
Frequency setting is a setting value of 100%.
Note:
Parameter A1-02 [Control Method] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZ Vector]: E1-04 [Max Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets Reference 3 through multi-step speed reference to enable the command reference (Auxiliary Frequency
Reference 2) from the analog input terminal set here. This value is a percentage where the Maximum Output
Frequency setting is a setting value of 100%.
Note:
Parameter A1-02 [Control Method] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZ Vector]: E1-04 [Max Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Enters the bias value added to the frequency reference as a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZ Vector]: E1-04 [Max Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
The input value from the MFAI terminal set with this function becomes the master frequency reference.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
The drive multiplies the analog frequency reference with the input value from the MFAI set with this function.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Set this parameter to input a bias signal to amplify the output voltage.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Enters the torque compensation value if the motor rated torque is 100%.
Description
11.9 H: TERMINALS
Default
Ref.
(Range)
100.0% 611
(-999.9 - +999.9%)
0.0% 611
(-999.9 - +999.9%)
0.03 s 611
(0.00 - 2.00 s)
3 612
(1, 2, 3)
0 612
(-500 - +500)
0 612
(-500 - +500)
0 612
(0, 3, 6 - 2F)
0 612
(0, 3, 6 - 2F)
0 613
(0, 3, 6 - 2F)
0.00 s 613
(0.00 - 2.00 s)
Ref.
613
613
613
613
613
614
614
614
359
11