Exterior Lamps Service Procedures; Sealed Beam Replacement; Side Marker Lamp And Bulb; Tail, Stop, Turn Signal, Rear Side Marker And Back-Up Lamps - Dodge D150 1990 Service Manual

•
LAMPS 8L - 3
E X T E R I O R LAMPS S E R V I C E P R O C E D U R E S
INDEX
Page
Cargo Lamp Bulb 5
Daytime Running Lights (Canada Only)
9
Front Park And Turn Signal Lamp Bulb . . . . . . . . . 3
Headlamp Aiming Procedures
7
Headlamp Dimmer Switch 7
Headlamp Switch
6
I.D. And Clearance Lamps For Dual Wheel Model . 4
SEALED BEAM REPLACEMENT
(1) Remove screws f r o m headlamp bezel (Fig. 1).
HEADLAMP
BEZEL &
PARKING LAMP
ASSEMBLY
SEALED
BEAM
J908L-72
Fig. 1 Sealed Beam Replacement
(2) Twist o u t p a r k a n d t u r n signal l a m p socket
f r o m back of l a m p housing. Set Headlamp bezel
aside.
(3) Remove screws f r o m r e t a i n i n g r i n g , and remove
r i n g (Fig. 2). D o n o t d i s t u r b h e a d l a m p a i m i n g
s c r e w s .
(4) P u l l out sealed beam u n i t and u n p l u g connec-
tor, by p u l l i n g i t s t r a i g h t off.
(5) Position new sealed beam u n i t and i n s t a l l con-
nector.
(6) I n s t a l l r e t a i n i n g r i n g .
(7) Install headlamp bezel.
(8) A i m Headlamp as described i n Headlamp A i m -
i n g Procedures.
FRONT PARK AND TURN SIGNAL LAMP BULB
(1) Remove screws f r o m headlamp bezel (Fig. 1).
(2) Twist o u t p a r k a n d t u r n signal l a m p socket
f r o m back of l a m p housing.
(3) Replace bulb.
To install, reverse r e m o v a l procedures.
Page
License Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Sealed Beam Replacememt 3
Side Marker Lamp And Bulb 3
Tail, Stop, Turn Signal, Rear Side Marker And
Back-Up Lamps . 3
Underhood Retractable Lamp 10
SIDE MARKER LAMP AND BULB
(1) T w i s t out socket f r o m back of housing.
(2) Remove n u t s a t t a c h i n g l a m p assembly t o
fender.
(3) L i f t l a m p assembly away from outside of fender.
To i n s t a l l , reverse t h e removal procedures.
TAIL, STOP. TURN SIGNAL, REAR SIDE MARKER
AND BACK-UP LAMPS
SWEPTLINE MODELS (FIG. 2)
To replace bulbs, remove lamp.
REMOVAL
(1) Remove assembly attachment screws and re-
move lamp assembly.
(2) T w i s t out socket.
CONNECTOR
BLACK MOLD
r
J " NUT
*LAMP ASSEMBLY
-SCREW
RN991
Fig. 2 Tail, Stop, Turn Signal, Rear Side Marker and
Back-Up Lamp
INSTALLATION
(1) T w i s t i n socket.
(2) Position t h e l a m p and i n s t a l l assembly mount-
i n g screws.