Dodge RAM 1500 2020 Owner's Manual

Table of Contents

Quick Links

RAM 1500

20 2 0 OWNER' S M ANUAL

Table of Contents

Need help?

Do you have a question about the RAM 1500 2020 and is the answer not in the manual?

Questions and answers

Summary of Contents for Dodge RAM 1500 2020

Page 1 RAM 1500 20 2 0 OWNER’ S M ANUAL...
Page 2 This Owner’s Manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment that are no longer available or were not ordered on this vehicle.
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..........................8 GETTING TO KNOW YOUR VEHICLE ..................12 GETTING TO KNOW YOUR INSTRUMENT PANEL ............86 SAFETY ............................112 STARTING AND OPERATING ....................157 IN CASE OF EMERGENCY ....................237 SERVICING AND MAINTENANCE ..................267 TECHNICAL SPECIFICATIONS ..................... 312 MULTIMEDIA ..........................
Page 4 INTRODUCTION VEHICLE SECURITY ALARM..........21 MIRRORS ................35 To Arm The System............21 Inside Day/Night Mirror — If Equipped ...... 35 HOW TO USE THIS MANUAL ..........9 To Disarm The System ..........21 Automatic Dimming Mirror — If Equipped ....36 Essential Information.............9 Outside Mirrors ............
Page 5 INTERIOR LIGHTS ...............42 INTERNAL EQUIPMENT ............65 INSTRUMENT CLUSTER DISPLAY........93 Courtesy Lights............42 Storage .................65 Instrument Cluster Display Controls ......93 Illuminated Entry ............44 Cupholders ..............70 Oil Life Reset..............94 Electrical Power Outlets ..........70 WINDSHIELD WIPERS AND WASHERS ......44 Display Menu Items ............
Page 6 OCCUPANT RESTRAINT SYSTEMS ........ 129 NORMAL OPERATION — DIESEL ENGINE ..... 163 POWER STEERING ............185 Occupant Restraint Systems Features ....129 Cold Weather Precautions ........163 Electric Power Steering ..........185 Important Safety Precautions ........129 Engine Idling.............. 164 FUEL SAVER TECHNOLOGY 5.7L ENGINES ONLY — IF EQUIPPED..............186 Seat Belt Systems ............
Page 7 IN CASE OF EMERGENCY PARKSENSE FRONT AND REAR PARK ASSIST ... 200 VEHICLE LOADING ............223 ParkSense Sensors........... 201 Gross Vehicle Weight Rating (GVWR) ..... 223 HAZARD WARNING FLASHERS ........237 ParkSense Warning Display ........201 Payload..............223 ASSIST AND SOS SYSTEM — IF EQUIPPED ....237 Gross Axle Weight Rating (GAWR) ......
Page 8 SERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS Body Lubrication............286 Windshield Wiper Blades ......... 286 SCHEDULED SERVICING — GASOLINE ENGINES ..267 IDENTIFICATION DATA .............312 Exhaust System ............287 Maintenance Plan............. 267 Vehicle Identification Number .........312 Cooling System ............288 SCHEDULED SERVICING — DIESEL ENGINE ....270 BRAKE SYSTEM ...............312 Charge Air Cooler —...
Page 9 MULTIMEDIA CUSTOMER ASSISTANCE UCONNECT VOICE RECOGNITION QUICK TIPS ..... 383 Introducing Uconnect ..........383 UCONNECT SYSTEMS ............. 323 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR Get Started..............383 CYBERSECURITY ............. 323 VEHICLE ................388 Basic Voice Commands..........383 UCONNECT SETTINGS ............. 323 Prepare For The Appointment ........388 Radio .................
Page 10: Introduction
INTRODUCTION Dear Customer, congratulations on selecting your new vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality. This is a specialized utility vehicle. It can go places and perform tasks that are not intended for conventional passenger vehicles. It handles and maneuvers differently from many passenger vehicles both on-road and off-road, so take time to become familiar with your vehicle.
Page 11: How To Use This Manual
HOW TO USE THIS MANUAL VAN CONVERSIONS/CAMPERS The New Vehicle Limited Warranty does not apply to body modifications or special SSENTIAL NFORMATION equipment installed by van conversion/camper manufacturers/body builders. US residents refer to the Warranty Information, Section 2.1.C. Canadian residents refer to the Consult the Table of Contents to determine which section contains the information you “What Is Not Covered”...
Page 12 Figure 1 illustrates the dimensions describing the forward and rearward limits of the zone in which the Center of Gravity (CG) of a slide-in camper must be located, to provide satisfactory vehicle handling and to prevent overload of the front and rear axles. Figure 2 illustrates a proper match between truck and camper.
Page 13: Vehicle Modifications/Alterations
When the truck is used to carry a slide-in camper, the total cargo load of the truck consists NOTE: of the manufacturer’s camper weight figure, the weight of installed additional camper These ratings are also provided on the vehicle certification label located on the driver’s equipment not included in the manufacturer’s camper weight figure, the weight of camper side B-pillar.
Page 14: Getting To Know Your Vehicle
GETTING TO KNOW YOUR VEHICLE VEHICLE USER GUIDE — IF EQUIPPED NOTE: Features/Benefits Vehicle User Guide features are not available while the  Pre-installed on your Uconnect touchscreen radio Access your Owner’s Information right through your vehicle is moving. If you try to access while the vehicle is ...
Page 15: Keys
GETTING TO KNOW YOUR VEHICLE KEYS NOTE: A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob. If the LED key fob light no longer illu- minates from key fob button pushes, then the key fob Your vehicle uses a keyless ignition system.
Page 16 GETTING TO KNOW YOUR VEHICLE Sound Horn With Remote Key Lock  You may need to be less than 35 ft (11 m) from the Canceling Remote Lowering vehicle when using the key fob to turn off the Panic Vehicle lowering can be cancelled at anytime. When This feature will cause the horn to chirp when the doors Alarm due to the radio frequency noises emitted by the vehicle lowering is cancelled, the vehicle will raise up to...
Page 17 GETTING TO KNOW YOUR VEHICLE Remove the emergency key by pushing and holding Next, locate the gap on the right side of the key fob, the release button located on the right side of the which is positioned further to the edge than the left key fob, while pulling the emergency key out with side gap.
Page 18 GETTING TO KNOW YOUR VEHICLE NOTE: This device may not cause harmful interference, and WARNING! When replacing the battery, ensure the (+) sign on the This device must accept any interference received, battery is facing upward. Avoid touching the new battery ...
Page 19: Ignition Switch
GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH START  The engine will start. EYLESS UTTON GNITION WARNING! This feature allows the driver to operate the ignition switch  When exiting the vehicle, always remove the key fob with the push of a button as long as the Remote Keyless from the vehicle and lock your vehicle.
Page 20: Remote Start - If Equipped (Gasoline)
GETTING TO KNOW YOUR VEHICLE REMOTE START — IF EQUIPPED The engine only runs in the ON/RUN ignition position or EMOTE TART BORT ESSAGE from a remote start request. (GASOLINE) One of the following messages will display in the In case the ignition switch does not change with the push instrument cluster display if the vehicle fails to remote of a button, the key fob may have a low or depleted start or exits Remote Start prematurely:...
Page 21: To Exit Remote Start Mode Without Driving The
GETTING TO KNOW YOUR VEHICLE  For security, power window and power sunroof opera- remote start is activated. These features will stay on La operación de este equipo está sujeta a las siguientes tion (if equipped) are disabled when the vehicle is in through the duration of Remote Start or until the ignition dos condiciones: the Remote Start mode.
Page 22: How To Use Remote Start
GETTING TO KNOW YOUR VEHICLE SENTRY KEY EMOTE TART CAUTION! All of the following conditions must be met before the The Sentry Key Immobilizer system prevents unauthorized The Sentry Key Immobilizer system is not compatible engine will remote start: vehicle operation by disabling the engine. The system with some aftermarket Remote Start systems.
Page 23: General Information
GETTING TO KNOW YOUR VEHICLE NOTE: La operación de este equipo está sujeta a las siguientes Perform one of the following methods to lock the dos condiciones: vehicle: Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank es posible que este equipo o dispositivo no cause ...
Page 24: Rearming Of The System
GETTING TO KNOW YOUR VEHICLE The Vehicle Security Alarm is designed to protect your WARNING! vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previously  Never leave children alone in a vehicle, or with described arming sequences has occurred, the Vehicle access to an unlocked vehicle.
Page 25: Power Side Steps - If Equipped
GETTING TO KNOW YOUR VEHICLE If the vehicle speed exceeds 5 mph (8 km/h), or if the  The key fob may not be able to be detected by the retract setting is selected in the touchscreen, the steps vehicle Passive Entry system if it is located next to a will retract.
Page 26 GETTING TO KNOW YOUR VEHICLE To Unlock From The Passenger Side: To Lock The Vehicle’s Doors: NOTE: With a valid Passive Entry key fob within 5 ft (1.5 m) of the With one of the vehicle’s Passive Entry key fobs within 5 ft ...
Page 27: Automatic Door Locks - If Equipped
GETTING TO KNOW YOUR VEHICLE Automatic Doors Unlock — If Equipped Le présent appareil est conforme aux CNR d`Innovation, Science and Economic Development applicables aux This feature unlocks all of the doors of the vehicle when appareils radio exempts de licence. L'exploitation est either front door is opened.
Page 28: Driver Memory Settings - If Equipped
GETTING TO KNOW YOUR VEHICLE DRIVER MEMORY SETTINGS — IF EQUIPPED NOTE:  Memory profiles can be set without the vehicle in This feature allows the driver to save up to two different PARK, but the vehicle must be in PARK to recall a memory profiles for easy recall through a memory switch.
Page 29: Memory Position Recall
GETTING TO KNOW YOUR VEHICLE SEATS Push and release the set (S) button on the memory switch, then within five seconds push and release the button labeled (1) or (2) accordingly. “Memory Profile Seats are a part of the Occupant Restraint System of the Set”...
Page 30: Manual Rear Seat Adjustment
GETTING TO KNOW YOUR VEHICLE Manual Front Seat Recline Adjustment 40-20-40 Front Bench Seat — If Equipped ANUAL DJUSTMENT The recline lever is located on the outboard side of the The seat is divided into three segments. The outboard seat seat.
Page 31: Power Front Seat Adjustment
GETTING TO KNOW YOUR VEHICLE Adjusting The Seat Forward Or Rearward WARNING! WARNING! The seat can be adjusted both forward and rearward. Push Do not ride with the seatback reclined so that the  Adjusting a seat while driving may be dangerous. the seat switch forward or rearward.
Page 32: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE — I Power Lumbar — If Equipped  When you place the vehicle’s ignition in the OFF posi- EATED EATS QUIPPED tion, the driver’s seat will move about 2.4 inches Vehicles equipped with power driver or passenger seats (60 mm) rearward if the driver’s seat position is greater On some models, the front and rear seats may be may be also be equipped with power lumbar.
Page 33: Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE:  Press the heated seat button a third time to turn the LO setting on.  The level of heat selected will stay on until the operator changes it.  Press the heated seat button a fourth time to turn the heating elements off.
Page 34: Plastic Grocery Bag Retainers
GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With Remote Start There are two ventilated seat switches that allow the rear WARNING! passengers to operate the seats independently. The fans On models that are equipped with remote start, the operate at three speeds: HI, MED, and LO. ...
Page 35: Rear Head Restraints
GETTING TO KNOW YOUR VEHICLE NOTE: ESTRAINTS The head restraints should only be removed by qualified The outboard head restraints are non-adjustable, but can technicians, for service purposes only. If either of the head restraints require removal, see an authorized dealer. be folded down for improved rearward visibility.
Page 36: Steering Wheel
GETTING TO KNOW YOUR VEHICLE The center head restraint is not adjustable or removable. To unlock the steering column, push the lever downward.  Press the heated steering wheel button once to To tilt the steering column, move the steering wheel turn the heating element on.
Page 37: Driver Adjustable Pedals - If Equipped
GETTING TO KNOW YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — MIRRORS to be adjusted when the system is locked out: “Adjust- able Pedal Disabled — Cruise Control Engaged” or IF EQUIPPED “Adjustable Pedal Disabled — Vehicle In Reverse”. — NSIDE IGHT IRROR NOTE: The adjustable pedals system is designed to allow a...
Page 38: Automatic Dimming Mirror - If Equipped
GETTING TO KNOW YOUR VEHICLE — — I UTOMATIC IMMING IRROR UTSIDE IRRORS OWER IRRORS QUIPPED QUIPPED To receive maximum benefit, adjust the outside mirrors to The controls for the power mirrors are located on the center on the adjacent lane of traffic with a slight overlap driver's door trim panel.
Page 39: Power Folding Outside Mirrors For Standard And
GETTING TO KNOW YOUR VEHICLE Using the mirror control switch, push on any of the four NOTE: arrows for the direction that you want the mirror to move.  The power fold mirrors are designed to operate while the vehicle is stationary or traveling at moderate speeds.
Page 40: Trailer Towing Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE — vehicle is shifted out of the REVERSE position. Each stored RAILER OWING IRRORS memory setting will have an associated Tilt Side Mirrors In QUIPPED Reverse position. NOTE: These mirrors are designed with an adjustable mirror The Tilt Side Mirrors In Reverse feature is not turned on head to provide a greater vision range when towing when delivered from the factory.
Page 41: Exterior Lights
GETTING TO KNOW YOUR VEHICLE (DRL ) — Slide-On-Rod Features Of Sun Visor — AYTIME UNNING IGHTS If Equipped QUIPPED The sun visor Slide-On-Rod feature allows for additional The headlights on your vehicle will illuminate when the flexibility in positioning the visor to block out the sun. engine is started.
Page 42: High/Low Beam Switch
GETTING TO KNOW YOUR VEHICLE  Broken, muddy, or obstructed headlights and taillights WITCH LASH of vehicles in the field of view will cause headlights to Push the multifunction lever toward the instrument panel remain on longer (closer to the vehicle). Also, dirt, film, You can signal another vehicle with your headlights by to switch the headlights to high beam.
Page 43: Headlights On With Wipers
GETTING TO KNOW YOUR VEHICLE — I NOTE: EADLIGHTS IPERS RONT IGHTS QUIPPED If either light remains on and does not flash, or there is a VAILABLE UTOMATIC To activate the front fog lights, turn on the parking lights or very fast flash rate, check for a defective outside light low beam headlights and push in the center of the bulb.
Page 44: Battery Saver
GETTING TO KNOW YOUR VEHICLE If the vehicle’s speed is 0 mph (0 km/h), these lights can NOTE: also be turned on using the switch located just inside the Battery saver mode is canceled if the ignition is placed in pickup box, on the lower part of the bed light lens.
Page 45 GETTING TO KNOW YOUR VEHICLE Courtesy/Reading Lights The overhead console lights can also be operated individually as reading lights by pushing the corresponding buttons. Push Lens On/Off Rear Courtesy Light Dimmer Controls NOTE: 1 — Ambient Light Control The courtesy/reading lights will remain on until the switch 2 —...
Page 46: Illuminated Entry
GETTING TO KNOW YOUR VEHICLE If the washer knob is depressed while in the delay range, LLUMINATED NTRY the wipers will operate for several seconds after the The courtesy lights will turn on when you use the key fob washer knob is released. It will then resume the to unlock the doors or open any door.
