Danfoss VLT AutomationDrive FC 300 Design Manual page 272

FC 300 Design Guide
Q
.......................................
Quick Menu
.......................................
Quick Menu mode
........................................
Quick Menu Password
.......................................
Quick Stop Ramp Time
.............................................
Quick Stop Select
Quick Transfer of Parameter Settings
R
Ramp 1 Ramp Down Time
.......................................
Ramp 1 Ramp up Time
...................................................
Ramp 1 Type
Ramp 2 Ramp down Time
Ramp 3 Ramp down Time
.......................................
Ramp 3 Ramp up Time
Ramp 4 Ramp Down Time
....................................................
Ramp Delay
.....................................................
Ramp Time
..............................................
Rated motor speed
..........................................................
RCD
Read Parameter Description Elements
............................................
Reference Handling
........................................
Reference Resource 1
.............................................
Regional Settings
Relative Scaling Reference Resource
.............................................
Relay Connection
.............................................
Relay outputs
............................................................
Reset
Reset Control Word Timeout
...........................................
Reset kWh Counter
....................................................
Reset Mode
Residual Current Device
........................................................
Rise time
Rotor Leakage Reactance (X2)
........................................
Rotor Resistance (Rr)
S
...........................................
screened/armoured
..................................................
Step-by-Step
....................................................
Safe Stop
.........................................
Safe Stop Installation
................................................
Safety Earthing
Scaling of References and Feedback
........................
Serial communication
Side-by-side installation
.....................................
Smart Logic Control
..............................................
Software versions
............................................
Speed closed loop
..............................................
Speed open loop
...................................................
Speed PID
............................................
Speed PID Control
272
120, 120, 125
120, 125
.....................
...................................
...................................
...................................
...................................
....................
......................
59, 168
................................
......................................
.............................
........................
10, 60, 108, 253
......................................
49, 194
MG.33.B4.02 - VLT is a registered Danfoss trademark
Index
Speed PID Lowpass Filter Time
...............................................
Start Delay
...........................................
Start Function
Start Speed [Hz]
140
Start Speed [RPM]
160
......................................................
Start/Stop
182
Stator leakage reactance
122
Stator Leakage Reactance (X1)
Stator Resistance (Rs)
...........................................................
Status
Status messages
157
.............................................
Status Word
157
.......................................................
Step Size
157
...................................................
Surroundings
158
Switches S201, S202, and S801
158
Switching Frequency
158
159
161
T
161
Telegram Structure
9
Telegram Traffic
12, 45
Temperature-Dependent Switch Frequency
255
Term 32/33 Encoder Direction
26
Term 32/33 Gear Denominator
155
Term 32/33 Gear Numerator
134
Term. 29 Low Frequency
156
.....................................................
Terminal 37
101
Terminal 53 High Current
Terminal 53 Low Current
122
Terminal 54 High Current
181
Terminal 54 Low Current
208
............................................
Thermal load
205
Thermal motor protection
45
................................................
Thermistor
62
This Set-Up Linked to
143
Tightening Torques
143
Torque characteristics
..................................................
Torque control
.......................................
Torque limit
Torque Limit Generator Mode
95
Trip Delay at Torque Limit
129
18, 51
98
U
105
.....................................................
Upper limit
27
USB Connection
Use of EMC-Correct Cables
83
75
V
141
141
Variable torque
20, 21
Vibration and Shock
32
.............................
..............................................
............................................
....................................
............................
.......................................
..............................................
............................
.........................................
...........................................
...............................................
..............................
.............................
................................
....................................
....................................
....................................
....................................
....................................
....................................
........................................
............................................
.........................................
...............................
...................................
............................................
..................................
................................................
...........................................
177
147, 147
147, 147
148
148
111
142
143
143
120
119
246, 251
160
60
95
204
236
236
...............
64
173
173
173
171
50
174
174
175
175
145, 214
88
12, 149
135
95
56
20
158, 159, 160
162
206
259
93, 93
107
141
19