Table of Contents
Advertisement
8E - 16
INSTRUMENT PANEL AND GAUGES
(3) Remove one toe plate screw.
(4) Remove four screws attaching lower steering
column cover and remove cover. The fuse block is at-
tached to t h i s cover a n d should be supported when
cover is removed.
(5) Spread upper steering column cover o u t o f lock-
ing tangs and slide
downward.
(6) Disconnect cable f r o m shift indicator bracket.
(7) Remove t w o nuts and washers a t t a c h i n g steer-
i n g column bracket t o i n s t r u m e n t panel steering col-
u m n support bracket.
(8) A l l o w column to lower and rest on seat.
RAISING STEERING
COLUMN
(1) Raise steering column assembly against the i n -
strument panel support b r a c k e t
(2) I n s t a l l t w o steering column bracket
washers
and nuts (Finger T i g h t e n Only).
CAUTION: Check that all wiring is clear and not
pinched.
(3) T i g h t e n the two bracket nuts to 12 N*m (110 i n .
lbs.) torque.
(4) Slide toe plate i n t o position, i n s t a l l a t t a c h i n g
screw, t i g h t e n t o 4 N»m (35 i n . lbs.).
(5) I n s t a l l toe plate nuts and washers a n d t i g h t e n
to 23 N«m (200 i n . lbs.).
(6) Connect cable to shift indicator bracket.
(7) Position upper steering column cover and slide
upward u n t i l tangs snap i n t o place.
(8) I n s t a l l fuse block t o cover.
(9) Position lower steering column cover a n d i n s t a l l
four a t t a c h i n g screws.
HEATER CONTROL
REMOVAL
(1) Remove map lamp.
(2) Remove cluster bezel (refer to Cluster Bezel Re-
moval).
(3) Remove two control attaching screws.
(4) P u l l control rearward.
(5) Disconnect i l l u m i n a t i o n lamp, and w i r e connec-
tions.
(6) Disconnect control cables.
(7) Remove control.
INSTALLATION
(1) Position control near panel.
(2) Connect control cables t o control (see Heater A/
C Section).
(3) Connect i l l u m i n a t i o n l a m p , a n d w i r e connec-
tors.
(4) Push control i n t o panel.
(5) I n s t a l l t w o control m o u n t i n g screws.
(6) I n s t a l l bezel.
(7) I n s t a l l m a p lamp.
HEATER A/C CONTROL
REMOVAL
(1) Remove map lamp.
(2) Remove cluster bezel (refer t o Cluster Bezel Re-
moval).
(3) Remove t w o control a t t a c h i n g screws.
(4) P u l l control rearward.
(5) Disconnect blower s w i t c h w i r i n g .
(6) Disconnect wires t o p u s h b u t t o n switch (three
connectors).
(7) Disconnect i l l u m i n a t i o n l a m p .
(8) Disconnect vacuum harness.
(9) Disconnect temperature cable.
(10) Remove control.
INSTALLATION
(1) Position control near panel.
(2) Connect temperature cable (see Group 24 -
H e a t i n g a n d A i r Conditioning).
(3) Connect v a c u u m harness.
(4) Connect i l l u m i n a t i o n l a m p .
(5) A t t a c h three w i r e connectors to pushbutton
switch.
(6) Connect wires to blower motor switch.
(7) Push control i n t o panel.
(8) I n s t a l l t w o control m o u n t i n g screws.
(9) I n s t a l l cluster bezel.
(10) I n s t a l l map lamp.
SWITCHES
HEADLAMP
SWITCH (FIG. 2)
Removal
(1) Remove cluster bezel (refer t o Cluster Bezel Re-
moval).
(2) Reaching under i n s t r u m e n t panel, depress knob
and stem release b u t t o n located on bottom of switch
housing and a t same t i m e p u l l knob and stem assem-
bly out of s w i t c h housing located on front of panel.
(3) Remove power m i r r o r s w i t c h knob by p u l l i n g
straight off.
(4) Remove bezel.
Advertisement
Table of Contents