Page 47: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE CLIMATE CONTROLS — I The Rain Sensing system has protection features for the ENSING IPERS QUIPPED wiper blades and arms, and will not operate under the This feature senses rain and snowfall on the windshield following conditions: The Climate Control System allows you to regulate the and automatically activates the wipers for the driver.
Page 48 GETTING TO KNOW YOUR VEHICLE Icon Description MAX A/C Setting Rotate the temperature control knob until it is set to MAX A/C. This is the coldest setting and puts the A/C to maximum power. A/C Button Push the A/C button to engage the Air Conditioning (A/C). Recirculation Button Push the button on the faceplate to change the system between recirculation mode and outside air mode.
Page 49 GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Page 50: Automatic Climate Control Overview
GETTING TO KNOW YOUR VEHICLE UTOMATIC LIMATE ONTROL VERVIEW NOTE: Icons and descriptions can vary based upon vehicle equipment. Uconnect 4/4C/4C NAV With 8.4–inch Display Automatic Uconnect 4C NAV With 12–inch Display Automatic Temperature Controls Temperature Controls Icon Description MAX A/C Press and release to change the current setting.
Page 51 GETTING TO KNOW YOUR VEHICLE Icon Description Recirculation Button Press and release this button to change the system between recirculation mode and outside air mode. The Recirculation indicator and the A/C indicator illuminate when Recirculation mode is turned on. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.
Page 52 GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Temperature Knobs Driver and Passenger Temperature Control Temperature control provides the driver and passenger with independent temperature control. Push the red button (or rotate knob if equipped) on the faceplate or touchscreen, or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings. Push the blue button (or rotate knob if equipped) on the faceplate or touchscreen, or press and slide the temperature bar towards the blue arrow button on the touchscreen for cooler temperature settings.
Page 53 GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Blower Knob Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen.
Page 54: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
Page 55: Automatic Temperature Control (Atc)
GETTING TO KNOW YOUR VEHICLE Recirculation Winter Operation NOTE:  It is not necessary to move the temperature settings for In cold weather, use of Recirculation mode may lead to To ensure the best possible heater and defroster cold or hot vehicles. The system automatically adjusts excessive window fogging.
Page 56: Windows
GETTING TO KNOW YOUR VEHICLE The power window controls located on the driver's door WEATHER CONTROL SETTINGS CAUTION! trim panel have up-down switches that give you fingertip control of all power windows. There is a single opening and Turn on and set the ...
Page 57: Wind Buffeting
GETTING TO KNOW YOUR VEHICLE To stop the window from going all the way down during the Pull the window switch up to close the window Auto-Down operation, pull up on the switch briefly. completely and continue to hold the switch up for an additional two seconds after the window is closed.
Page 58: Power Sunroof - If Equipped
GETTING TO KNOW YOUR VEHICLE POWER SUNROOF — IF EQUIPPED Manual Mode WARNING! To open the sunroof, push and hold the switch rearward. —  Never leave children unattended in a vehicle, or with The sunroof will move rearward and automatically stop at INGLE OWER UNROOF...
Page 59: Dual Pane Power Sunroof - If Equipped
GETTING TO KNOW YOUR VEHICLE — Sunshade Operation NOTE: OWER UNROOF Ignition Off time is programmable through the Uconnect The sunshade can be opened manually. However, the QUIPPED System. Refer to “Uconnect Settings” in “Multimedia” for sunshade will open automatically as the sunroof opens. further information.
Page 60 GETTING TO KNOW YOUR VEHICLE Express Express Close operation, any other actuation of the switch WARNING! will stop the sunroof. Push the switch rearward and release it within one-half  Never leave children unattended in a vehicle, or with second, the sunroof will open to the comfort stop position Manual access to an unlocked vehicle.
Page 61: Hood
GETTING TO KNOW YOUR VEHICLE Closing Power Sunshade Pinch Protect Feature Ignition Off Operation If the sunroof is open or vented the sunshade cannot be This feature will detect an obstruction in the closing of the The power sunroof switch will remain active for up to closed beyond the half open position.
Page 62: To Close The Hood
GETTING TO KNOW YOUR VEHICLE Pull the hood release lever located below the For the tailgate to lower, the vehicle must be: CAUTION! steering wheel at the base of the instrument panel.  In PARK or NEUTRAL To prevent possible damage, do not slam the hood to Reach into the opening beneath the center of the ...
Page 63: Garage Door Opener - If Equipped
GETTING TO KNOW YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED Opening Closing The tailgate must be latched closed to open the swing Always close the narrower swing door first, then close the HomeLink® replaces up to three hand-held transmitters doors.
Page 64: Before You Begin Programming Homelink
GETTING TO KNOW YOUR VEHICLE Programming A Rolling Code EFORE EGIN ROGRAMMING WARNING! ® For programming garage door openers that were  Your motorized door or gate will open and close while manufactured after 1995. These garage door openers can you are programming the universal transceiver.
Page 65 GETTING TO KNOW YOUR VEHICLE Place the ignition in the ON/RUN position. NOTE: Continue to hold both buttons and observe the indicator light. The HomeLink® indicator will flash If the garage door opener/device does not activate, push Place the hand-held transmitter 1 to 3 inches (3 to slowly and then rapidly after HomeLink®...
Page 66: Canadian/Gate Operator Programming
GETTING TO KNOW YOUR VEHICLE Press and hold the programmed HomeLink® button ANADIAN PERATOR ECURITY and observe the indicator light. ROGRAMMING It is advised to erase all channels before you sell or turn in NOTE: your vehicle. For programming transmitters in Canada/United States ...
Page 67: General Information
GETTING TO KNOW YOUR VEHICLE l'utilisateur de l'appareil doit accepter tout brouillage WARNING! radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.  Your motorized door or gate will open and close while you are programming the universal transceiver. Do La operación de este equipo está...
Page 68 GETTING TO KNOW YOUR VEHICLE Door Storage WARNING! Front Door Storage — If Equipped  This armrest is not a seat. Anyone seated on the Storage areas are located in the door trim panels. armrest could be seriously injured during vehicle operation, or a collision.
Page 69 GETTING TO KNOW YOUR VEHICLE Push the release button at the front of the cupholder bin to slide tray rearward for access of front lower storage bin, or forward to access the rear lower storage bin with the center console lid in the open position. Center Console Tandem Doors—...
Page 70 GETTING TO KNOW YOUR VEHICLE Rear Console Storage — If Equipped If vehicle is equipped with “Smart Fold”, the center portion of the 40/20/40 rear seat will fold forward for rear seat cupholders and a storage compartment. Lift up on the console latch to access.
Page 71 GETTING TO KNOW YOUR VEHICLE Each storage bin also contains two hooks for securing cargo. These hooks should be used to secure loads safely when the vehicle is moving. Rotate Lock Mechanism Flip Inside Of Base Upward In-Floor Storage Bin Hooks NOTE: The maximum load limit for each hook is 250 lb (113 kg).
Page 72: Cupholders
GETTING TO KNOW YOUR VEHICLE If your vehicle is equipped with “Smart Fold”, the entire UPHOLDERS center section of the 40/20/40 seat folds forward for Front Seat Cupholders access of cupholders and console storage. For vehicles equipped with a center console, two cupholders are located in front of the console storage bin.
Page 73 GETTING TO KNOW YOUR VEHICLE CAUTION! WARNING!  Do not exceed the maximum power of 160 Watts  Close the lid when not in use and while driving the (13 Amps) at 12 Volts. If the 160 Watts (13 Amps) vehicle.
Page 74: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE — I OWER NVERTER QUIPPED If equipped, a 115 Volt (400 Watts Maximum) inverter may be located inside the center console towards the right hand side, just under the Wireless Charging Pad (if equipped). This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 Watts.
Page 75: Wireless Charging Pad - If Equipped
GETTING TO KNOW YOUR VEHICLE — IRELESS HARGING CAUTION! QUIPPED The key fob should not be placed on the charging pad or within 15 cm (150 mm) of it. Doing so can cause excessive heat buildup and damage to the fob. Placing the fob in close proximity of the charging pad blocks the fob from being detected by the vehicle and prevents the vehicle from starting.
Page 76: Pickup Box
GETTING TO KNOW YOUR VEHICLE PICKUP BOX RAMBOX — IF EQUIPPED WARNING! The pickup box has many features designed for utility and The RamBox system is an integrated pickup box storage  The pickup box is intended for load carrying purposes convenience.
Page 77: Rambox Safety Warning
GETTING TO KNOW YOUR VEHICLE Always return the key to the upright (vertical) position CAUTION! CAUTION! before removing it from the keyhole. Failure to follow the following items could cause Leaving the lid open for extended periods of time could CAUTION! damage to the vehicle: cause the vehicle battery to discharge.
Page 78: Bed Divider - If Equipped
GETTING TO KNOW YOUR VEHICLE — I With the side gates open, position the divider fully IVIDER QUIPPED WARNING! forward in the bed against the front panel. The bed divider has two functional positions:  Do not drive the vehicle with the storage bin covers open.
Page 79 GETTING TO KNOW YOUR VEHICLE Rotate the center handle horizontally to secure the To install the bed divider into a divider position, perform side gates in the closed position. the following: Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the divider side gates.
Page 80: Bed Rail Tie-Down System - If Equipped
GETTING TO KNOW YOUR VEHICLE — Each cleat must be located and tightened down in one of Cleat Removal (Standard Box Rail) YSTEM the detents, along either rail, in order to keep cargo To remove the cleats from the utility rail, slide the cleat QUIPPED properly secure.
Page 81: Easy-Off Tailgate
GETTING TO KNOW YOUR VEHICLE EASY-OFF TAILGATE Cleat Removal (Without Tonneau Cover) NOTE: Rest the tailgate on the bumper so that the entire tailgate Remove the end cap by pushing upward on the release is secure and supported. To simplify mounting of a camper unit with an overhang, button located beneath the end cap while pulling the cap the tailgate can be removed.
Page 82 GETTING TO KNOW YOUR VEHICLE Remove the connector bracket from the sill by pushing inward in the locking tab. Connected Wiring Harness Body Side Plug (One Piece) 1 — First Release Tab Connect the tailgate plugs (provided in the glove compartment) to the tailgate wiring harness to Connector Bracket Location 2 —...
Page 83: Locking Tailgate
GETTING TO KNOW YOUR VEHICLE Tape the tailgate harness and bracket against the WARNING! forward-facing surface of the tailgate. This will prevent damaging the connector and bracket when To avoid inhaling carbon monoxide, which is deadly, the storing or reinstalling the tailgate. exhaust system on vehicles equipped with “Cap or Slide-In Campers”...
Page 84 GETTING TO KNOW YOUR VEHICLE Pull Handle Downward Stowed Position Third Panel Position (Tri-Folded) Lift up on the third panel and fold it onto the second Once in the third panel position, repeat steps “1” and panel. “2” on the front set of clamps. NOTE: When folding the second and third panels, the sections MUST be held together to avoid damage to the cover...
Page 85: Tri-Fold Tonneau Cover Installation
GETTING TO KNOW YOUR VEHICLE With two people, remove the cover. NOTE:  Be sure the Tonneau Cover has been folded completely, and the stowage straps are engaged, before removing.  You can drive the vehicle with a fully folded Tonneau Cover.
Page 86 GETTING TO KNOW YOUR VEHICLE Holding the lower end of the clamp, push it to the Completely unfold the Tonneau Cover. center and pull up. Push the handle firmly and listen NOTE: for a clicking sound to confirm the clamps are set to When unfolding the center and rear panels, the sections the Clamped Position.
Page 87: Tri-Fold Tonneau Cover Cleaning
GETTING TO KNOW YOUR VEHICLE NOTE: Repeat steps “2” through “3” for the rear pair of ONNEAU OVER LEANING clamps. Unfold the panel gently. It is not recommended to allow For proper cleaning of the Tonneau Cover, use Mopar® the panels to drop under their own weight. Whitewall &...
Page 88: Getting To Know Your Instrument Panel
GETTING TO KNOW YOUR INSTRUMENT PANEL BASE / MIDLINE INSTRUMENT CLUSTER — GASOLINE Base / Midline Instrument Cluster — Gasoline...
Page 89: Base / Midline Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Pressure Gauge IDLINE NSTRUMENT LUSTER WARNING!  The pointer should always indicate the oil pres- ESCRIPTIONS A hot engine cooling system is dangerous. You or others sure when the engine is running. A continuous could be badly burned by steam or boiling coolant.
Page 90: Premium Instrument Cluster - Gasoline
GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER — GASOLINE Premium Instrument Cluster Display — Gasoline...
Page 91: Premium Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL Temperature Gauge REMIUM NSTRUMENT LUSTER CAUTION!  The pointer shows engine coolant temperature. ESCRIPTIONS Driving with a hot engine cooling system could damage The pointer positioned within the normal range your vehicle. If the temperature gauge reads “H”, pull indicates that the engine cooling system is oper- Tachometer over and stop the vehicle.
Page 92: Base / Midline Instrument Cluster - Diesel
GETTING TO KNOW YOUR INSTRUMENT PANEL BASE / MIDLINE INSTRUMENT CLUSTER — DIESEL Base / Midline Instrument Cluster — Diesel Engine Coolant Temperature Warning Light turns on while driving, safely bring the NSTRUMENT LUSTER ESCRIPTIONS vehicle to a stop, and turn off the engine. DO NOT ...
Page 93 GETTING TO KNOW YOUR INSTRUMENT PANEL Speedometer NOTE: WARNING!  Indicates vehicle speed.  The gauge may take up to five seconds to update A hot engine cooling system is dangerous. You or others after adding a gallon or more of Diesel Exhaust Diesel Exhaust Fluid (DEF) Gauge could be badly burned by steam or boiling coolant.
Page 94: Premium Instrument Cluster - Diesel
GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER — DIESEL Premium Instrument Cluster — Diesel...
Page 95: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL  The gauge may take up to five seconds to update your vehicle’s systems and features. Using a driver NSTRUMENT LUSTER ESCRIPTIONS after adding a gallon or more of Diesel Exhaust interactive display located on the instrument panel, your Tachometer Fluid (DEF) to the DEF tank.
Page 96: Oil Life Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL The instrument cluster display menu items may consist of Up And Down Arrow Buttons: ESET the following: Using the up or down arrow button allow you to cycle Your vehicle is equipped with an engine oil change ...
Page 97: Display Menu Items
GETTING TO KNOW YOUR INSTRUMENT PANEL Push and release the up or down arrow button to exit  Oil Pressure — If Equipped ACC SET the submenu screen.  Battery Voltage — If Equipped When ACC is set, the set speed will display in the instrument cluster.
Page 98 GETTING TO KNOW YOUR INSTRUMENT PANEL Trip Info Audio Push and release the up or down arrow button until the Screen Setup Menu Icon/Title is highlighted in the Push and release the up or down arrow button until the Push and release the up or down arrow button until the instrument cluster display.
Page 99 GETTING TO KNOW YOUR INSTRUMENT PANEL  Transmission Temperature – If Equipped  Trailer Trip – If Equipped Lower Left – If Equipped  Oil Life – If Equipped  Trailer Brake – If Equipped  None  Oil Pressure – If Equipped ...
Page 100: Diesel Particulate Filter (Dpf) Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL  Trip A Distance Odometer  Exhaust Filter XX% Full Safely Drive at Highway Speeds to Remedy — This message will be displayed in the  Trip B Distance  No Decimal Point (Default) instrument cluster if the exhaust particulate filter ...
