Omron Q2V Series Technical Manual page 350

11.9 H: TERMINALS
Setting Value Function
11 LOC/REM Sel.
12 AI Input Sel
15 FWD/REV Det
16 Ref Sample
17 Ac/Dec Hold
18 Ac/Dec Time1
19 Ac/Dec Time2
1A Drive Enable
1B Baseblock NO
1E Baseblock NC
20 to 2F External Fault
30 DCInj Cmd
32 HiSlipBraking
34 Fast Stop NO
35 Fast Stop NC
350
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets drive control for the keypad (LOCAL) or an external source (REMOTE).
ON : LOCAL
OFF : REMOTE
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the command that enables or disables the terminals selected in H3-14 [An.In Term.Enable Sel].
ON : Input to the terminal selected with H3-14 is enabled
OFF : Input to the terminal selected with H3-14 is disabled
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Set the motor rotation direction when you use Simple Closed Loop V/f Control method.
ON : Reverse run
OFF : Forward run
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the command to sample the frequency reference at terminal AI1 or AI2, and hold the frequency reference at
that frequency.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Momentarily pauses motor acceleration and deceleration when the terminal is turned ON, retains the output
frequency that was stored in the drive at the time of the pause, and restarts motor operation.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the drive to use Acceleration/Deceleration Time 1 [C1-01, C1-02] or Acceleration/Deceleration Time 2 [C1-
03, C1-04].
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Set this function and H1-xx = 18 [Ac/Dec Time1] together. Sets the drive to use Acceleration/Deceleration Time 3
[C1-05, C1-06] or Acceleration/Deceleration Time 4 [C1-07, C1-08].
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function to show dnE [Drive Enabled] on the keypad and ignore Run commands when the terminal is
OFF.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the command that stops drive output and coasts the motor to stop when the input is ON.
ON : Baseblock (drive output stop)
OFF : Normal operation
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the command that stops drive output and coasts the motor to stop when the input terminal is OFF.
ON : Normal operation
OFF : Baseblock (drive output stop)
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets a command to stop the drive when a failure or fault occurs on an external device.
20 : External Fault (ExF NO-AlRmp)
21 : External Fault (ExF NC-AlRmp)
22 : External Fault (ExF NO-RnRmp)
23 : External Fault (ExF NC-RnRmp)
24 : External Fault (ExF NO-AlCoast)
25 : External Fault ExF NC-AlCoast)
26 : External Fault (ExF NO-RnCoast)
27 : External Fault (ExF NC-RnCoast)
28 : External Fault (ExF NO-AlFStop)
29 : External Fault (ExF NC-AlFStop)
2A : External Fault (ExF NO-RnFStop)
2B : External Fault (ExF NC-RnFStop)
2C : External Fault (ExF NO-AlAlarm)
2D : External Fault (ExF NC-AlAlarm)
2E : External Fault (ExF NO-RnAlarm)
2F : External Fault (ExF NC-RnAlarm)
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the command to use DC Injection Braking to stop the motor.
Note:
When A1-02 = 8 [Control Method = EZ Vector], this function is available only when you use a PM motor.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the command to use high-slip braking to stop the motor.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the command to ramp to stop in the deceleration time set in C1-09 [Fast Stop Time] when the input terminal is
activated while the drive is operating.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the command to ramp to stop in the deceleration time set in C1-09 [Fast Stop Time] when the input terminal is
activated while the drive is operating.
Description
SIEPCYEUOQ2V01A Q2V Technical Manual
Ref.
573
574
574
574
574
575
575
575
575
576
576
577
577
577
577