Canon imageRUNNER ADVANCE C3325 Series Service Manual page 645

COPIER>ADJUST>HV-TR
TR-ENV9 Sec trns indiv setting environment:set 9
Lv.2 Details To set the environment (absolute moisture content) for setting 9.
Setting 9 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV9, TR-PPR9 and
TR-DUP9. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL9 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR9, TR-DUP9, TR-VL9, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV10 Sec trn indiv setting environment:set 10
Lv.2 Details To set the environment (absolute moisture content) for setting 10.
Setting 10 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV10, TR-PPR10 and
TR-DUP10. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL10 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR10, TR-DUP10, TR-VL10, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8
Service Mode > COPIER > ADJUST > HV-TR
8 Service Mode > COPIER > ADJUST > HV-TR
COPIER>ADJUST>HV-TR
TR-ENV11 Sec trn indiv setting environment:set 11
Lv.2 Details To set the environment (absolute moisture content) for setting 11.
Setting 11 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV11, TR-PPR11 and
TR-DUP11. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL11 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR11, TR-DUP11, TR-VL11, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV12
Sec trn indiv setting environment:set 12
Lv.2 Details To set the environment (absolute moisture content) for setting 12.
Setting 12 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV12, TR-PPR12 and
TR-DUP12. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL12 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR12, TR-DUP12, TR-VL12, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8-94
8-94