Sorter; Adjust - Canon imageRUNNER ADVANCE C3325 Series Service Manual

SORTER

ADJUST

SORTER>ADJUST
STP-F1 Adj front 1-stpl pstn: half size, Fin-U1
Lv.1 Details To adjust the front 1-staple position on A3/B4/A4/B5/LDR/LTR/
EXEC/8K/16K paper.
As the value is changed by 1, the staple position is moved by 0.49
mm.
+: Toward rear
-: Toward front
Use case When the A3/B4/A4/B5/LDR/LTR/EXEC/8K/16K paper front staple
position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -6 to 6
Unit 0.49 mm
Default value 0
STP-F2 Adj front 1-staple pstn: R size, Fin-U1
Lv.1 Details To adjust the front 1-staple position on A4R/LGL/LTRR paper.
As the value is changed by 1, the staple position is moved by 0.49
mm.
+: Toward rear
-: Toward front
Use case When the A4R/LGL/LTRR paper front staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -6 to 6
Unit 0.49 mm
Default value 0
STP-R1 Adj rear 1-stpl pstn: half size, Fin-U1
Lv.1 Details To adjust the rear 1-staple position on A3/B4/A4/B5/LDR/LTR/
EXEC/8K/16K paper.
As the value is changed by 1, the staple position is moved by 0.49
mm.
+: Toward rear
-: Toward front
Use case When the A3/B4/A4/B5/LDR/LTR/EXEC/8K/16K paper rear staple
position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -6 to 6
Unit 0.49 mm
Default value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER>ADJUST
STP-R2 Adj rear 1-staple pstn: R size, Fin-U1
Lv.1 Details To adjust the rear 1-staple position on A4R/LGL/LTRR paper.
As the value is changed by 1, the staple position is moved by 0.49
mm.
+: Toward rear
-: Toward front
Use case When the A4R/LGL/LTRR paper rear staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -6 to 6
Unit 0.49 mm
Default value 0
STP-2P Adj 2-stapling position: Fin-G1
Lv.1 Details To adjust the 2-staple position.
As the value is changed by 1, the staples position moves by 0.1 mm.
+: Toward rear
-: Toward front
Use case When the staples position in front/rear direction is displaced in the
2-stapling mode
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
SDL-STP Adj of Saddle Stitcher stpl pstn: Fin-U1
Lv.1 Details To adjust the staple position at the time of saddle stitching.
As the value is changed by 1, the staple position is moved by 0.5 mm.
+: Downward
-: Upward
Use case When misalignment occurs at the staple position for saddle stitching
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -3 to 3
Unit 0.5 mm
SDL-ALG Adj of Saddle align width: Fin-U1
Lv.1 Details To adjust the move distance of the Alignment Plate for saddle stitching.
When the value is increased by 1, the alignment position moves in the
push-in direction by 0.5 mm.
Use case When misalignment occurs during the saddle stitching
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
Unit 0.5 mm
8-227
8-227