Canon imageRUNNER ADVANCE C3325 Series Service Manual page 510

Error■ Detail■
Location Item
code Code
E614 0311 00 Title Flash■PCB■error
Detection■ An■error■was■detected■in■the■system■area.■(File■could■not■be■
description written■in■the■Flash■PCB■after■startup■or■I/O■error■after■startup)
Remedy [Related■parts]
•■ Flash■PCB■(UN61)
•■ Main■Controller■PCB■(UN05)■(Unit■of■replacement:■MAIN■
CONTROLLER■PCB■ASS'Y)
[Remedy]■Perform■the■following■in■the■order■while■checking■
whether■the■error■is■cleared.
•■ Reinstall■the■necessary■application■software■and■restore■the■
backup■data■once■the■error■is■cleared.
1.■After■turning■OFF■the■main■power,■remove■and■then■install■the■
Flash■PCB■to■check■that■it■is■installed■properly.
2.■Turn■ON■the■main■power,■and■check■whether■the■error■is■
cleared.
3.■Obtain■the■necessary■backup■data■by■referring■to■the■backup■
data■list.
4.■Enter■safe■mode■using■(2+8)■startup,■and■execute■[4]■Clear/
Format>■[2]■Flash■Format■(Flash■format)■using■a■USB■memory.
5.■After■replacing■the■Flash■PCB,■reinstall■the■system■software■
using■SST■or■a■USB■memory.
6.■Replace■the■Main■Controller■PCB.
[Reference]■For■backup■and■restoration,■refer■to■"Adjustment>■
Actions■after■Replacement"■and■"Appendix>■Backup■Data■List"■in■
the■Service■Manual.
7
Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Description
7 Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Error■ Detail■
Location Item
code Code
E614 0401 00 Title Flash■PCB■error
Detection■ Logical■partition■error■was■detected.■(Initialization■failed■at■startup■
description or■I/O■error■at■startup)
When■this■error■occurs,■the■system■has■not■been■started■normally.■
Therefore,■it■may■not■be■recorded■in■the■error■log.
Remedy [Related■parts]
•■ Flash■PCB■(UN61)
•■ Main■Controller■PCB■(UN05)■(Unit■of■replacement:■MAIN■
CONTROLLER■PCB■ASS'Y)
[Remedy]■Perform■the■following■in■the■order■while■checking■
whether■the■error■is■cleared.
•■ Reinstall■the■necessary■application■software■and■restore■the■
backup■data■once■the■error■is■cleared.
1.■After■turning■OFF■the■main■power,■remove■and■then■install■the■
Flash■PCB■to■check■that■it■is■installed■properly.
2.■Turn■ON■the■main■power,■and■check■whether■the■error■is■
cleared.
3.■Obtain■the■necessary■backup■data■by■referring■to■the■backup■
data■list.
4.■Enter■safe■mode■using■(2+8)■startup,■and■execute■[4]■Clear/
Format>■[2]■Flash■Format■(Flash■format)■using■a■USB■memory.
5.■After■replacing■the■Flash■PCB,■reinstall■the■system■software■
using■SST■or■a■USB■memory.
6.■Replace■the■Main■Controller■PCB.
[Reference]■For■backup■and■restoration,■refer■to■"Adjustment>■
Actions■after■Replacement"■and■"Appendix>■Backup■Data■List"■in■
the■Service■Manual.
7-84
Description
7-84