Canon imageRUNNER ADVANCE C3325 Series Service Manual page 641

COPIER>ADJUST>HV-TR
TR-PPR9 Sec trns indiv setting paper type: set 9
Lv.2 Details To set the paper type (paper weight) for setting 9.
Setting 9 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV9, TR-PPR9 and
TR-DUP9. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL9 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the paper type occurs (mottled
image/density loss due to excessive transfer/toner scattering on solid
image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 25
1: Plain paper 1 (64 to 75 g/m2), 2: Plain paper 2 (76 to 90 g/m2)/
Colored paper (64 to 82 g/m2), 3: Plain paper 3 (91 to 105 g/m2), 4:
Recycled paper 1 (64 to 75 g/m2), 5: Recycled paper 2 (76 to 90 g/m2),
6: Recycled paper 3 (91 to 105 g/m2), 7: Thin paper (52 to 63 g/m2), 8:
Heavy paper 1 (106 to 128 g/m2), 9: Heavy paper 2 (129 to 163 g/m2),
10: Heavy paper 3 (164 to 220 g/m2), 11: Heavy paper 4 (221 to 256 g/
m2), 12: 1-sided coated paper 1 (106 to 128 g/m2), 13: 1-sided coated
paper 2 (129 to 163 g/m2), 14: 1-sided coated paper 3 (164 to 220 g/
m2), 15: 2-sided coated paper 1 (106 to 128 g/m2), 16: 2-sided coated
paper 2 (129 to 163 g/m2), 17: 2-sided coated paper 3 (164 to 220 g/
m2), 18: Tracing paper (64 to 99 g/m2), 19: Transparency (121 to 220
g/m2), 20: Envelope (75 to 105 g/m2), 21: Postcard (164 to 220 g/m2),
22: Label (118 to 185 g/m2), 23: Pre-punched paper (64 to 75 g/m2),
24: Bond paper (83 to 99 g/m2), 25: Not used
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV9, TR-DUP9, TR-VL9, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8
Service Mode > COPIER > ADJUST > HV-TR
8 Service Mode > COPIER > ADJUST > HV-TR
COPIER>ADJUST>HV-TR
TR-PPR10 Sec trn indiv setting paper type: set 10
Lv.2 Details To set the paper type (paper weight) for setting 10.
Setting 10 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV10, TR-PPR10 and
TR-DUP10. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL10 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the paper type occurs (mottled
image/density loss due to excessive transfer/toner scattering on solid
image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 25
1: Plain paper 1 (64 to 75 g/m2), 2: Plain paper 2 (76 to 90 g/m2)/
Colored paper (64 to 82 g/m2), 3: Plain paper 3 (91 to 105 g/m2), 4:
Recycled paper 1 (64 to 75 g/m2), 5: Recycled paper 2 (76 to 90 g/m2),
6: Recycled paper 3 (91 to 105 g/m2), 7: Thin paper (52 to 63 g/m2), 8:
Heavy paper 1 (106 to 128 g/m2), 9: Heavy paper 2 (129 to 163 g/m2),
10: Heavy paper 3 (164 to 220 g/m2), 11: Heavy paper 4 (221 to 256 g/
m2), 12: 1-sided coated paper 1 (106 to 128 g/m2), 13: 1-sided coated
paper 2 (129 to 163 g/m2), 14: 1-sided coated paper 3 (164 to 220 g/
m2), 15: 2-sided coated paper 1 (106 to 128 g/m2), 16: 2-sided coated
paper 2 (129 to 163 g/m2), 17: 2-sided coated paper 3 (164 to 220 g/
m2), 18: Tracing paper (64 to 99 g/m2), 19: Transparency (121 to 220
g/m2), 20: Envelope (75 to 105 g/m2), 21: Postcard (164 to 220 g/m2),
22: Label (118 to 185 g/m2), 23: Pre-punched paper (64 to 75 g/m2),
24: Bond paper (83 to 99 g/m2), 25: Not used
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV10, TR-DUP10, TR-VL10, 2TR-
OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8-90
8-90