Canon imageRUNNER ADVANCE C3325 Series Service Manual page 702

COPIER > OPTION > IMG-FIX
TMP-TB12 Set fixing control temp: plain paper 3
Lv.1 Details To set the offset of fixing control temperature for plain paper 3 (91 to
105 g/m2).
As the value is changed by 1, the control temperature is changed by 5
deg C.
Increase the value when a fixing failure occurs, and decrease the value
when fixing offset occurs.
Use case When a fixing failure/fixing offset occurs on plain paper 3
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
TMP-TB13 Set fixing control temp:recycled paper 2
Lv.1 Details To set the offset of fixing control temperature for recycled paper 2 (76
to 90 g/m2).
As the value is changed by 1, the control temperature is changed by 5
deg C.
Increase the value when a fixing failure occurs, and decrease the value
when fixing offset occurs.
Use case When a fixing failure/fixing offset occurs on recycled paper 2
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
8
Service Mode > COPIER > OPTION > IMG-FIX
8 Service Mode > COPIER > OPTION > IMG-FIX
COPIER > OPTION > IMG-FIX
TMP-TB11 Set fixing control temp:recycled paper 1
Lv.1 Details To set the offset of fixing control temperature for recycled paper 1 (64
to 75 g/m2).
As the value is changed by 1, the control temperature is changed by 5
deg C.
Increase the value when a fixing failure occurs, and decrease the value
when fixing offset occurs.
Use case When a fixing failure/fixing offset occurs on recycled paper 1
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -3 to 2
-3: -15 deg C, -2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2:
+10 deg C
Unit 5 deg C
Default value 0
FXS-TM11 Set ITOP control temp: recycled paper 1
Lv.1 Details To set the offset of ITOP control temperature for recycled paper 1 (64
to 75 g/m2).
As the value is changed by 1, the control temperature is changed by 5
deg C.
Decrease the value when uneven gloss occurs, and increase the value
when a fixing failure occurs on the leading edge of paper.
Use case - When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (74 mm)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution If the value is too large, uneven gloss may occur.
If the value is too small, a fixing failure may occur on the leading edge
of paper. (Toner does not peel off.)
Display/adj/set range -3 to 2
-3: -15 deg C, -2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2:
+10 deg C
Unit 5 deg C
Default value 0
8-151
8-151