Page 101: Displays
GETTING TO KNOW YOUR INSTRUMENT PANEL  Exhaust Filter Full Safely Drive at Highway Speeds To  Engine Will Not Restart in XXXX mi DEF Low Refill CAUTION! Remedy Soon — This message will display when DEF driving range is less than 500 miles, DEF fluid top off is See an authorized dealer, as damage to the exhaust ...
Page 102: Diesel Exhaust Fluid (Def) Fault Warning Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL (DEF) F displayed mileage. The message will be displayed IESEL XHAUST LUID AULT ATTERY AVER ATTERY AVER during vehicle start up with an updated distance — E ARNING ESSAGES ESSAGE LECTRICAL mileage, and it will be accompanied by a single chime. Starting at 100 miles, remaining range will be continu- —...
Page 103: Warning Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL The electrical loads that may be switched off (if equipped),  The battery was used for an extended period with the indicative and precautionary and as such must not be and vehicle functions which can be affected by load engine not running to supply radio, lights, chargers, considered as exhaustive and/or alternative to the reduction:...
Page 104 GETTING TO KNOW YOUR INSTRUMENT PANEL Brake Warning Light Vehicle Security Warning Light — WARNING! If Equipped This warning light monitors various brake Driving a vehicle with the red brake light on is functions, including brake fluid level and This light will flash at a fast rate for dangerous.
Page 105 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Pressure Warning Light Transmission Temperature Warning If the light continues to flash when the vehicle is running, immediate service is required and you may experience Light — If Equipped This warning light will illuminate to indicate low reduced performance, an elevated/rough idle, or engine engine oil pressure.
Page 106: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Active When the engine is running, the MIL may flash to alert ELLOW ARNING IGHTS serious conditions that could lead to immediate loss of Warning Light — If Equipped Adaptive Cruise Control (ACC) Fault power or severe catalytic converter damage.
Page 107 GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Warning Light — If Equipped Low Fuel Warning Light on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for The LaneSense system provides the driver with When the fuel level reaches approximately those tires.
Page 108: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Speed Control Fault Warning Light wheels on your vehicle to ensure that the replacement or If the ABS light does not turn on when the ignition is placed alternate tires and wheels allow the TPMS to continue to in the ON/RUN or ACC/ON/RUN position, have the brake This warning light will illuminate to indicate the function properly.
Page 109 GETTING TO KNOW YOUR INSTRUMENT PANEL TOW/HAUL Indicator Light Air Suspension Normal Height Indicator Air Suspension Ride Height Lowering Light — If Equipped Indicator Light — If Equipped This indicator light will illuminate when TOW/ HAUL mode is selected. This light will illuminate when the air This light will blink and alert the driver that the suspension system is set to the Normal setting.
Page 110: Green Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 4WD High Indicator Light — If Equipped Water In Fuel Indicator Light — If Equipped Adaptive Cruise Control (ACC) Set With No Target Detected Indicator Light — This light alerts the driver that the vehicle is in The “Water In Fuel Indicator Light”...
Page 111: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Front Fog Indicator Light — If Equipped Stop/Start Active Indicator Light — Cruise Control Ready Indicator If Equipped This indicator light will illuminate when the This indicator light will illuminate when the front fog lights are on. cruise control is ready, but not set.
Page 112: Blue Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Indicator Light — If Equipped If any of these systems require service, the OBD II system WARNING! will turn on the Malfunction Indicator Light (MIL). It will When the LaneSense system is ON, but not also store diagnostic codes and other information to ...
Page 113: Emissions Inspection And Maintenance
GETTING TO KNOW YOUR INSTRUMENT PANEL EMISSIONS INSPECTION AND As soon as you cycle the ignition switch to the ON If your OBD II system is not ready, you should see an position, you will see the “Malfunction Indicator Light authorized dealer or repair facility.
Page 114: Safety
SAFETY SAFETY FEATURES ABS is designed to function with the Original Equipment WARNING! Manufacturer (OEM) tires. Modification may result in degraded ABS performance. (ABS)  The ABS contains sophisticated electronic equip- RAKE YSTEM ment that may be susceptible to interference caused Anti-Lock Brake Warning Light by improperly installed or high output radio transmit- The Anti-Lock Brake System (ABS) provides increased...
Page 115: Electronic Brake Control (Ebc) System
SAFETY (EBC) Electronic Roll Mitigation (ERM) LECTRONIC RAKE ONTROL WARNING! The Electronic Roll Mitigation (ERM) system anticipates YSTEM The Brake Assist System (BAS) cannot prevent the the potential for wheel lift by monitoring the driver’s natural laws of physics from acting on the vehicle, nor Your vehicle is equipped with an advanced Electronic steering wheel input and the speed of the vehicle.
Page 116 SAFETY Electronic Stability Control (ESC) ESC Operating Modes WARNING! NOTE: The Electronic Stability Control (ESC) system enhances  Electronic Stability Control (ESC) cannot prevent the directional control and stability of the vehicle under Depending upon model and mode of operation, the ESC natural laws of physics from acting on the vehicle, various driving conditions.
Page 117 SAFETY The “ESC Activation/Malfunction Indicator Light” (located WARNING! WARNING! in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active.  When in “Partial Off” mode, the TCS functionality of  In the ESC “Full Off” mode, the engine torque reduc- The “ESC Activation/Malfunction Indicator Light”...
Page 118 SAFETY HDC Has Three States:  3rd = 1.8 mph (3 km/h) Disabling HDC Off (feature is not enabled and will not activate).  4th = 2.5 mph (4 km/h) HDC will be deactivated and disabled if any of the following conditions occur: Enabled (feature is enabled and ready but activation ...
Page 119 SAFETY WARNING! WARNING! WARNING! HDC is only intended to assist the driver in controlling There may be situations where the Hill Start Assist  HSA is not a parking brake. Always apply the parking vehicle speed when descending hills. The driver must (HSA) will not activate and slight rolling may occur, such brake fully when exiting your vehicle.
Page 120: Auxiliary Driving Systems
SAFETY Push the “ESC OFF” switch located in the lower switch NOTE: bank below the climate control four times within 20 TSC cannot stop all trailers from swaying. Always use seconds. The “ESC OFF Indicator Light” should turn caution when towing a trailer and follow the trailer tongue on and turn off two times.
Page 121 SAFETY warning indicator lamps when a motorcycle or any If the blockage message is still present after cycling the small object remains at the side of the vehicle for ignition and driving in traffic, check again for a blockage. extended periods of time (more than a couple of The BSM system notifies the driver of objects in the seconds).
Page 122 SAFETY Overtaking Traffic The BSM system is designed not to issue an alert on WARNING! stationary objects such as guardrails, posts, walls, foliage, If you pass another vehicle slowly with a relative speed berms, snow banks, car washes, etc. However, The Blind Spot Monitoring system is only an aid to help less than 15 mph (24 km/h) and the vehicle remains in occasionally the system may alert on such objects.
Page 123 SAFETY RCP monitors the rear detection zones on both sides of Blind Spot Alert Lights Only NOTE: the vehicle, for objects that are moving toward the side of The BSM system will store the current operating mode When operating in Blind Spot Alert mode, the BSM system the vehicle with a minimum speed of approximately 3 mph when the vehicle is shut off.
Page 124 SAFETY Automatic Trailer Detection Maximum length supported by the Trailer Merge Assist  Trailer length between 10 ft to 20 ft (3 m to 6 m) — feature is 39.5 ft (12 m). Trailer length is considered the Blind spot zone will be adjusted to 20 ft (6 m) There are two modes of operation for the detection of the forward most portion of the trailer hitch to the rearward trailer length:...
Page 125: Forward Collision Warning (Fcw) With Mitigation - If Equipped
SAFETY La operación de este equipo está sujeta a las siguientes to the warnings by braking and the system determines WARNING! dos condiciones: that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the system will The Blind Spot Monitoring system is only an aid to help es posible que este equipo o dispositivo no cause compensate and provide additional brake force as...
Page 126 SAFETY Turning FCW On or Off FCW Braking Status And Sensitivity NOTE:  The minimum speed for FCW activation is 3 mph The FCW button is located in the Uconnect display in the The FCW Sensitivity and Active Braking status are (5 km/h).
Page 127: Tire Pressure Monitoring System (Tpms)
SAFETY FCW Limited Warning Le présent appareil est conforme aux CNR d`Innovation, values in a different color, or the Uconnect radio will Science and Economic Development applicables aux display a TPMS message, when this occurs you must If the instrument cluster displays “ACC/FCW Limited appareils radio exempts de licence.
Page 128 SAFETY The vehicle may need to be driven for up to 20 minutes CAUTION! above 15 mph (24 km/h) in order for the TPMS to receive this information.  Using aftermarket tire sealants may cause the Tire NOTE: Pressure Monitoring System (TPMS) sensor to become inoperable.
Page 129 SAFETY Tire Pressure Monitoring Low Pressure 20 minutes above 15 mph (24 km/h) in order for the  Using wheels/tires not equipped with TPMS sensors TPMS to receive this information. Warnings A system fault may occur due to an incorrect TPMS sensor NOTE: location condition.
Page 130 SAFETY General Information 75 seconds and then remain on solid. In addition, the  The Tire Fill Alert feature cannot be entered if an instrument cluster will display a "SERVICE TPM existing TPMS fault is set to “active” or if the system is The following regulatory statement applies to all Radio SYSTEM"...
Page 131: Occupant Restraint Systems
SAFETY OCCUPANT RESTRAINT SYSTEMS If a child from 2 to 12 years old (not in a rear-facing WARNING! child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the Some of the most important safety features in your vehicle ...
Page 132 SAFETY Initial Indication The outboard front passenger seat BeltAlert is not active WARNING! when the outboard front passenger seat is unoccupied. If the driver is unbuckled when the ignition switch is first in BeltAlert may be triggered when an animal or other items ...
Page 133 SAFETY plate and pull out the seat belt. Slide the latch plate WARNING! WARNING! up the webbing as far as necessary to allow the seat belt to go around your lap.  Two people should never be belted into a single seat ...
Page 134 SAFETY Position the lap belt so that it is snug and lies low Position the latch plate as close as possible to the As a guide, if you are shorter than average, you will prefer across your hips, below your abdomen. To remove anchor point.
Page 135 SAFETY Seat Belt Extender Seat Belts And Pregnant Women Seat Belt Pretensioner If a seat belt is not long enough to fit properly, even when The front outboard seat belt system is equipped with the webbing is fully extended and the adjustable upper pretensioning devices that are designed to remove slack shoulder belt anchorage (if equipped) is in its lowest from the seat belt in the event of a collision.
Page 136: Supplemental Restraint Systems (Srs)
SAFETY Switchable Automatic Locking Retractors In Automatic Locking Mode, the shoulder belt is How To Disengage The Automatic Locking Mode automatically pre-locked. The seat belt will still retract to (ALR) Unbuckle the combination lap/shoulder belt and allow it remove any slack in the shoulder belt. Use the Automatic to retract completely to disengage the Automatic Locking The seat belts in the passenger seating positions are Locking Mode anytime a child restraint is installed in a...
Page 137 SAFETY The air bag system must be ready to protect you in a The ORC turns on the Air Bag Warning Light in the WARNING! collision. The Occupant Restraint Controller (ORC) instrument panel for approximately four to eight seconds monitors the internal circuits and interconnecting wiring for a self-check when the ignition switch is first in the ON/ Ignoring the Air Bag Warning Light in your instrument associated with the electrical Air Bag System...
Page 138 SAFETY Front Air Bags This vehicle may be equipped with driver and/or front WARNING! passenger seat track position sensors that may adjust the This vehicle has front air bags and lap/shoulder belts for inflation rate of the Advanced Front Air Bags based upon ...
Page 139 SAFETY Front Air Bag Operation Occupant Classification System (OCS) — The OCS will NOT prevent deployment of the Passenger Advanced Front Air Bag. The OCS may reduce the inflation Front Passenger Seat Front Air Bags are designed to provide additional rate of the Passenger Advanced Front Air Bag if the OCS protection by supplementing the seat belts.
Page 140 SAFETY  Sitting in the center of the seat with their feet comfort- OCS is working improperly. Decreasing the front WARNING! ably on or near the floor passenger’s seated weight on the front passenger seat may result in a reduced-power deployment of the ...
Page 141 SAFETY The OCS determines the front passenger’s most probable WARNING! classification. If an occupant in the front passenger seat is seated improperly, the occupant may provide an output  If a child restraint system, child, small teenager or signal to the OCS that is different from the occupant’s adult in the front passenger seat is seated improp- properly seated weight input, for example: erly, the occupant may provide an output signal to...
Page 142 SAFETY Supplemental Side Air Bags If the Air Bag Warning Light does not come on, or stays WARNING! on after you start the vehicle, or it comes on as you drive, Supplemental Seat-Mounted Side Air Bags (SABs)  Unapproved modifications or service procedures to take the vehicle to an authorized dealer for service This vehicle is equipped with Supplemental Seat-Mounted the passenger seat assembly, its related compo-...
Page 143 SAFETY The SABIC deploys downward, covering the side windows. impact events. The system is calibrated to deploy the Side WARNING! An inflating SABIC pushes the outside edge of the headliner Air Bags on the impact side of the vehicle during impacts out of the way and covers the window.
Page 144 SAFETY If A Deployment Occurs deployment is appropriate, the rollover sensing system will WARNING! deploy the side air bags and seat belt pretensioners on The front air bags are designed to deflate immediately both sides of the vehicle.  Side Air Bags need room to inflate. Do not lean after deployment.
Page 145 SAFETY Enhanced Accident Response System Do not drive your vehicle after the air bags have deployed. Your vehicle may also be designed to perform any of these If you are involved in another collision, the air bags will not other functions in response to the Enhanced Accident Reset Procedure be in place to protect you.
Page 146: Child Restraints
SAFETY These data can help provide a better understanding of the WARNING! WARNING! circumstances in which crashes and injuries occur. In a collision, an unrestrained child can become a  Do not attempt to modify any part of your air bag NOTE: projectile inside the vehicle.
Page 147 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger and who have Either an Infant Carrier or a Convertible Child Restraint, Infants and Toddlers not reached the height or weight limits of their child facing rearward in a rear seat of the vehicle...
Page 148 SAFETY Children Too Large For Booster Seats convertible child seat. Children should remain in a WARNING! forward-facing child seat with a harness for as long as Children who are large enough to wear the shoulder belt possible, up to the highest weight or height allowed by the Do not install a rear-facing car seat using a rear support comfortably, and whose legs are long enough to bend over child seat.
Page 149 SAFETY WARNING! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly. Recommendations For Attaching Child Restraints Use Any Attachment Method Shown With An “X”...
Page 150 SAFETY LATCH Positions For Installing Child Restraints In This Vehicle Crew Cab Full Bench, Quad Cab Full Bench And 60/40 Split Bench LATCH Positions Top Tether Anchorage Symbol Crew Cab 60/40 Split Bench LATCH Positions Lower Anchorage Symbol (2 Anchorages Per Seating Position) Top Tether Anchorage Symbol Lower Anchorage Symbol (2 Anchorages Per Seating Position)
Page 151 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Never “share” a LATCH anchorage with two or more child restraints. If the Can two child restraints be attached using a common lower LATCH center position does not have dedicated LATCH lower anchorages, use anchorage? the seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in an outboard position.
