Canon imageRUNNER ADVANCE C3325 Series Service Manual page 516

Error■ Detail■
Location Item
code Code
E614 9003 00 Title Error■in■file■system■on■the■Flash■PCB
Detection■ Parameter■error■was■detected■at■startup.
description When■this■error■occurs,■the■system■has■not■been■started■normally.■
Therefore,■it■may■not■be■recorded■in■the■error■log.
Remedy [Remedy]■Perform■the■following■in■the■order■while■checking■
whether■the■error■is■cleared.
1.■Disconnect■and■then■connect■the■connectors■of■the■Flash■PCB■
(UN61)■and■the■Main■Power■Switch,■and■check■if■there■is■any■
bent■pin■or■cable■disconnection.
2.■Format■the■system.
2-1.■Enter■safe■mode■using■(2+8)■startup,■and■execute■[4]■
Clear/Format>■[2]■Flash■Format■(Flash■format)■using■a■
USB■memory.
2-2.■Reinstall■the■system■software■using■SST■or■a■USB■
memory.
3.■After■replacing■the■Flash■PCB,■reinstall■the■system■software■
using■SST■or■a■USB■memory.
E614 9004 00 Title Error■in■file■system■on■the■Flash■PCB
Detection■ Startup■error■was■detected.
description When■this■error■occurs,■the■system■has■not■been■started■normally.■
Therefore,■it■may■not■be■recorded■in■the■error■log.
Remedy [Remedy]■Perform■the■following■in■the■order■while■checking■
whether■the■error■is■cleared.
1.■Disconnect■and■then■connect■the■connectors■of■the■Flash■PCB■
(UN61)■and■the■Main■Power■Switch,■and■check■if■there■is■any■
bent■pin■or■cable■disconnection.
2.■Format■the■system.
2-1.■Enter■safe■mode■using■(2+8)■startup,■and■execute■[4]■
Clear/Format>■[2]■Flash■Format■(Flash■format)■using■a■
USB■memory.
2-2.■Reinstall■the■system■software■using■SST■or■a■USB■
memory.
3.■After■replacing■the■Flash■PCB,■reinstall■the■system■software■
using■SST■or■a■USB■memory.
7
Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Description
7 Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Error■ Detail■
Location Item
code Code
E614 FF01 00 Title Flash■PCB■error
Detection■ Flash■error■(Unidentified)■(Initialization■failed■at■startup■or■I/O■
description error■at■startup)
When■this■error■occurs,■the■system■has■not■been■started■normally.■
Therefore,■it■may■not■be■recorded■in■the■error■log.
Remedy [Related■parts]
•■ Flash■PCB■(UN61)
•■ Main■Controller■PCB■(UN05)■(Unit■of■replacement:■MAIN■
CONTROLLER■PCB■ASS'Y)
[Remedy]■Perform■the■following■in■the■order■while■checking■
whether■the■error■is■cleared.
•■ Although■the■error■is■cleared■by■"HD-CHECK",■it■may■occur■
again.■Thus,■perform■Remedies■1■to■3.
•■ Reinstall■the■necessary■application■software■and■restore■the■
backup■data■once■the■error■is■cleared.
1.■Select■COPIER>■FUNCTION>■SYSTEM>■CHK-TYPE>■"0",■
and■execute■"HD-CHECK".■Then,■turn■OFF■and■then■ON■the■
main■power.
2.■Obtain■the■necessary■backup■data■by■referring■to■the■backup■
data■list.
3.■Select■COPIER>■FUNCTION>■SYSTEM>■CHK-TYPE>■"0",■
and■execute■"HD-CLEAR".■Then,■turn■OFF■and■then■ON■the■
main■power.
[Reference]■All■the■partitions■that■can■be■deleted■are■deleted.
4.■Enter■safe■mode■using■(2+8)■startup,■and■execute■[4]■Clear/
Format>■[2]■Flash■Format■(Flash■format)■using■a■USB■memory.
5.■After■replacing■the■Flash■PCB,■reinstall■the■system■software■
using■SST■or■a■USB■memory.
6.■Replace■the■Main■Controller■PCB.
[Reference]■For■backup■and■restoration,■refer■to■"Adjustment>■
Actions■after■Replacement"■and■"Appendix>■Backup■Data■List"■in■
the■Service■Manual.
7-90
Description
7-90