KROHNE OPTIFLEX 8200 C Handbook page 81

OPTIFLEX 8200 C/F/S
Menu Function
No.
Output Function
I1
Scale 4mA I1
Scale 20mA I1
Optional Output
mode
Output Function
I2
Scale 4mA I2
Scale 20mA I2
06/2018 - 4006448901 - MA OPTIFLEX 8200 R01 en
Function description
The output function for output 1. Make
a selection from a list of output
functions to scale the current values in
relation to a given point (usually the
device process connection or the tank
bottom). The output current value is
shown on a bar graph in normal mode
if the measurement name (displayed
measurement) is the same as the
output function. Conversion
parameters (DISTANCE CONV., LEVEL
CONVERSION etc.) are shown if there
is volume or mass data in menu item
1.2.0 Conversion Setup 1.2.0 Conversion Setup 1.2.0 Conversion Setup 1.2.0 Conversion Setup.
This function gives a measurement
value to 4 mA (output 1).
This function gives a measurement
value to 20 mA (output 1).
This function operates the optional
second output (output 2).
If you set this function to "CURRENT",
the second output supplies 4...20 mA.
Give the settings for this current output
in Output Function I2 Output Function I2, Scale 4mA I2 Scale 4mA I2 and
Output Function I2 Output Function I2 Scale 4mA I2 Scale 4mA I2
Scale 20mA I2 Scale 20mA I2 Scale 20mA I2 Scale 20mA I2.
If you set this function to "RELAY", the
second output supplies a switch signal.
Give the settings for this relay signal in
Switch Function, Set Point/Threshold Switch Function Set Point/Threshold,
Switch Function Switch Function Set Point/Threshold Set Point/Threshold
Alarm Mode and Hysteresis Alarm Mode Alarm Mode Alarm Mode Hysteresis Hysteresis Hysteresis. If Switch
Function Function Function Function is set to "ERROR LIST", set a
condition in Error List Error List only.
Error List Error List
The output function for output 2. Make
a selection from a list of output
functions to scale the current values in
relation to a given point (usually the
device process connection or the tank
bottom). The output current value is
shown on a bar graph in normal mode
if the measurement name (displayed
measurement) is the same as the
output function. Conversion
parameters (DISTANCE CONV., LEVEL
CONVERSION etc.) are shown if there
is volume or mass data in menu item
1.2.0 Conversion Setup. 1.2.0 Conversion Setup 1.2.0 Conversion Setup 1.2.0 Conversion Setup
This function is available if Optional
Output Mode Output Mode Output Mode is set to "CURRENT". Output Mode
This function gives a measurement
value to 4 mA (output 2).
This function is available if Optional
Output Mode is set to "CURRENT". Output Mode
Output Mode Output Mode
This function gives a measurement
value to 20 mA (output 2).
This function is available if Optional
Output Mode Output Mode is set to "CURRENT".
Output Mode Output Mode
www.krohne.com
Selection list or range of
values
LEVEL, LEVEL CONVERSION,
DISTANCE, DISTANCE CONV.,
INTERFACE LEVEL,
INTERFACE CONVERSION,
INTERFACE DISTANCE,
INTERFACE DIST. CONV.,
LAYER, LAYER CONVERSION,
DIELECTRIC PRODUCT,
DIELECTRIC GAS,
CONVERTER TEMPERATURE,
SENSOR TEMPERATURE
min-max:
min-max:
DISABLE, CURRENT, RELAY
Switch Switch Switch
LEVEL, LEVEL CONVERSION,
DISTANCE, DISTANCE CONV.,
INTERFACE LEVEL,
INTERFACE CONVERSION,
INTERFACE DISTANCE,
INTERFACE DIST. CONV.,
LAYER, LAYER CONVERSION,
DIELECTRIC PRODUCT,
DIELECTRIC GAS,
CONVERTER TEMPERATURE,
SENSOR TEMPERATURE
Optional Optional Optional
min-max:
Optional
Optional Optional
min-max:
Optional Optional Optional
OPERATION
Default
LEVEL
1
3
2
3
2
3
4
DISTANCE
1
3
2
3
2
6
81