Page 152 SAFETY Center Seat LATCH Always follow the directions of the child restraint Tighten all of the straps as you push the child manufacturer when installing your child restraint. Not all restraint rearward and downward into the seat. All Quad Cabs Or Crew Cab Full Bench Rear Seat: No child restraint systems will be installed as described here.
Page 153 SAFETY Lap/Shoulder Belt Systems For Installing The seat belts in the passenger seating positions are WARNING! equipped with a Switchable Automatic Locking Retractor Child Restraints In This Vehicle (ALR) that is designed to keep the lap portion of the seat ...
Page 154 SAFETY Installing A Child Restraint With A Installing Child Restraints Using The Top Pull on the webbing to make the lap portion tight against the child seat. Switchable Automatic Locking Retractor Tether Anchorage To lock the seat belt, pull down on the shoulder part (ALR): of the belt until you have pulled all the seat belt WARNING!
Page 155 SAFETY Right Or Left Outboard Seats: Attach the hook to the center tether strap loop (see Center Seat: diagram). Tighten the tether strap according to the Reach between the rear seat and rear glass to Reach between the rear seat and rear glass to child seat manufacturer’s instructions.
Page 156: Transporting Pets
SAFETY Pass the tether strap hook over the headrest behind Installing Three Child Restraints: WARNING! the child seat, through the tether strap loop behind Place a child restraint on each outboard rear seat. the seat and over to the right or left outboard tether ...
Page 157: Exhaust Gas
SAFETY Air Bag Warning Light The best protection against carbon monoxide entry into WARNING! the vehicle body is a properly maintained engine exhaust The Air Bag warning light will turn on for four to eight system.  It is extremely dangerous to ride in a cargo area, seconds as a bulb check when the ignition switch is first inside or outside of a vehicle.
Page 158: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY ERIODIC AFETY HECKS HOULD WARNING! WARNING! UTSIDE EHICLE An improperly attached, damaged, folded, or stacked  ONLY use the passenger’s side floor mat on the floor mat, or damaged floor mat fasteners may cause passenger’s side floor area. Tires your floor mat to interfere with the accelerator, brake, or ...
Page 159: Starting And Operating
STARTING AND OPERATING STARTING THE ENGINE — GASOLINE -N-G — I EYLESS NTER GNITION WARNING! ENGINES This feature allows the driver to operate the ignition switch  Do not leave children or animals inside parked vehi- with the push of a button, as long as the Remote Start/ cles in hot weather.
Page 160 STARTING AND OPERATING If the gear selector is not in PARK, the ENGINE Push the ENGINE START/STOP button a second time If the vehicle is not in PARK and the driver turns off the START/STOP button must be held for two seconds or to place the ignition to the RUN mode.
Page 161 STARTING AND OPERATING NOTE: Additional customer warnings will be given when all of WARNING! these conditions are met: In some cases the ParkSense graphic will be displayed in the instrument cluster, causing the “AutoPark Engaged  Do not attempt to push or tow your vehicle to get it ...
Page 162: Cold Weather Operation
STARTING AND OPERATING EATHER PERATION ELOW UTOMATIC RANSMISSION WARNING! –22°F O −30°C) Start the engine with the transmission gear selector in the  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave PARK (P) position.
Page 163 STARTING AND OPERATING AutoPark — Rotary Shifter and 8-Speed NOTE: The ignition will remain in the ACC mode until the gear selector is in PARK and the button is pushed twice to A delay of the start, up to five seconds is possible under Transmission Only the OFF mode.
Page 164: Extreme Cold Weather
STARTING AND OPERATING If the vehicle is not in PARK and the driver turns off the Shift to P then Shift to Gear” to not be seen. In these until you shift the vehicle into PARK or the Driver’s Door is engine, the vehicle may AutoPark.
Page 165: Starting Fluids
STARTING AND OPERATING NORMAL OPERATION — DIESEL ENGINE Fuel Operating Range TARTING LUIDS NOTE: The engine is equipped with a glow plug preheating Observe the following when the diesel engine is operating. Use “Ultra Low Sulfur Diesel Fuels (ULSD)” ONLY. system.
Page 166: Engine Idling
STARTING AND OPERATING Winter Front Cover Engine Warm-Up NOTE:  Use of Climatized ULSD Fuel or Number 1 ULSD Fuel Avoid full throttle operation when the engine is cold. When results in a noticeable decrease in fuel economy. starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the ...
Page 167: Stopping The Engine
STARTING AND OPERATING TOPPING NGINE After full load operation, idle the engine for a few minutes before shutting it down. This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger. NOTE: Refer to the following chart for proper engine shutdown. Driving Condition Load Turbocharger Temperature...
Page 168: Engine Block Heater (If Equipped)
STARTING AND OPERATING Do Not Operate The Engine With Failed To ensure reliable starting at these temperatures, use of CAUTION! an externally powered electric engine block heater Parts (available from an authorized dealer) is recommended. Never use Non-Detergent Oil or Straight Mineral Oil in All engine failures give some warning before the parts fail.
Page 169: Parking Brake
STARTING AND OPERATING NOTE: You can engage the park brake in two ways: NOTE: Light duty operation such as light trailer towing or no load The EPB fault light will illuminate if the EPB switch is held  Manually, by applying the park brake switch. operation will extend the time before the engine is at full for longer than 20 seconds in either the released or ...
Page 170 STARTING AND OPERATING In this event, urgent service of the electric park brake WARNING! CAUTION! system is required. Do not rely on the parking brake to hold the vehicle stationary.  Never use the PARK position as a substitute for the If the Brake System Warning Light remains on with the parking brake.
Page 171: Automatic Transmission
STARTING AND OPERATING Brake Service Mode WARNING! WARNING! We recommend having your brakes serviced by an You can be badly injured working on or around a motor  It is dangerous to shift out of PARK or NEUTRAL if the authorized dealer.
Page 172: Ignition Park Interlock
STARTING AND OPERATING NOTE: NOTE: WARNING! The transmission is NOT locked in PARK when the ignition In the event of a mismatch between the gear selector is in the ACC mode (even though the engine will be off). position and the actual transmission gear (for example, ...
Page 173 STARTING AND OPERATING When parking on a hill, apply the parking brake before WARNING! shifting the transmission to PARK. As an added precaution, turn the front wheels toward the curb on a  It is dangerous to shift out of PARK or NEUTRAL if the downhill grade and away from the curb on an uphill grade.
Page 174 STARTING AND OPERATING NEUTRAL (N) When frequent transmission shifting occurs (such as WARNING! when operating the vehicle under heavy loading Use this range when the vehicle is standing for prolonged conditions, in hilly terrain, traveling into strong head  Do not leave the key fob in or near the vehicle (or in periods with the engine running.
Page 175 STARTING AND OPERATING In the event of a momentary problem, the transmission transmission gear limit to 4 (fourth gear), the transmission WARNING! can be reset to regain all forward gears by performing the will not shift above fourth gear (except to prevent engine following steps: overspeed), but will shift through the lower gears normally.
Page 176: Four-Wheel Drive Operation - If Equipped
STARTING AND OPERATING The “TOW/HAUL Indicator Light” will illuminate in the 4WD LOW instrument cluster to indicate that TOW/HAUL mode has Four-Wheel Drive Low Range — This range provides low been activated. Pushing the switch a second time restores speed four-wheel drive. It maximizes torque (increased normal operation.
Page 177 STARTING AND OPERATING This electronically shifted transfer case is designed to be The selected position indicator light will flash until the NOTE: driven in the two–wheel drive position (2WD) for normal transfer case completes the shift. Do not attempt to make a shift while only the front or rear street and highway conditions on dry hard surfaced wheels are spinning.
Page 178: Five-Position Electronically Shifted Transfer Case - If Equipped
STARTING AND OPERATING OSITION LECTRONICALLY WARNING! Two-Wheel Drive High Range — This range is for normal — HIFTED RANSFER  You or others could be injured or killed if you leave street and highway driving on dry hard surfaced roads. QUIPPED the vehicle unattended with the transfer case in the 4WD AUTO...
Page 179 STARTING AND OPERATING When additional traction is required, the transfer case If the transfer case does not shift into the desired position, NOTE: 4WD HIGH and 4WD LOW positions can be used to one or more of the following events may occur: Do not attempt to make a shift while only the front or rear maximize torque to the front driveshaft, forcing the front wheels are spinning.
Page 180: Active-Level Four Corner Air Suspension
STARTING AND OPERATING ACTIVE-LEVEL FOUR CORNER AIR NOTE: cally lowered to OR1. Off-Road 2 may not be available due to vehicle payload, an instrument cluster message The vehicle will automatically enter Aero Mode when the SUSPENSION SYSTEM — IF EQUIPPED will be displayed when this occurs.
Page 181: Air Suspension Modes
STARTING AND OPERATING NOTE: level for speed changes (e.g. raising from Entry/ CAUTION! Exit Height at speed, lowering from Off Road Automatic Aero Mode may be disabled through vehicle Height at speed, etc.). settings in the instrument cluster display or through your When in ENTRY/EXIT setting, be aware of your Uconnect Radio if equipped.
Page 182: Instrument Cluster Display Messages
STARTING AND OPERATING Automatic Aero Mode may be disabled through vehicle Wheel Alignment Mode PERATION settings in the instrument cluster display or through your Before performing a wheel alignment, this mode must be Uconnect Radio if equipped. Refer to “Instrument Cluster enabled.
Page 183: Active-Level Four Corner Air Suspension
STARTING AND OPERATING Pushing the height selector up once will move the  Entry/Exit Mode – Indicator lamp 5 will be illuminated suspension one position higher from the current position, when the vehicle is in Entry Exit Mode. Entry/Exit mode assuming all conditions are met (i.e.
Page 184 STARTING AND OPERATING cally lowered to NRH. Off-Road may not be available  Entry/Exit Mode (Lowers the vehicle approximately This system uses a lifting and lowering pattern which keeps due to vehicle payload, an instrument cluster display 3 inches (73 mm)) – This position lowers the vehicle the headlights from incorrectly shining into oncoming message will be shown when this occurs.
Page 185: Air Suspension Modes
STARTING AND OPERATING load leveling system. Refer to “Instrument Cluster Display” An audible chime will be heard whenever a system error WARNING! in “Getting To Know Your Instrument Panel” or “Uconnect has been detected. Settings” in “Multimedia” if equipped with a touch screen The air suspension system uses a high pressure volume of See an authorized dealer for system service if normal radio for further information.
Page 186: Axle Locker System - If Equipped
STARTING AND OPERATING Pushing the height selector switch up once will move the  Entry/Exit Mode – Indicator lamp 4 will be illuminated suspension one position higher from the current position, when the vehicle is in Entry Exit Mode. Entry/Exit mode assuming all conditions are met (i.e.
Page 187: Limited-Slip Differential - If Equipped
STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL — During the command to lock the rear axle, the indicator Care should be taken to avoid sudden accelerations when light will flash until the axle is locked. After the lock both rear wheels are on a slippery surface. This could IF EQUIPPED command has been successfully executed, the light will cause both rear wheels to spin, and allow the vehicle to...
Page 188: Stop/Start System - If Equipped
STARTING AND OPERATING If the Steering icon is displayed and the “SERVICE POWER Vehicles equipped with eTorque contain a heavy duty OSSIBLE EASONS NGINE STEERING – ASSIST OFF” message is displayed the motor generator and an additional hybrid electric battery UTOSTOP instrument cluster screen, they indicate the vehicle needs to store energy from vehicle deceleration for use on...
Page 189: To Start The Engine While In Autostop Mode
STARTING AND OPERATING  The engine hood has been opened. The STOP/START OFF message will appear in the TART NGINE HILE instrument cluster display. Refer to “Instrument  A STOP/START system error present. UTOSTOP Cluster Display” in “Getting To Know Your Instrument The engine may then be restarted by moving the Panel”...
Page 190: Speed Control - If Equipped
STARTING AND OPERATING SPEED CONTROL — IF EQUIPPED When the vehicle has reached the desired speed, push WARNING! the SET (+) or SET (-) button and release. Release the accelerator and the vehicle will operate at the selected When engaged, the Speed Control takes over accelerator Speed Control can be dangerous where the system speed.
Page 191: To Accelerate For Passing
STARTING AND OPERATING To Decrease Speed Control function performs differently. Please refer to the ESUME PEED proper section within this chapter. When the Speed Control is set, you can decrease speed by To resume a previously set speed, push the RES button pushing the SET (-) button.
Page 192: Adaptive Cruise Control (Acc) Operation
STARTING AND OPERATING WARNING! WARNING!  Adaptive Cruise Control (ACC) is a convenience You should switch off the ACC system: system. It is not a substitute for active driver involve-  When driving in fog, heavy rain, heavy snow, sleet, ment.
Page 193: Activating Adaptive Cruise Control (Acc)
STARTING AND OPERATING CTIVATING DAPTIVE RUISE ONTROL WARNING! (ACC) Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally You can only engage ACC if the vehicle speed is above set the system or cause it to go faster than you want. 0 mph (0 km/h).
Page 194: To Cancel
STARTING AND OPERATING The speed increment shown is dependent on the chosen ANCEL ESUME speed unit of U.S. (mph) or Metric (km/h): The following conditions cancel the system: If there is a set speed in memory push the RES (resume) U.S.
Page 195: Setting The Following Distance In Acc
STARTING AND OPERATING Metric Speed (km/h) ETTING OLLOWING ISTANCE  Pushing the SET (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h. The specified following distance for Adaptive Cruise Control (ACC) can be set by varying the distance setting ...
Page 196: Overtake Aid
STARTING AND OPERATING  The distance setting is changed. NOTE: The “BRAKE!” Screen in the instrument cluster display is a  The system disengages. Refer to the information on warning for the driver to take action and does not neces- ACC Activation.
Page 197: Adaptive Cruise Control (Acc) Menu
STARTING AND OPERATING While ACC is holding your vehicle at a standstill, if the Adaptive Cruise Control Set The “ACC/FCW Unavailable Wipe Front Radar Sensor” driver seat belt is unbuckled or the driver door is opened, message can sometimes be displayed while driving in When the SET (+) or the SET (-) button (located on the the parking brake will be activated, and the ACC system highly reflective areas (i.e.
Page 198: Precautions While Driving With Acc
STARTING AND OPERATING NOTE: If weather conditions are not a factor, the driver should RECAUTIONS HILE RIVING examine the windshield and the camera located on the  If the “ACC/FCW Unavailable Wipe Front Radar Sensor” back side of the inside rear view mirror. They may require message occurs frequently (e.g.
Page 199 STARTING AND OPERATING Towing A Trailer Turns And Bends Using ACC On Hills ACC while towing a trailer is recommended only with an When driving on a curve with ACC engaged, the system When driving on hills, ACC may not detect a vehicle in your Integrated Trailer Brake Controller.
Page 200: General Information
STARTING AND OPERATING Lane Changing ENERAL NFORMATION ACC may not detect a vehicle until it is completely in the The following regulatory statement applies to all Radio lane in which you are traveling. In the illustration shown, Frequency (RF) devices equipped in this vehicle: ACC has not yet detected the vehicle changing lanes and This device complies with Part 15 of the FCC Rules and it may not detect the vehicle until it's too late for the ACC...
