Canon imageRUNNER ADVANCE C3325 Series Service Manual page 670

COPIER>FUNCTION>INSTALL
BRWS-ACT ON/OFF of service browser
Lv.1 Details To set ON/OFF of service browser.
ON/OFF of service browser switches whenever the main power switch
is turned OFF/ON after execution.
If connection with the UGW server is successful, "OK!" is displayed. If
"NG!" is displayed, execute a communication test using COM-TEST.
The setting is enabled after reboot. Whether the service browser is ON
or OFF can be checked in BRWS-STS (1: ON, 2: OFF).
Use case - When using the service browser
- At operation check
Adj/set/operate method 1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution After execution, turn OFF/ON the main power switch. After reboot, be
sure to check the usage status in BRWS-STS.
Display/adj/set range At normal termination: OK, At abnormal termination: NG
Related service mode COPIER> FUNCTION> INSTALL> COM-TEST
COPIER> DISPLAY> USER> BRWS-STS
CDS-CTL Setting of country/area when CDS is used
Lv.1 Details To set country/area to enable CDS.
Use case When enabling CDS
Adj/set/operate method 1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range CA (Canada), LA (Latin America), HK (Hong Kong) and the country/
area specified in COPIER> OPTION> FNC-SW> CONFIG.
Default value It differs according to the location.
Related service mode COPIER> OPTION> FNC-SW> CONFIG
Supplement/memo CDS: Contents Delivery System
HD-CRYP Exe HDD Encrypt Board ini install mod
Lv.1 Details To automatically execute operation necessary for initial installation of
the HDD Encryption Board.
By turning OFF the main power switch after execution, the HDD
Encryption Board can be installed.
Use case At installation of the HDD Encryption Board
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
RDSHDPOS Automatic adjustment of shading position
Lv.1 Details To adjust the shading position automatically.
Use case When replacing the Scanner Unit
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range At start of operation: START, During operation: ACTIVE, When
operation finished normally: OK!
Required time 10 sec
8
Service Mode > COPIER > FUNCTION > INSTALL
8 Service Mode > COPIER > FUNCTION > INSTALL
COPIER>FUNCTION>INSTALL
BIT-SVC OFF/ON of Web service function of E-RDS
Lv.1 Details To set whether to use Web service function of Embedded-RDS.
When 0 is set, authentication information cannot be obtained from
Embedded-RDS.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
EXTH-SET Transfer/fixing btch set for ext hvy ppr
Lv.1 Details Image failure may occur on extra heavy paper fed from the Multi-
purpose Tray using the Media Adjustment kit-A1.
To collectively set the paper allotted voltage, fixing control temperature
and ITOP control temperature at the time of secondary transfer for
extra heavy paper.
When 1 is set, the specified values* are applied to all the setting
values for extra heavy paper. Even after the application of the specified
values, they can be changed manually.
When 0 is set, all the corresponding setting values are returned to the
initial values.
* For details, refer to the Installation Procedure for Media Adjustment
kit-A1.
Use case When installing the Media Adjustment kit-A1
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
3) Execute auto gradation adjustment (full adjustment).
Caution - When changing the setting value from 0 to 1, all the corresponding
setting values are overwritten with the specified values. Therefore, be
sure to back up (write down) the setting values as needed.
- When changing the setting value from 1 to 0, values of all the
changed items are returned to the initial values.
Display/adj/set range 0 to 1
0: Set the initial values, 1: Set the specified values
Default value 0
Related service mode COPIER> ADJUST> HV-TR> TR-DUP1 - 12, TR-ENV1 - 12, TR-
PPR1- 12, TR-VL1 - 12
COPIER> OPTION> IMG-FIX> FXS-TM15, 16, 18, 19, TMP-TB18, 19,
21, 22
Supplement/memo Extra heavy paper: heavy paper (221 to 300 g/m2), 1-sided coated
paper (164 to 300 g/m2) and 2-sided coated paper (164 to 300 g/m2)
8-119
T-8-33
8-119