Speed Control Servo; Servo Throttle Cable Assembly; Steering Column Cover - Dodge D150 1990 Service Manual

•
SPEED CONTROL SYSTEM 8H - 9
S E R V I C E P R O C E D U R E S
INDEX
Paga
Servo Throttle Cabel Assembly . . . . . . . . . . . . . . . . 9
Speed Control Servo
9
SPEED CONTROL SERVO
REMOVAL
(1) Remove t w o nuts a t t a c h i n g t h r o t t l e cable a n d
m o u n t i n g bracket t o servo.
(2) Remove t w o screws a t t a c h i n g servo m o u n t i n g
bracket to U - N u t s o n battery t r a y .
(3) Remove servo m o u n t i n g bracket.
(4) Disconnect electrical connector a n d v a c u u m
hose.
(5) P u l l cable away from servo t o expose r e t a i n i n g
clip and remove clip attaching cable to servo.
INSTALLATION
(1) W i t h t h r o t t l e i n f u l l open position a l i g n hole i n
t h r o t t l e cable sleeve w i t h hole i n servo p i n a n d i n -
s t a l l r e t a i n i n g clip.
(2) Connect v a c u u m hose t o servo.
(3) Connect electrical connector.
(4) Position m o u n t i n g bracket a n d i n s t a l l t w o
screws a t t a c h i n g bracket to battery t r a y , t i g h t e n t o
12 N*m (105 i n . lbs.).
(5) Insert servo studs t h r o u g h holes i n t h r o t t l e ca-
ble and m o u n t i n g bracket.
(6) I n s t a l l n u t s , t i g h t e n to 9 N * m (80 i n . lbs.).
SERVO THROTTLE CABLE ASSEMBLY
REMOVAL
(1) Remove a i r cleaner.
(2) Disconnect cable a t r e t a i n i n g clamp a n d a t car-
buretor ( t h r o t t l e body), removing snap r i n g (retain-
i n g clip).
(3) Disconnect cable a t servo a n d remove cable as-
sembly.
INSTALLATION
(1) Locate cable t h r o u g h servo m o u n t i n g bracket.
(2) Connect cable sleeve to servo stud, a l i g n holes,
and i n s t a l l h a i r p i n clip.
(3) Insert servo studs t h r o u g h holes i n cable a n d
holes i n bracket, i n s t a l l nut-washers, a n d t i g h t e n t o
9 N i n (80 i n . lbs.).
Page
Speed Control Switch
9
Speed Control Vacuum Reservoir Replacement
. . 1 0
(4) Route cable from servo, t h r o u g h cable support
bracket a n d clip, and i n s t a l l cable end o n stud of
t h r o t t l e body.
(5) Adjust cable as described under speed control
cable adjustment.
(6) Replace a i r cleaner.
SPEED CONTROL SWITCH (Turn Signal Lever)
REMOVAL
(1) Disconnect battery negative cable.
(2) Remove four screws a t t a c h i n g lower steering
column cover a n d remove cover ( F i g . 1). T h e fuse
block is attached to this cover a n d should be sup-
ported w h e n cover is removed.
Fig. 1 Steering Column Cover
(3) Remove w i r i n g t r o u g h after unsnapping four
plastic r e t a i n i n g clips (Fig. 2).
(4) Disconnect speed control switch electrical con-
nector from i n s t r u m e n t panel harness connector.
(5) P u l l wiper control knob from end of t u r n signal
lever.
(6) Remove silencer from lever.
(7) Remove t w o screws attaching speed control
switch to column.