Page 201: Normal (Fixed Speed) Cruise Control Mode
STARTING AND OPERATING vehicle will operate at the selected speed. Once a speed To Decrease Speed ORMAL IXED PEED RUISE has been set a message “CRUISE CONTROL SET TO MPH When the Normal (Fixed Speed) Cruise Control is set, you ONTROL (km/h)”...
Page 202: Parksense Front And Rear Park Assist
STARTING AND OPERATING  The Electronic Stability Control/Traction Control released when the vehicle is in REVERSE if the system changing the gear while the automatic brakes are System (ESC/TCS) activates. detects a possible collision with an obstacle. being applied.  The vehicle parking brake is applied. NOTE: The automatic braking function is intended to assist the driver in avoiding possible collisions with detected...
Page 203: Parksense Sensors
STARTING AND OPERATING If an obstacle is detected in the left, right, or center ENSE ENSORS regions, the display will show a single arc in the left and/ The six ParkSense sensors, located in the front fascia/ or right regions and the system will produce a tone. As the bumper, monitor the area in front of the vehicle that is vehicle moves closer to the obstacle, the display will show within the sensors’...
Page 204 STARTING AND OPERATING The vehicle is close to the obstacle when the display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Fast Tone Continuous Tone WARNING ALERTS FOR REAR Rear Distance Greater than...
Page 205: Enabling And Disabling Front And/Or Rear Parksense
STARTING AND OPERATING Front Park Assist Audible Alerts NOTE: outer surface and the underside of the rear fascia/ bumper and/or front fascia/bumper is clean and clear of Arc alerts from the enabled ParkSense system, will ParkSense will turn off the Front Park Assist audible alert snow, ice, mud, dirt or other obstruction and then cycle the interrupt the five second messages, and the instrument (chime) after approximately three seconds when an...
Page 206: Parksense Active Park Assist System - If Equipped
STARTING AND OPERATING  When you move the gear selector to the REVERSE posi- WARNING! CAUTION! tion and Front or Rear ParkSense is turned off, the instrument cluster display will show a vehicle graphic  Drivers must be careful when backing up even when ...
Page 207: Enabling And Disabling The Parksense Active Park Assist System
STARTING AND OPERATING  During a semi-automatic maneuver, if the driver NOTE: The ParkSense Active Park Assist system will allow a touches the steering wheel after being instructed to maximum of eight shifts between DRIVE and REVERSE. If If your vehicle is equipped with a 12–inch Uconnect remove their hands from the steering wheel, the the maneuver cannot be completed within eight shifts, the display, the ParkSense Active Park Assist switch is located...
Page 208: Parallel Parking Space Assistance Operation/Display
STARTING AND OPERATING Once the vehicle is in position, you will be instructed to ARALLEL ARKING PACE SSISTANCE stop the vehicle’s movement and remove your hands from PERATION ISPLAY the steering wheel. When the ParkSense Active Park Assist system is enabled the “Active ParkSense Searching - Push OK To Switch To Perpendicular Park”...
Page 209 STARTING AND OPERATING When the driver places the gear selector into the REVERSE NOTE: position, the system may instruct the driver to wait for  It is the driver’s responsibility to use the brake and steering to complete. accelerator during the semi-automatic parking maneuver.
Page 210 STARTING AND OPERATING When the driver places the gear selector into the DRIVE When the vehicle has reached the end of its forward position, the system may instruct the driver to wait for movement, the system will instruct the driver to check steering to complete.
Page 211: Perpendicular Parking Space Assistance Operation/Display
STARTING AND OPERATING The system will then instruct the driver to check their Once the driver pushes OK for a perpendicular parking  When seeking for a parking space, the driver should surroundings and move backward. maneuver, the “Active ParkSense Searching - Push OK for drive as parallel or perpendicular (depending on the Parallel Park”...
Page 212 STARTING AND OPERATING Once the vehicle is in position, you will be instructed to When the driver places the gear selector into the REVERSE NOTE: stop the vehicle’s movement and remove your hands from position, the system may instruct the driver to wait for ...
Page 213 STARTING AND OPERATING When the vehicle has reached the end of its backward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Check Surroundings — Shift To Drive Check Surroundings — Move Forward When the driver places the gear selector into the DRIVE When the vehicle has reached the end of its forward position, the system may instruct the driver to wait for...
Page 214 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will The system will then instruct the driver to check their WARNING! be instructed to place the gear selector into the REVERSE surroundings and move backward. position. Drivers must be careful when performing parallel or perpendicular parking maneuvers even when using the ParkSense Active Park Assist system.
Page 215: Lanesense - If Equipped
STARTING AND OPERATING LANESENSE — IF EQUIPPED to the driver when the driver’s hands are not detected on NOTE: the steering wheel. The system will cancel if the driver The LaneSense system will retain the last system state on does not return their hands to the wheel. or off from the last ignition cycle when the ignition is ENSE PERATION...
Page 216: Changing Lanesense Status
STARTING AND OPERATING  When the LaneSense system senses the lane has been  When the LaneSense system senses the lane has been approached and is in a lane departure situation, the approached and is in a lane departure situation, the visual warning in the instrument cluster display will left lane line flashes yellow (on/off).
Page 217: Parkview Rear Back Up Camera
STARTING AND OPERATING NOTE: transmission is shifted into PARK, the ignition is placed in A dashed center line overlay indicates the center of the the OFF position, or the touchscreen X button to disable vehicle to assist with parking or aligning to a hitch/ ...
Page 218: Surround View Camera System
STARTING AND OPERATING If the vehicle is in PARK, Zoom View is available until the When the vehicle is shifted into REVERSE, the rear camera CAUTION! gear selector is placed in DRIVE or REVERSE and speeds view and top view is the default view of the system are at or above 8 mph (13 km/h).
Page 219 STARTING AND OPERATING Modes Of Operation NOTE: If the Backup Camera view was selected through the Standard Backup Camera view can be manually activated  Due to wide angle cameras in mirrors, the image will Surround View Screen, exiting out of the Rear View by selecting “Back Up Camera”...
Page 220: Refueling The Vehicle - Gasoline Engines
STARTING AND OPERATING REFUELING THE VEHICLE — GASOLINE Deactivation NOTE: The system is deactivated in the following conditions if it  If snow, ice, mud, or any foreign substance builds up on ENGINES was activated automatically: the camera lenses, clean the lenses, rinse with water, and dry with a soft cloth.
Page 221: Refueling The Vehicle - Diesel Engine
STARTING AND OPERATING Put the vehicle in park and switch the ignition off. When the fuel nozzle “clicks” or shuts off, the fuel Ensure funnel is inserted fully to hold flapper doors tank is full. open. Push the center-rear edge of the fuel filler door (3 o'clock position) and release to open.
Page 222 STARTING AND OPERATING Fill the vehicle with fuel – when the fuel nozzle NOTE: “clicks” or shuts off, the fuel tank is full. Ensure funnel is inserted fully to hold flapper door open. Remove the fuel nozzle and close the fuel door. Pour fuel into funnel opening.
Page 223: Avoid Using Contaminated Fuel
STARTING AND OPERATING NOTE: VOID SING ONTAMINATED IESEL XHAUST LUID When working with DEF, it is important to know that: Fuel that is contaminated by water or dirt can cause Your vehicle is equipped with a Selective Catalytic  Any containers or parts that come into contact with DEF severe damage to the engine fuel system.
Page 224 STARTING AND OPERATING Diesel Exhaust Fluid (DEF) Fill Procedure fault related to the DEF system, the gauge may not CAUTION! update to the new level. See an authorized dealer NOTE: for service.  Never add anything other than DEF to the tank – Refer to “Fluids And Lubricants”...
Page 225: Vehicle Loading
STARTING AND OPERATING VEHICLE LOADING The entire vehicle should first be weighed on a commercial scale to ensure that the Gross Vehicle Weight Rating The tire size on the Vehicle Certification Label represents (GVWR) has not been exceeded. The weight on the front ROSS EHICLE EIGHT...
Page 226: Common Towing Definitions
STARTING AND OPERATING Gross Combination Weight Rating (GCWR) To maintain the New Vehicle Limited Warranty coverage, adjustable friction associated with the telescoping motion follow the requirements and recommendations in this to dampen any unwanted trailer swaying motions while The Gross Combination Weight Rating (GCWR) is the total manual concerning vehicles used for trailer towing.
Page 227 STARTING AND OPERATING RECOMMENDED DISTRIBUTION HITCH WARNING! ADJUSTMENT  An improperly adjusted weight distributing hitch Towing With 1500 Air Suspension system may reduce handling, stability and braking performance and could result in a collision. Set air suspension to normal ride height. No action is required if already in normal ride height.
Page 228: Trailer Hitch Type And Maximum Trailer Weight
STARTING AND OPERATING Attach the trailer to the vehicle without the weight Use the instrument cluster or touch screen radio Example 1500 Height distribution bars connected. settings and switch off tire jack mode. Make sure the Measurement Example (mm) truck returns to normal ride height. Perform a visual Measure the height from the top of the front wheel inspection of the trailer and weight distributing hitch H2-H1...
Page 229: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING Class III Bumper Hitch Access RAILER ONGUE EIGHT OWING EQUIREMENTS Remove the cap with a trim stick or screwdriver to access To promote proper break-in of your new vehicle drivetrain the Class III hitch attachment. components, the following guidelines are recommended. NOTE: Be careful not to scratch the bumper step pad.
Page 230 STARTING AND OPERATING Towing Requirements — Tires hydraulic surge actuated brake system, an electronic WARNING! brake controller is not required.  Do not attempt to tow a trailer while using a compact  When hauling cargo or towing a trailer, do not over- ...
Page 231 STARTING AND OPERATING Integrated Trailer Brake Module — The user interface consists of the following: GAIN If Equipped Manual Brake Control Lever The GAIN setting is used to set the trailer brake control for the specific towing condition and should be changed as Slide the manual brake control lever to the left to activate Your vehicle may have an Integrated Trailer Brake Module towing conditions change.
Page 232 STARTING AND OPERATING Push the UP or DOWN buttons until the Trailer Brake In a traffic-free environment, tow the trailer on a dry, Repeat steps 8 and 9 until the GAIN setting is at a point Type appears on the screen. level surface at a speed of 20–25 mph (30–40 km/h) just below trailer wheel lockup.
Page 233: Towing Tips
STARTING AND OPERATING Automatic Transmission NOTE:  Disconnect trailer wiring connector from the vehicle The DRIVE range can be selected when towing. The before launching a boat (or any other device plugged transmission controls include a drive strategy to avoid into vehicle’s electrical connect) into water.
Page 234: Snowplow
STARTING AND OPERATING Cooling System NOTE: WARNING! The vehicle must remain in the engine running position To reduce potential for engine and transmission while attaching a trailer for proper leveling of the air Attaching a snowplow to this vehicle could adversely overheating, take the following actions: suspension system.
Page 235: Recreational Towing - Two-Wheel Drive Models
STARTING AND OPERATING NOTE: Properly secure the rear wheels to the dolly, following CAUTION! the dolly manufacturer's instructions.  When towing your vehicle, always follow applicable  Tow only in the forward direction. Towing this vehicle Turn the ignition OFF. state and provincial laws.
Page 236 STARTING AND OPERATING Shifting Into NEUTRAL (N) Using a ballpoint pen or similar object, push and hold pushing the NEUTRAL (N) button or are no longer met the recessed transfer case NEUTRAL (N) button (at during the shift, the NEUTRAL (N) indicator light will Use the following procedure to prepare your vehicle for the center of the transfer case switches).
Page 237: Driving Tips
STARTING AND OPERATING DRIVING TIPS Flowing/Rising Water Turn the engine OFF. The transmission will automat- ically select PARK when the engine is turned off. WARNING! Release the brake pedal. RIVING LIPPERY URFACES Disconnect vehicle from the tow vehicle. Do not drive on or across a road or path where water is Acceleration flowing and/or rising (as in storm run-off).
Page 238: Off-Road Driving Tips
STARTING AND OPERATING  Check threaded fasteners for looseness, particularly RIVING CAUTION! on the chassis, drivetrain components, steering, and Care should be taken when attempting to climb steep hills suspension. Retighten them, if required, and torque to  Always check the depth of the standing water before or driving diagonally across a hill or slope.
Page 239: In Case Of Emergency
IN CASE OF EMERGENCY HAZARD WARNING FLASHERS This is an emergency warning system and it should not be If equipped, the overhead console contains an ASSIST and used when the vehicle is in motion. Use it only when your a SOS button. vehicle is disabled or signaling a safety hazard warning for other motorists.
Page 240 IN CASE OF EMERGENCY ASSIST Call  The vehicle brand WARNING! The ASSIST Button is used to automatically connect you to  The last known GPS coordinates of the vehicle  If anyone in the vehicle could be in danger (e.g., fire any one of the following support centers: You should be able to speak with the SOS operator or smoke is visible, dangerous road conditions or...
Page 241: General Information
IN CASE OF EMERGENCY SOS Call System Limitations Even if the SOS Call system is fully functional, factors NOTE: beyond FCA US LLC’s control may prevent or stop the SOS Vehicles sold in Mexico DO NOT have SOS Call system ...
Page 242: Bulb Replacement
IN CASE OF EMERGENCY Le présent appareil est conforme aux CNR d`Innovation, La operación de este equipo está sujeta a las siguientes NOTE: Science and Economic Development applicables aux dos condiciones: Changes or modifications not expressly approved by the appareils radio exempts de licence. L'exploitation est party responsible for compliance could void the user’s es posible que este equipo o dispositivo no cause autorisée aux deux conditions suivantes:...
Page 243 IN CASE OF EMERGENCY Exterior Bulbs Bulb Name Bulb Number Turn Signal / Front Position (Halogen Reflector Headlamp) 7444NA Turn Signal / Front Position (LED Headlamps) LED (Serviced at an Authorized Dealer) Front Side Marker (Halogen Reflector Headlamp) Front Side Marker (LED Headlamps) LED (Serviced at an Authorized Dealer) Front Fog Lamps (Halogen Reflector Headlamp) H11LL...
Page 244: Replacing Exterior Bulbs
IN CASE OF EMERGENCY Disengage the bulb access cover by rotating counter- EPLACING XTERIOR ULBS clockwise. Base Quad: Low Beam Headlamp, High Disconnect the internal lamp wiring harness Beam Headlamp, Front Park And Turn — If connector from the low beam bulb. Equipped CAUTION! Low Beam...
Page 245 IN CASE OF EMERGENCY Fog Lamps — If Equipped Rotate the bulb counterclockwise a quarter turn to Side Marker Lamp unlock the bulb from the lamp. Open the hood. Reach under and behind the front bumper to access Pull the bulb straight out from the housing. the back of the front fog lamp housing.
Page 246 IN CASE OF EMERGENCY Rear Tail/Stop, Turn Signal And Backup Pull the bulb straight out of the socket. Lamps CAUTION! Remove the two screws and push pins retainers that Do not contaminate the bulb glass by touching it with pass through the bed sheet metal. your fingers or by allowing it to contact other oily surfaces.
Page 247: Fuses
IN CASE OF EMERGENCY FUSES Separate the connector holding the housing and XTERNAL OWER ISTRIBUTION wiring harness to the body. ENTER WARNING! The Power Distribution Center is located in the engine  When replacing a blown fuse, always use an appro- compartment near the battery.
Page 248 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 25 Amp Clear Fuel Pump Motor – 5 Amp Tan MGU – If Equipped – – Spare – – Spare – – Spare – – Spare 20 Amp Blue –...
