Table of Contents
Advertisement
8T - 2
POWER MIRRORS
•
MIRROR SWITCH TEST PROCEDURE
(1) Remove power m i r r o r s w i t c h from m o u n t i n g po-
s i t i o n (refer t o Service Procedures).
(2) Disconnect w i r i n g harness a t s w i t c h connector.
(3) U s i n g a c o n t i n u i t y tester or ohmmeter, test for
c o n t i n u i t y (no resistance) between t h e t e r m i n a l s o f
t h e s w i t c h as shown i n the M I R R O R S W I T C H C O N -
T I N U I T Y
C H A R T .
(4) I f results shown i n the ch art are not obtained,
replace t h e switch.
MIRROR SWITCH CONTINUITY CHART
Mirror Selector Knob In "I" Position
MOVE LEVER
CONTINUITY BETWEEN
WT and BK
YL and PK and YL/BK and PK
WT and PK,
DB/WT and BK and DB & BK
YL/BK and BK, YL and BK
DB and PK
WT and BK, DB/WT and PK
DB and PK
Mirror Selector Knob in "R" Position
MOVE LEVER
CONTINUITY BETWEEN
WT/BK and BK, YL and PK
YL/BK and PK
i
WT/BK and PK, DB and BK
DB/WT and BK
WT/BK and PK, YL and BK
YL/BK and BK
«
WT/BK and BK, DB and PK
DB/WT and PK
J908T-9
S E R V I C E P R O C E D U R E S
MIRROR SWITCH REPLACEMENT
REMOVAL
(1) Remove 2 screws holding map l a m p and remove
map l a m p .
(2) Remove 6 screws w h i c h attach i n s t r u m e n t clus-
ter bezel t o i n s t r u m e n t panel (Fig. 2). M a k e sure the
screw below the H e a t e r \ A / C control is removed.
Fig. 2 Instrument Cluster Bezel
(3) Place column shift lever i n Position 1.
(4) Remove bezel by p u l l i n g top edge r e a r w a r d t o
clear brow. Disengage a t t a c h i n g clips a r o u n d bottom
of bezel and complete removal of bezel.
(5) I f the bezel has a four wheel d r i v e indicator, re-
move bulb socket as bezel is removed.
(6) Disconnect message center wires.
(7) Remove i n s t r u m e n t cluster bezel assembly.
(8) Remove headlamp s w i t c h knob a n d stem b y
reaching under i n s t r u m e n t panel a n d depressing but-
t o n on side of switch w h i l e p u l l i n g stem out.
(9) Remove switch bezel r e t a i n i n g screws a n d p u l l
bezel out o f i n s t r u m e n t panel (Fig. 1).
(10) P u l l harness o u t t h r o u g h opening i n i n s t r u -
m e n t panel and disconnect m i r r o r s w i t c h connector.
(11) Remove 2 switch mounting-plate-to-bezel re-
t a i n i n g screws.
(12) Remove switch-to-mounting-plate n u t .
For I n s t a l l a t i o n , reverse removal procedures.
MIRROR ASSEMBLY REPLACEMENT
REMOVAL
(1) Remove remote control handle (Fig. 3).
(2) Remove power window/lock s w i t c h b y i n s e r t i n g
a standard blade screwdriver i n t o notch o n f o r w a r d
Advertisement
Table of Contents
