Input Specifications - Mitsubishi Electric MELSEC iQ-F FX5 User Manual

*1 The number of control axes is two when the pulse output mode is CW/CCW mode.
*2 High-speed pulse input/output module is not supported.
*3 Set the number of output pulses per operation to 2147483647 or lower.
*4 For the start speed, refer to Page 79 Start speed.
2.2

Input Specifications

The input specifications of the CPU module and high-speed pulse input/output module are explained below.
Note that the simultaneous turning-on rate of CPU module is restricted. For details on this restriction, refer to the following
manual.
MELSEC iQ-F FX5U User's Manual (Hardware)
MELSEC iQ-F FX5UC User's Manual (Hardware)
FX5U CPU module
Item
Input signal voltage
Input impedance
Input signal current
ON input sensitivity current
OFF input sensitivity current
Input response time FX5U-32MT/
(H/W filter delay)
FX5U-64MT/, FX5U-80MT/
FX5U-32TM/
FX5U-64MT/, FX5U-80MT/
Input response time (Digital filter setting value)
Input signal type
Input circuit insulation
Indication of input motion
FX5UC CPU module
Item
Input signal voltage
Input impedance
Input signal current
ON input sensitivity current
OFF input sensitivity current
Input response time FX5UC-32MT/
(H/W filter delay)
FX5UC-64MT/, FX5UC-96MT/
FX5UC-32MT/
FX5UC-64MT/, FX5UC-96MT/
FX5UC-64MT/, FX5UC-96MT/
Input response time (Digital filter setting value)
Specifications
24 V DC +20%, -15%
X0 to X17 4.3 kΩ
X20 and subsequent 5.6 kΩ
X0 to X17 5.3 mA/24 V DC
X20 or subsequent 4 mA/24 V DC
X0 to X17 3.5 mA or more
X20 or subsequent 3.0 mA or more
1.5 mA or less
ON: 2.5 μs or less
X0 to X5
OFF: 2.5 μs or less
X0 to X7
X6 to X17 ON: 30 μs or less
OFF: 50 μs or less
X10 to X17
X20 or subsequent ON: 50 μs or less
OFF: 150μs or less
None, 10 μs, 50 μs, 0.1 ms, 0.2 ms, 0.4 ms, 0.6 ms, 1 ms, 5 ms, 10 ms
(initial values), 20 ms, 70 ms
No-voltage contact input
Sink input: NPN open collector transistor
Source input: PNP open collector transistor
Photocoupler insulation
Turning on the input will light the LED indicator lamp
Specifications
24 V DC +20%, -15%
X0 to X17 4.3 kΩ
X20 or subsequent 5.6 kΩ
X0 to X17 5.3 mA/24 V DC
X20 or subsequent 4.0 mA/24 V DC
X0 to X17 3.5 mA or more
X20 or subsequent 3.0 mA or more
1.5 mA or less
X0 to X5 ON: 2.5 μs or less
OFF: 2.5 μs or less
X0 to X7
X6 to X17 ON: 30 μs or less
OFF: 50 μs or less
X10 to X17
ON: 50 μs or less
X20 or subsequent
OFF: 150 μs or less
None, 10 μs, 50 μs, 0.1 ms, 0.2 ms, 0.4 ms, 0.6 ms, 1 ms, 5 ms, 10 ms
(initial values), 20 ms, 70 ms
2 SPECIFICATIONS
17
2.2 Input Specifications
2