Page 249 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 40 Amp Green – Exterior Lights 2 50 Amp Red – ESP Module 30 Amp Pink – Front Wiper – 10 Amp Red PCM / ECM 40 Amp Green – ESP Module –...
Page 250 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Rear Defroster – – Spare 30 Amp Pink – Htr Ctrl – If Equipped (Diesel Only) – – Spare – – Spare – – Spare – 10 Amp Red Supply / Purging Pump –...
Page 251: Internal Power Distribution Center
IN CASE OF EMERGENCY After removing the screws, gently pull both the left CAUTION! and right side of the fuse panel cover to release the fastener clips.  When installing the power distribution center cover, it is important to ensure the cover is properly posi- tioned and fully latched.
Page 252 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Trailer Tow Receptacle – 20 Amp Yellow Module Seat Heater Front (Pass) – – Spare – 20 Amp Yellow Module PPU Cooling Fan 40 Amp Green –...
Page 253 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 40 Amp Green – Mod Integrated Trailer Brake – 15 Amp Blue Mod Cluster CCN / Mod Cyber Security – 5 Amp Tan Mod Cluster CCN / Mod SGW – 10 Amp Red Mod ORC –...
Page 254 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – – Spare Rear View Mirror / Humidity Rain And Light Sensor (HRLS) / SW F48A – 10 Amp Red Window Passenger / Rear USB / Wireless Charging Pad Mod Mod CVPM / SNSR Blind Spot / HDLP Adaptive Front Lighting Sensor –...
Page 255: Jacking And Tire Changing
IN CASE OF EMERGENCY CAUTION! WARNING!  When installing the power distribution center cover,  The jack is designed to be used as a tool for changing it is important to ensure the cover is properly posi- tires only. The jack should not be used to lift the tioned and fully latched.
Page 256 IN CASE OF EMERGENCY Release the tool bag straps from the jack and remove Assembled For Jack Operation 1 — Lug Wrench tools from bag. 2 — Long Extension Without Spring Clip 2 3 — Long Extension With Spring Clip 3 4 —...
Page 257: Removing The Spare Tire
IN CASE OF EMERGENCY EMOVING PARE Remove the spare tire before attempting to jack up the truck. Attach the lug wrench to the extension tubes with the curved angle facing away from the vehicle. Remove the protective cover over the access hole for the winch mechanism by sliding the cover upward.
Page 258: Preparations For Jacking
IN CASE OF EMERGENCY Lift the spare tire with one hand to give clearance to NOTE: tilt the retainer at the end of the cable. The winch mechanism is designed for use with the extension tubes only. Use of an air wrench or other power tools is not recommended and can damage the winch.
Page 259 IN CASE OF EMERGENCY NOTE: CAUTION! WARNING! Keep the jack and tools aligned with raising the vehicle. Do not attempt to raise the vehicle by jacking on  Never start or run the engine with the vehicle on a locations other than those indicated in the Jacking jack.
Page 260 IN CASE OF EMERGENCY By rotating the lug wrench clockwise, raise the vehicle until the wheel just clears the ground surface. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 261: To Stow The Flat Or Spare
IN CASE OF EMERGENCY If your vehicle is equipped with a wheel center cap, Attach the lug wrench to the extension tubes with the install the cap and remove the wheel blocks. Do not curved angle facing away from the vehicle. Insert the install chrome or aluminum wheel center caps on the extension tubes through the access hole between the spare wheel.
Page 262: Reinstalling The Jack And Tools
IN CASE OF EMERGENCY JUMP STARTING Place the jack and tools in the storage position EINSTALLING OOLS holding the jack by the jack turn-screw, slip the jack Tighten the jack all the way down by turning the jack and tools under the seat so that the bottom slot If your vehicle has a discharged battery, it can be jump turn-screw counterclockwise until the jack is snug.
Page 263: Preparations For Jump Start
IN CASE OF EMERGENCY Apply the parking brake, shift the automatic REPARATIONS TART transmission into PARK and turn the ignition OFF. The battery in your vehicle is located in the front of the Turn off the heater, radio, and all unnecessary engine compartment, behind the left headlight assembly.
Page 264: If Your Engine Overheats
IN CASE OF EMERGENCY IF YOUR ENGINE OVERHEATS Connecting The Jumper Cables Once the engine is started, remove the jumper cables in the reverse sequence: Connect the positive (+) end of the jumper cable to In any of the following situations, you can reduce the the positive (+) post of the discharged vehicle.
Page 265: Manual Park Release
IN CASE OF EMERGENCY Follow these steps to activate the Manual Park Release: CAUTION! Apply firm pressure to the brake pedal while seated Driving with a hot cooling system could damage your in the driver’s seat. vehicle. If the temperature gauge reads HOT (H), pull Apply the parking brake if possible.
Page 266: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE Verify the transmission is in PARK. WARNING! Confirm that the tether has retracted fully and This section describes procedures for towing a disabled Fast spinning tires can be dangerous. Forces generated re-install the access cover. If the access cover cannot vehicle using a commercial towing service.
Page 267: Two-Wheel Drive Models
IN CASE OF EMERGENCY Towing Condition Wheels OFF The Ground 2WD Models 4WD Models See instructions in “Recreational Towing” under “Starting And Operating” If transmission is operable:  Automatic Transmission in PARK Flat Tow NONE  Transmission in NEUTRAL  Transfer Case in NEUTRAL (N) ...
Page 268: Four-Wheel Drive Models
IN CASE OF EMERGENCY ENHANCED ACCIDENT RESPONSE SYSTEM — HEEL RIVE ODELS MERGENCY OOKS QUIPPED (EARS) The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the Your vehicle may be equipped with emergency tow hooks. vehicle on a flatbed or with one end of vehicle raised and This vehicle is equipped with an Enhanced Accident NOTE:...
Page 269: Servicing And Maintenance
SERVICING AND MAINTENANCE SCHEDULED SERVICING — GASOLINE An authorized dealer will reset the oil change indicator Once A Month Or Before A Long Trip: message after completing the scheduled oil change. If a  Check engine oil level. ENGINES scheduled oil change is performed by someone other than ...
Page 270 SERVICING AND MAINTENANCE At Every Oil Change Interval As Indicated By Oil Change Indicator System:  Inspect the engine cooling system protection and hoses.  Inspect the exhaust system.  Inspect the engine air cleaner if using in dusty or off-road conditions. ...
Page 271 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace cabin air filter. Replace engine air filter. If equipped with Stop/Start, replace accessory drive belt with OEM grade Mopar belt. Replace spark plugs. Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 272: Scheduled Servicing - Diesel Engine
SERVICING AND MAINTENANCE SCHEDULED SERVICING — DIESEL ENGINE Conditions will cause the change oil message to illuminate Display” in “Getting To Know Your Instrument Panel” for more frequently. Have your vehicle serviced as soon as further information. possible, within the next 500 miles (805 km). Your vehicle is equipped with an automatic oil change NOTE: indicator system.
Page 273 SERVICING AND MAINTENANCE NOTE: Using white lithium grease, lubricate the door hinge roller pivot joints twice a year to prevent premature wear. At Every Second Oil Change Interval As Indicated By Oil Change Indicator System:  Change fuel filter. Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections...
Page 274: Additional Maintenance - B6 To B20 Biodiesel
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Replace engine air filter. Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Replace accessory drive belt(s). Inspect the transfer case fluid, change for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 275: Engine Compartment
SERVICING AND MAINTENANCE ENGINE COMPARTMENT 3.6L E NGINE TART 1 — Motor Generator Unit Coolant Reservoir Pressure Cap 6 — Battery 2 — Engine Coolant Reservoir Pressure Cap 7 — Power Distribution Center (Fuses) 3 — Engine Oil Dipstick 8 — Washer Fluid Reservoir 4 —...
Page 276: L Engine Without Stop/Start
SERVICING AND MAINTENANCE 5.7L E NGINE ITHOUT TART 1 — Air Cleaner Filter 6 — Battery 2 — Engine Coolant Pressure Cap 7 — Power Distribution Center (Fuses) 3 — Engine Oil Fill 8 — Washer Fluid Reservoir 4 — Engine Oil Dipstick 9 —...
Page 277: L Engine With Stop/Start
SERVICING AND MAINTENANCE 5.7L E NGINE TART 1 — Air Cleaner Filter 6 — Battery 2 — Engine Coolant Pressure Cap 7 — Power Distribution Center (Fuses) 3 — Engine Oil Fill 8 — Washer Fluid Reservoir 4 — Engine Oil Dipstick 9 —...
Page 278: L Diesel Engine
SERVICING AND MAINTENANCE 3.0L D IESEL NGINE 1 — Air Cleaner Filter 5 — Brake Fluid Cap 2 — Engine Coolant Reservoir Cap 6 — Battery 3 — Engine Oil Dipstick 7 — Power Distribution Center (PDC) 4 — Engine Oil Fill 8 —...
Page 279: Checking Oil Level
SERVICING AND MAINTENANCE NOTE: HECKING EVEL AINTENANCE ATTERY It is possible for your oil level to be slightly higher than a To ensure proper engine lubrication, the engine oil must Your vehicle is equipped with a maintenance-free battery. previous check. This would be due to diesel fuel that may be maintained at the correct level.
Page 280: Pressure Washing
SERVICING AND MAINTENANCE NOTE: CAUTION! WARNING! Hemi engine (5.7L) at times can tick right after startup and  If a “fast charger” is used while the battery is in the then quiet down after approximately 30 seconds. This is You can be badly injured working on or around a motor vehicle, disconnect both vehicle battery cables normal and will not harm the engine.
Page 281: Engine Oil Filter
SERVICING AND MAINTENANCE Engine Oil Viscosity — 3.6L Engine Engine Oil Viscosity (SAE Grade) — Disposing Of Used Engine Oil And Oil Diesel Engine Filters Mopar SAE 0W-20 engine oil approved to FCA Material Standard MS-6395 is recommended for all operating Care should be taken in disposing of used engine oil and CAUTION! temperatures.
Page 282 SERVICING AND MAINTENANCE Remove the air cleaner filter element from the WARNING! housing assembly. The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance.
Page 283: Draining Fuel/Water Separator Filter - Diesel Engine
SERVICING AND MAINTENANCE RAINING ATER EPARATOR NDERBODY OUNTED ILTER CAUTION! — D — D ILTER IESEL NGINE EPLACEMENT IESEL NGINE If the “Water In Fuel Indicator Light” remains on, DO NOT START the engine before you drain water from the The fuel/water separator filter housing is located inside NOTE: fuel filter to avoid engine damage.
Page 284: Priming If The Engine Has Run Out Of Fuel - Diesel Engine
SERVICING AND MAINTENANCE Turn engine off. Start the engine using the “Normal Starting”  In addition, commercially available fuel additives are procedure. Refer to “Starting The Engine” in “Starting not necessary for the proper operation of your diesel Place a drain pan under the fuel filter assembly. and Operating”...
Page 285: Diesel Exhaust Fluid
SERVICING AND MAINTENANCE The cabin air filter is located in the fresh air inlet behind IESEL XHAUST LUID CAUTION! the glove compartment. Perform the following procedure Diesel Exhaust Fluid (DEF) sometimes known simply by to replace the filter: Do not use chemical flushes in your air conditioning the name of its active component, UREA—is a key system as the chemicals can damage your air Open the glove compartment and remove all...
Page 286 SERVICING AND MAINTENANCE There are glove compartment travel stops on both Remove the cabin air filter by pulling it straight out of sides of the glove compartment door, push inward on the housing. both sides of the glove compartment to release the glove compartment travel stops.
Page 287: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE Pull the tension tether outward and reinstall the glove CCESSORY RIVE NSPECTION compartment past the travel stops by pushing in on the glove compartment sides. WARNING!  Do not attempt to inspect an accessory drive belt with vehicle running. ...
Page 288: Body Lubrication
SERVICING AND MAINTENANCE Wiper Blade Removal/Installation NOTE: INDSHIELD IPER LADES Identify and correct problem before new belt is installed. Clean the rubber edges of the wiper blades and the CAUTION! NOTE: windshield periodically with a sponge or soft cloth and a If your vehicle is equipped with Stop/Start belt must be Do not allow the wiper arm to spring back against the mild nonabrasive cleaner.
Page 289: Exhaust System
SERVICING AND MAINTENANCE To disengage the wiper blade from the wiper arm, Slide the wiper blade up into the hook on the wiper CAUTION! press the release tab on the wiper blade and while arm, latch engagement will be accompanied by an holding the wiper arm with one hand, slide the wiper audible click.
Page 290: Cooling System
SERVICING AND MAINTENANCE Engine Coolant Checks Selection Of Coolant To minimize the possibility of catalytic converter damage:  Do not interrupt the ignition when the transmission is Check the engine coolant (antifreeze) protection every Refer to “Fluids And Lubricants” in “Technical in gear and the vehicle is in motion.
Page 291 SERVICING AND MAINTENANCE Adding Coolant to the temperatures occurring in the area where the WARNING! vehicle is operated. Your vehicle has been built with an improved engine  Do not use a pressure cap other than the one speci-  Some vehicles require special tools to add coolant coolant (OAT coolant conforming to MS.90032) that properly.
Page 292 SERVICING AND MAINTENANCE Checking Coolant Level — 5.7L Engines If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be With the engine OFF and cold, the level of the engine safely driven. The vapor will soon dissipate. coolant should be between the ADD and SAFE range on ...
Page 293: Charge Air Cooler - Inter-Cooler (Diesel Engine)
SERVICING AND MAINTENANCE — I Fluid Level Check — Brake Master Cylinder HARGE OOLER NTER OOLER WARNING! The fluid level of the master cylinder should be checked IESEL NGINE  To avoid contamination from foreign matter or mois- when performing under the hood service or immediately if ture, use only new brake fluid or fluid that has been The charge air cooler is positioned in front of the radiator the brake system warning lamp indicates system failure.
Page 294: Rear Axle And 4X4 Front Driving Axle Fluid Level
SERVICING AND MAINTENANCE If you notice fluid leakage or transmission malfunction, The fluid level should be even with the bottom of the fill CAUTION! visit an authorized dealer immediately to have the hole (within 1/4 in (6.4 mm) of edge of hole) for the front transmission fluid level checked.
Page 295: Transfer Case
SERVICING AND MAINTENANCE TIRES NOTE: RANSFER  P (Passenger) — Metric tire sizing is based on US design Selection Of Lubricant AFETY NFORMATION standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Use only the manufacturer's recommended fluid. Refer to Tire safety information will cover aspects of the following Example: P215/65R15 95H.
Page 296 SERVICING AND MAINTENANCE TIRE SIZING CHART EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
Page 297 SERVICING AND MAINTENANCE EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:  XL = Extra load (or reinforced) tire, or  LL = Light load tire or ...
Page 298 SERVICING AND MAINTENANCE EXAMPLE: 01 = Number representing the year in which the tire was manufactured (two digits)  01 means the year 2001  Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991 Tire Terminology And Definitions Term...
Page 299 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure This placard tells you important information about the: Number of people that can be carried in the vehicle. NOTE: The proper cold tire inflation pressure is listed on the Total weight your vehicle can carry. driver’s side B-Pillar or the rear edge of the driver's side Tire size designed for your vehicle.
Page 300 SERVICING AND MAINTENANCE (4) The resulting figure equals the To determine the maximum loading conditions of your Metric Example For Load Limit vehicle, locate the statement “The combined weight of available amount of cargo and luggage For example, if “XXX” amount equals 635 kg and there will occupants and cargo should never exceed XXX kg or XXX be five 68 kg passengers in your vehicle, the amount of load capacity.
Page 301 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 302: Tires - General Information
SERVICING AND MAINTENANCE — G At least once a month: IRES ENERAL NFORMATION WARNING!  Check and adjust tire pressure with a good quality Tire Pressure  Always drive with each tire inflated to the recom- pocket-type pressure gauge. Do not make a visual judg- mended cold tire inflation pressure.
Page 303 SERVICING AND MAINTENANCE Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Tire Repair NOTE: during operation. DO NOT reduce this normal pressure TPMS Sensor must be replaced after driving the vehicle on If your tire becomes damaged, it may be repaired if it build up or your tire pressure will be too low.
Page 304 SERVICING AND MAINTENANCE Tread Wear Indicators Life Of Tire Replacement Tires Tread wear indicators are in the original equipment tires to The service life of a tire is dependent upon varying factors The tires on your new vehicle provide a balance of many help you in determining when your tires should be including, but not limited to: characteristics.
Page 305: Tire Types
SERVICING AND MAINTENANCE Snow Tires YPES WARNING! Some areas of the country require the use of snow tires All Season Tires — If Equipped  Do not use a tire, wheel size, load rating, or speed during the Winter. Snow tires can be identified by a rating other than that specified for your vehicle.
Page 306 SERVICING AND MAINTENANCE Since this tire has limited tread life, the original equipment Inflate collapsible tire only after the wheel is properly CAUTION! tire should be repaired (or replaced) and reinstalled on installed to the vehicle. Inflate the collapsible tire using your vehicle at the first opportunity.
Page 307: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE Limited Use Spare — If Equipped Your wheels are susceptible to deterioration caused by NOTE: salt, sodium chloride, magnesium chloride, calcium If you intend parking or storing your vehicle for an The limited use spare tire is for temporary emergency use chloride, etc., and other road chemicals used to melt ice extended period after cleaning the wheels with wheel only.
Page 308: Tire Rotation Recommendations
SERVICING AND MAINTENANCE Please follow the table below for proper tire size, chain type, and axle recommendations: Vehicle Axle Recommendations Tire Sizes Chain Class 275/65R18 1500 Models Rear Only S Class 275/55R20 Refer to the “Maintenance Plan” for the proper WARNING! CAUTION! maintenance intervals.
Page 309: Department Of Transportation Uniform
SERVICING AND MAINTENANCE DEPARTMENT OF TRANSPORTATION significantly from the norm due to under controlled conditions on a variations in driving habits, service specified indoor laboratory test wheel. UNIFORM TIRE QUALITY GRADES practices, and differences in road Sustained high temperature can cause The following tire grading categories characteristics and climate.
Page 310: Storing The Vehicle
SERVICING AND MAINTENANCE STORING THE VEHICLE What Causes Corrosion? RESERVING ODYWORK Corrosion is the result of deterioration or removal of paint Washing If you are storing your vehicle for more than 21 days, we and protective coatings from your vehicle. recommend that you take the following steps to minimize ...
Page 311 SERVICING AND MAINTENANCE Your bumpers are susceptible to deterioration caused by  If you detect any stone chips or scratches in the paint, To Help Maintain The Appearance Of Your Spray-On salt, sodium chloride, magnesium chloride, calcium touch them up immediately. The cost of such repairs is Bedliner, Follow The Steps Below: chloride, etc., and other road chemicals used to melt ice considered the responsibility of the owner.
Page 312: Interiors
SERVICING AND MAINTENANCE INTERIORS Seat Belt Maintenance LASTIC OATED ARTS Do not bleach, dye or clean the belts with chemical Use Mopar Total Clean to clean vinyl upholstery. EATS ABRIC ARTS solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric.
Page 313: Leather Parts
SERVICING AND MAINTENANCE NOTE: EATHER ARTS LASS URFACES If equipped with light colored leather, it tends to show any Mopar Total Clean is specifically recommended for leather All glass surfaces should be cleaned on a regular basis foreign material, dirt, and fabric dye transfer more so than upholstery.
Page 314: Technical Specifications
TECHNICAL SPECIFICATIONS IDENTIFICATION DATA If either the front or rear hydraulic system loses normal NOTE: braking capability, the remaining system will still function Do not oil wheel studs. For chrome wheels, do not with some loss of overall braking effectiveness. This will substitute with chrome plated wheel nuts.
Page 315: Fuel Requirements - Gasoline Engines
TECHNICAL SPECIFICATIONS The use of higher octane “Premium” gasoline is not Poor quality gasoline can cause problems such as hard required, as it will not provide any benefit over “Regular” starting, stalling, and hesitations. If you experience these gasoline in these engines. symptoms, try another brand of gasoline before considering service for the vehicle.
Page 316: Gasoline/Oxygenate Blends
TECHNICAL SPECIFICATIONS Indiscriminate use of fuel system cleaning agents should If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, YSTEM AUTIONS be avoided. Many of these materials intended for gum and the engine will have some or all of these symptoms: varnish removal may contain active solvents or similar ...
Page 317: Carbon Monoxide Warnings
TECHNICAL SPECIFICATIONS will provide good performance. If the vehicle is exposed to ARBON ONOXIDE ARNINGS IESEL PECIFICATIONS extreme cold (below 20°F or -7°C), or is required to operate at colder-than-normal conditions for prolonged This diesel engine has been developed to take advantage WARNING! periods, use climatized No.
Page 318 TECHNICAL SPECIFICATIONS Fuel Oxidation Stability — Must Use Fuel For regular use of biodiesel blends between 6% and 20% CAUTION! (B6–B20) it is important that you understand and comply Within Six Months Of Manufacture with these requirements. Refer to the “Maintenance Plan” In the event that the vehicle is filled with biodiesel and Biodiesel fuel has poor oxidation stability which can result in “Scheduled Servicing”...
Page 319: Fluid Capacities - Gasoline Engines
TECHNICAL SPECIFICATIONS Biodiesel Fuel Filter Change Intervals NOTE: with 6% - 20% biodiesel blends. Failure to comply with these oil change and fuel filter requirements for vehicles Under no circumstances should oil change intervals The use of biodiesel requires more frequent fuel filter operating on biodiesel blends up to B20 may result in exceed 8,000 miles (12,875 km) or 6 months, if regular change intervals.
Page 320: Fluid Capacities - Diesel Engine
TECHNICAL SPECIFICATIONS FLUID CAPACITIES — DIESEL ENGINE Metric Fuel (Approximate) 3.0L Diesel Engine 26 Gallons 98.5 Liters Diesel Exhaust Fluid Tank Tradesman/Rebel Models 5.14 Gallons 19.5 Liters All Other Models 5.74 Gallons 21.7 Liters Engine Oil With Filter 3.0L Diesel Engine 8.5 Quarts 8.0 Liters Cooling System...
Page 321: Chassis
TECHNICAL SPECIFICATIONS Component Fluid, Lubricant, or Genuine Part We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Engine Oil – 5.7L Engine FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade.
Page 322: Fluids And Lubricants - Diesel Engine
TECHNICAL SPECIFICATIONS Component Fluid, Lubricant, or Genuine Part Front Axle We recommend you use Mopar GL-5 Synthetic Axle Lubricant SAE 75W-85. We recommend you use Mopar Synthetic Gear Lubricant SAE 75W-90 (MS-A0160). Rear Axle (3.21/3.55) Limited-Slip Rear Axles require the addition of 5 oz. (148 ml) Mopar Limited Slip Additive (MS-10111).
Page 323 TECHNICAL SPECIFICATIONS Component Fluid, Lubricant, or Genuine Part Use good quality diesel fuel from a reputable supplier in your vehicle. Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.
Page 324: Chassis
TECHNICAL SPECIFICATIONS HASSIS Component Fluid, Lubricant, or Genuine Part Only use Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid or equivalent. Failure to Automatic Transmission use the correct fluid may affect the function or performance of your transmission. Transfer Case We recommend you use Mopar BW44–44 Transfer Case Fluid.
Page 325: Multimedia
MULTIMEDIA UCONNECT SYSTEMS The risk of unauthorized and unlawful access to your NOTE: vehicle systems may still exist, even if the most recent  FCA US LLC or your dealer may contact you directly version of vehicle software (such as Uconnect software) is For detailed information about your Uconnect 4/4C/4C regarding software updates.
Page 326: Uconnect 3 Settings
MULTIMEDIA Push the SETTINGS button, then press the Settings button When making a selection, press the button on the CONNECT ETTINGS on the touchscreen to display the Settings menu screen. touchscreen to enter the desired menu. Once in the In this mode, the Uconnect system allows you to access desired menu, press and release the preferred setting programmable features that may be equipped such as until the button is highlighted.
Page 327 MULTIMEDIA Display After pressing the Display button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Display Mode Auto Manual Touchscreen Beep Fuel Saver Display NOTE: The “Fuel Saver Display”...
Page 328 MULTIMEDIA Voice After pressing the Voice button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock After pressing the Clock button on the touchscreen, the following setting will be available:...
Page 329 MULTIMEDIA Setting Name Selectable Options Lane Sense Warning Early Late Lane Sense Strength High ParkSense Sound Only Sounds & Display NOTE: The ParkSense system scans for objects behind the vehicle when the transmission gear selector is in REVERSE and the vehicle speed is less than 7 mph (11 km/h). It provides an alert (audible and/or visual) to indicate the proximity to other objects.
Page 330 MULTIMEDIA Setting Name Selectable Options Hill Start Assist NOTE: When the “Hill Start Assist” feature is selected, the Hill Start Assist (HSA) system becomes active. Brakes — If Equipped After pressing the Brakes button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 331 MULTIMEDIA Setting Name Selectable Options NOTE: When the “Headlight Illumination On Approach” feature is selected, it allows the adjustment of the amount of time the headlights remain on when the doors are unlocked with the key fob. Headlights With Wipers Auto Dim High Beams Flash Lights With Lock NOTE:...
Page 332 MULTIMEDIA Setting Name Selectable Options Sound Horn With Lock 1st Press 2nd Press Remote Door Unlock Driver NOTE: The “Remote Door Unlock” feature allows you to program your remote door locks to unlock “All doors” or only the “Driver door” with the first push of the key fob or when grabbing the Passive Entry door handle.
Page 333 MULTIMEDIA Power Side Steps — If Equipped After pressing the Power Side Steps button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Power Side Steps Automatic Stow Auto Comfort Systems —...
Page 334 MULTIMEDIA Engine Off Options After pressing the Engine Off Options button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Easy Exit Seats 0 sec 30 sec Headlight Off Delay 60 sec 90 sec...
Page 335 MULTIMEDIA Setting Name Selectable Options NOTE: When this feature is selected, the air suspension system is disabled to prevent auto leveling of the suspension while the vehicle is on a jack changing a tire. Transport Mode NOTE: When the “Transport Mode” feature is selected, the air suspension system is disabled to assist with flatbed towing. Wheel Alignment Mode NOTE: The “Wheel Alignment Mode”...
Page 336 MULTIMEDIA Audio After pressing the Audio button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Balance/Fade Front Back Left Right NOTE: The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the speaker icon or use the arrows to adjust, tap the C icon to readjust to the center. Equalizer –...
Page 337 MULTIMEDIA Phone/Bluetooth® After pressing the Phone/Bluetooth® button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Paired Phones List of Paired Phones NOTE: The “Paired Phones” feature shows which phones are paired to the Phone/Bluetooth® system. For further information, refer to the Uconnect Owner’s Manual Supplement. SiriusXM®...
Page 338 MULTIMEDIA Restore Settings After pressing the Restore Settings button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Restore Settings Cancel NOTE: When the “Restore Settings” feature is selected, it will reset the Display, Clock, Audio, and Radio Settings to their default settings. If “Yes” is selected, a pop-up will appear asking "Are you sure you want to reset your settings to default?”...
Page 339: Uconnect 4/4C/4C Nav Settings
MULTIMEDIA 4/4C/4C NAV S Press the Apps button on the touchscreen then press the When making a selection, press the button on the CONNECT ETTINGS Settings button on the touchscreen to display the Settings touchscreen to enter the desired menu. Once in the menu screen.
Page 340 MULTIMEDIA Display After pressing the Display button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Display Mode Auto Manual NOTE: When Day or Night is selected for the Display Mode, the usage of the Parade Mode feature will cause the radio to activate the Display Brightness Day control even though the head- lights are on.
Page 341 MULTIMEDIA Units After pressing the Units button on the touchscreen, you may select each unit of measurement independently displayed in the instrument cluster display and Navigation system (if equipped). The selectable units of measurement are listed below: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Units...
Page 342 MULTIMEDIA Clock After pressing the Clock button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Sync Time With GPS Set Time Hours – Set Time Minutes –...
Page 343 MULTIMEDIA Setting Name Selectable Options Active Parkview Backup Camera Guidelines NOTE: The “Active ParkView Backup Camera Guidelines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its projected backup path, based on the steering wheel position when the option is checked.
Page 344 MULTIMEDIA Setting Name Selectable Options Forward Collision Warning Sensitivity Near NOTE: Sets the distance in which a Forward Collision Warning occurs. Lane Sense Warning Early Late NOTE: Sets what distance the steering wheel provides feedback for potential lane departures. Lane Sense Strength High ParkSense Sound Only...
Page 345 MULTIMEDIA Mirrors & Wipers After pressing the Mirrors & Wipers button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Tilt Side Mirrors In Reverse NOTE: When the “Tilt Side Mirrors In Reverse”...
Page 346 MULTIMEDIA Lights After pressing the Lights button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Headlight Off Delay – NOTE: When the “Headlight Off Delay” feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. Headlight Illumination On Approach –...
Page 347 MULTIMEDIA Doors & Locks After pressing the Doors & Locks button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Auto Door Locks NOTE: When the “Auto Door Locks” feature is selected, all doors lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit”...
Page 348 MULTIMEDIA Setting Name Selectable Options Passive Entry NOTE: The “Passive Entry” feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. Personal Settings Linked To Key Fob NOTE:  The “Personal Settings Linked To Key Fob” feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. ...
Page 349 MULTIMEDIA Engine Off Options After pressing the Engine Off Options button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Engine Off Power Delay – NOTE: When the “Engine Off Power Delay”...
Page 350 MULTIMEDIA Setting Name Selectable Options Flash Lights With Lower NOTE: When the “Flash Lights With Lower” feature is selected, the front and rear turn signals will flash when the key fob remote lower button is pressed twice. This feature may be selected with or without the Sound Horn on Lower feature selected.
Page 351 MULTIMEDIA Trailer After pressing the Trailer button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Trailer Select Trailer 1 Trailer 2 Trailer 3 Trailer 4 Trailer Brake Type Light Electric Heavy Electric...
Page 352 MULTIMEDIA Setting Name Selectable Options Speed Adjusted Volume NOTE: The “Speed Adjusted Volume” feature increases or decreases volume relative to vehicle speed. Surround Sound NOTE: The “Surround Sound” feature provides a simulated surround sound mode. AUX Volume Offset NOTE: The “AUX Volume Offset” feature provides the ability to tune the audio level for portable devices connected through the AUX input. Auto Play Phone/Bluetooth®...
Page 353 MULTIMEDIA Setting Name Selectable Options Smartphone Projection Manager Phone Pop-ups Displayed in Cluster SiriusXM® Setup — If Equipped After pressing the SiriusXM® Setup button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Tune Start...
Page 354 MULTIMEDIA System Information — If Equipped After pressing the System Information button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Software License System Software Information Screen NOTE: When the “Software License”...
Page 355 MULTIMEDIA Restore Settings To Default After pressing the Restore Settings To Default button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Restore Settings Cancel NOTE: When the “Restore Settings”...
Page 356: Uconnect 4C Nav With 12-Inch Display Settings
MULTIMEDIA 4C NAV W Press the Settings button on the touchscreen to display When making a selection, press the button on the CONNECT INCH the Settings menu screen. In this mode the Uconnect touchscreen to enter the desired menu. Once in the ISPLAY ETTINGS system allows you to access programmable features that...
Page 357 MULTIMEDIA Language After pressing the Language button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Language English (US) Español Français NOTE: When the “Language” feature is selected, you may select one of multiple languages (English (US) / Français / Español) for all display nomenclature, including the trip functions and the navigation system (if equipped).
Page 358 MULTIMEDIA Setting Name Selectable Options Set Theme Pre-configured Themes Touchscreen Beep Controls Screen Time-Out Fuel Saver Display NOTE: When selected, the system displays fuel saver mode in the instrument cluster. Navigation Turn-By-Turn Displayed in Cluster Phone Pop-Ups Displays In Cluster Ready To Drive Pop-Ups Units —...
Page 359 MULTIMEDIA Setting Name Selectable Options Pressure Temperature °F °C Voice Settings After pressing the Voice Settings button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Voice Response Length Brief Detailed...
Page 360 MULTIMEDIA Camera After pressing the Camera button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Surround View Camera Delay Surround View Camera Guidelines Parkview Backup Camera Delay NOTE: The “ParkView Backup Camera Delay”...
Page 361 MULTIMEDIA Safety & Driving Assistance After pressing the Safety & Driving Assistance button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Forward Collision Warning Warning Only Warning &...
Page 362 MULTIMEDIA Setting Name Selectable Options Trailer Length For Blind Spot Alert Auto Max (39.5 feet) NOTE: Auto detects the length of the trailer. Max sets all trailers to 39.5 ft (12 m). Power Side Step Auto Store Hill Start Assist Tire Fill Assist Mirrors &...
Page 363 MULTIMEDIA Brakes After pressing the Brake button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Brake Service NOTE: Selecting the “Brake Service” feature will display a pop-up asking whether or you would like to retract the park brakes to allow brake system service. Auto Park Brake Lights After pressing the Lights button on the touchscreen, the following settings will be available:...
Page 364 MULTIMEDIA Setting Name Selectable Options Auto Dim High Beams NOTE: When the “Auto Dim High Beams” feature is selected, the high beam headlights deactivate automatically under certain conditions. Daytime Running Lights NOTE: When the “Daytime Running Lights” feature is selected, the daytime running lights can be turned On or Off. This feature is only allowed by law in the country of the vehicle purchase. Steering Directed Lights NOTE: When the “Steering Directed Lights”...
Page 365 MULTIMEDIA Setting Name Selectable Options NOTE: When the “Flash Lights With Lock” feature is selected, the front and rear turn signals flash when the doors are locked or unlocked with the key fob. This feature may be selected with or without the “Sound Horn With Lock” feature selected. Sound Horn With Lock —...
Page 366 MULTIMEDIA Auto-On Comfort & Remote Start Systems — If Equipped After pressing the Auto-On Comfort & Remote Start Systems button on the touchscreen, the following setting will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Auto-On Driver Heated/Vented Seat &...
Page 367 MULTIMEDIA Suspension — If Equipped After pressing the Suspension button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Sound Horn With Lower NOTE: When the “Sound Horn With Lower” feature is selected, a short horn sound will occur when the key fob remote lower button is pushed. Flash Lights With Lower NOTE: When the “Flash Lights With Lower”...
Page 368 MULTIMEDIA Setting Name Selectable Options Four Corner Air Suspension Modes Tire Jack Mode Transport Mode Wheel Alignment Mode NOTE: There are three air suspension modes designed to protect the system in unique situations. Tire Jack Mode is selected to assist in changing a spare tire. Transport Mode is selected to assist when the vehicle is being flatbed towed.
Page 369 MULTIMEDIA Audio After pressing the Audio button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Balance/Fade Front Right Back Left NOTE: The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the speaker icon or use the arrows to adjust, tap the C icon to readjust to the center. Equalizer –...
Page 370 MULTIMEDIA Bluetooth® After pressing the Bluetooth® button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Phone Pop-Ups Displayed in Cluster Do Not Disturb List of Settings NOTE: Press “Do Not Disturb”...
Page 371 MULTIMEDIA SiriusXM® Setup — If Equipped After pressing the SiriusXM® Setup button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Sirius All Access Choose a Subscription Package Add Listener Add up to five profiles NOTE:...
Page 372: Safety And General Information
MULTIMEDIA Reset After pressing the Reset button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Selectable Options Reset App Drawer To Default Order Cancel Restore Settings Cancel NOTE: When the “Restore Settings”...
Page 373: Uconnect 3 With 5-Inch Display
MULTIMEDIA Safe Usage Of The Uconnect System Care And Maintenance 1 — RADIO Push the RADIO button on the faceplate to enter Radio  Read all instructions in this manual carefully before Touchscreen Mode. The different tuner modes, FM/AM/SXM (if using your system to ensure proper usage.
Page 374: Radio Mode
MULTIMEDIA 9 — PHONE The radio is equipped with the following modes: During a Seek Up function, if the radio reaches the starting station after passing through the entire band two times, Push the PHONE button on the faceplate to access the ...
Page 375 MULTIMEDIA SiriusXM® Satellite Radio Mode — © 2022 SiriusXM® Radio Inc. SiriusXM® and all related The Audio Menu shows the following options for you marks and logos are trademarks of SiriusXM® Radio Inc. to customize your audio settings: If Equipped This functionality is only available for radios equipped with ...
Page 376: Media Mode
MULTIMEDIA Clock Settings Seek Up/Seek Down Functions 3 — Additional Functions 4 — Info Push the SETTINGS button on the faceplate, or push Seek Up /Seek Down the MORE button on the faceplate, and then the 5 — Pause/Play Press and release the Seek Up button on the touchscreen SETTINGS button on the touchscreen.
Page 377 MULTIMEDIA Shuffle AUX Mode Browse Press the Browse button on the touchscreen to select Press the Shuffle button on the touchscreen to play the AUX Mode is entered by inserting a AUX device using a Artist, Albums, Genres, Songs, Playlists or Folders from the selections on the USB/iPod®...
Page 378: Phone Mode
MULTIMEDIA The Uconnect Phone is a voice-activated, hands-free,  Transfer calls from the system to the mobile phone and HONE in-vehicle communications system with voice command vice versa. Operating Phone Mode capability. Refer to Voice Recognition (VR) within this  Deactivate the microphone audio for privacy. publication for further information.
Page 379 MULTIMEDIA Search for available devices on your When prompted on the mobile phone, accept the If your phonebook does not contain any names, enter new Bluetooth®-enabled mobile phone. connection request from Uconnect Phone. names for the most frequently used numbers. ...
Page 380 MULTIMEDIA Select the Paired Phones or Paired Audio list using Select the specific device (mobile phone or  Only the phonebook of the currently connected mobile the corresponding button on the display. Bluetooth® device). phone is accessible. Select the specific device (mobile phone or Press the Make Favorite button.
Page 381 MULTIMEDIA Transferring/Call Continuation Recent Calls  Put on hold/resume The list of the last calls made for each of the following call  Deactivate/activate the microphone Transferring types can be displayed:  Transfer the call The ongoing calls can be transferred from the mobile ...
Page 382: Steering Wheel Audio Controls - If Equipped
MULTIMEDIA STEERING WHEEL AUDIO CONTROLS — READING MESSAGES The following describes the left-hand control operation in each mode. The system can read the messages received by the mobile IF EQUIPPED phone. ADIO PERATION To use this function, the mobile phone must support the The remote sound system controls are located on the back The button located in the center of the left-hand control SMS exchange function via Bluetooth®.
Page 383 MULTIMEDIA NOTE: Applicable to Uconnect 4C/4C NAV With 8.4-inch Display and Uconnect 4C NAV With 12-inch Display radios, Two devices can be plugged in at the same time, and both different scenarios are listed for when a non-phone device ports will provide charging capabilities. Only one port can transfer data to the system at a time.
Page 384: Radio Operation And Mobile Phones
MULTIMEDIA not satisfactorily “clear” by the repositioning of the Canada license-exempt RSS standard(s). Operation is antenna, it is recommended that the radio volume be subject to the following two conditions: turned down or off during mobile phone operation when This device may not cause harmful interference, and not using Uconnect (if equipped).
Page 385: Uconnect Voice Recognition Quick Tips
MULTIMEDIA ence in a residential installation. This equipment TARTED generates, uses and can radiate radio frequency energy and, if not installed and used in accordance All you need to control your Uconnect system with your with the instructions, may cause harmful interference voice are the buttons on your steering wheel.
Page 386: Radio
MULTIMEDIA TIP: ADIO Press the Browse button on the touchscreen to see all of Use your voice to quickly get to the AM, FM or SiriusXM® the music on your USB device. Your Voice Command must Satellite Radio stations you would like to hear. match exactly how the artist, album, song and genre infor- (Subscription or included SiriusXM®...
Page 387: Voice Text Reply
MULTIMEDIA TIP: OICE EPLY AVIGATION Your mobile phone must have the full implementation of Uconnect announces incoming text messages. Push the The Uconnect navigation feature helps you save time and the Message Access Profile (MAP) to take advantage of VR button or Phone button (if enabled) and say this feature.
Page 388: Using Do Not Disturb
MULTIMEDIA Android Auto™ allows you to use your voice to interact with Apple CarPlay® allows you to use your voice to interact SING ISTURB Android’s™ best-in-class speech technology through your with Siri through your vehicle’s voice recognition system, With Do Not Disturb, you can disable notifications from vehicle’s voice recognition system, and use your and use your smartphone to project your iPhone®...
Page 389: General Information
MULTIMEDIA La operación de este equipo está sujeta a las siguientes Uconnect System Support: ENERAL NFORMATION dos condiciones:  US residents visit www.DriveUconnect.com or call: The following regulatory statement applies to all Radio es posible que este equipo o dispositivo no cause 1-877-855-8400 (24 hours a day 7 days a week) Frequency (RF) devices equipped in this vehicle: interferencia perjudicial y...
Page 390: Customer Assistance
CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE IF YOU NEED ASSISTANCE FCA US LLC C USTOMER ENTER FOR YOUR VEHICLE P.O. Box 21–8004 The manufacturer and its authorized dealers are vitally interested in your satisfaction. We want you to be happy Auburn Hills, MI 48321–8004 with our products and services.
Page 391: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
CUSTOMER ASSISTANCE MOPAR® PARTS FCA US LLC is not responsible for any service contract you USTOMER SSISTANCE may have purchased from another manufacturer. If you EARING PEECH MPAIRED require service after the FCA US LLC New Vehicle Limited Mopar original equipment parts & accessories and factory (TDD/TTY) Warranty expires, please refer to the contract documents, filled fluids are available from an authorized dealer.
Page 392: In Canada
CUSTOMER ASSISTANCE PUBLICATION ORDER FORMS To contact NHTSA, you may call the Owner's Manuals Vehicle Safety Hotline toll free at These Owner's Manuals have been prepared with the To order the following manuals, you may use either the assistance of service and engineering specialists to 1-888-327-4236 (TTY: website or the phone numbers listed below.
Page 393 INDEX Air Conditioning, Operating Tips ........53 Automatic Transmission Limp Home Mode ....172 Air Filter .................279 Auxiliary Driving Systems ..........118 Adaptive Cruise Control (ACC) (Cruise Control)..189 Air Pressure Axle Fluid............ 292 Adding Engine Coolant (Antifreeze) ......289 Tires................300 Axle Lubrication ............
Page 394 Compact Spare Tire ............304 Disable Vehicle Towing ..........264 Contract, Service ............389 Disposal Camera ................. 215 Cooling Pressure Cap (Radiator Cap)......289 Antifreeze (Engine Coolant)........289 Camera, Rear ............215 Cooling System .............288 Do Not Disturb .............. 386 Capacities, Fuel........... 317 Adding Coolant (Antifreeze) ........289 Door Ajar ...............
Page 395 Engine ................273 Engine Fuel ..............281 Air Cleaner............... 279 Engine Oil..........279 Garage Door Opener (HomeLink)........61 Block Heater ..........162 Engine Oil Disposal..........279 Gasoline, Clean Air ............313 Break-In Recommendations ........166 Flashers Gasoline, Reformulated ..........313 Compartment......273 Turn Signals ..........
Page 396 Hitches Courtesy/Reading ............. 43 Trailer Towing............226 Cruise............... 109 Key Fob Hoisting................. 293 Daytime Running............39 Panic Alarm..............14 HomeLink (Garage Door Opener) ........61 Electronic Stability Program (ESP) Indicator ..102 Programming Additional Key Fobs ....16 Hood Prop................59 Exterior.............. 39 Key Fob Battery Service (Remote Keyless Entry) ..
Page 397 Locks Automatic Door ............25 New Vehicle Break-In Period........166 Paint Care ..............308 Child Protection ............25 Panic Alarm..............14 Power Door..............22 Parking Brake ............... 167 Low Tire Pressure System ........... 125 ParkSense Active Park Assist ........204 Occupant Restraints.............129 Lubrication, Body ............286 ParkSense System, Rear ..........
Page 398 Reporting Safety Defects ..........389 Seat Belt Reminder..........129 Restraints, Child ............144 Untwisting Procedure..........132 Radial Ply Tires............. 301 Restraints, Head ............. 32 Seat Belts Maintenance ..........310 Radiator Cap (Coolant Pressure Cap)....288 Rotation, Tires...............306 Seats ..............27 Radio Operation ............382 Adjustment ............
Page 399 Spare Tires ..........303 Sway Control, Trailer.............118 Safety..............293 Spark Plugs ..............318 Synthetic Engine Oil............279 Sizes................. 294 Speed Control Snow Tires ............... 303 Accel/Decel............. 189 Spare Tires ........... 303 Cancel..............189 Spinning..............301 Tailgate................79 Resume ..............189 Trailer Towing ............228 Tailgate Removal ............
Page 400 Transmission ..............170 Wind Buffeting..........55 Automatic ............170 Window Fogging ............. 53 Vehicle Identification Number (VIN) ......312 Fluid ..............319 Windows................54 Vehicle Loading........... 223 Maintenance ............291 Power ................. 54 Vehicle Modifications/Alterations ......... 11 Shifting ..............169 Rear Sliding ............... 55 Vehicle Storage............53 Transporting Pets ............
Page 403 The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in an accident and personal injury. FCA US LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road.
Page 404 Whether it is providing information about specific product features, taking a tour through your vehicle’s heritage, knowing what steps to take following an accident or scheduling your next appointment, we know you will find the app an important extension of your Ram vehicle. Simply download the app, select your make and model and enjoy the ride.

Dodge RAM 1500 2020 Owner's Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dodge RAM 1500 2020

Summary of Contents for Dodge RAM 1500 2020