Canon imageRUNNER ADVANCE C3325 Series Service Manual page 624

COPIER>ADJUST>COLOR
OFST-Y Adj Y-clr brit area dens&color balance
Lv.1 Details To adjust the bright area density and color balance of Y-color.
As the value is larger, the image gets darker.
Decrease the value when the background cannot be read correctly
because the density of a document is dark and increase the value
when the density of a document is light.
Decrease the value when removal of the background is not performed
correctly and a fogging-like image appears.
Use case - When the background of a document cannot be read correctly
- When removal of the background cannot be performed correctly and
a fogging-like image appears
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -32 to 32
Default value 0
OFST-M Adj M-clr brit area dens&color balance
Lv.1 Details To adjust the bright area density and color balance of M-color.
As the value is larger, the image gets darker.
Decrease the value when the background cannot be read correctly
because the density of a document is dark and increase the value
when the density of a document is light.
Decrease the value when removal of the background is not performed
correctly and a fogging-like image appears.
Use case - When the background of a document cannot be read correctly
- When removal of the background cannot be performed correctly and
a fogging-like image appears
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -32 to 32
Default value 0
OFST-C Adj C-clr brit area dens&color balance
Lv.1 Details To adjust the bright area density and color balance of C-color.
As the value is larger, the image gets darker.
Decrease the value when the background cannot be read correctly
because the density of a document is dark and increase the value
when the density of a document is light.
Decrease the value when removal of the background is not performed
correctly and a fogging-like image appears.
Use case - When the background of a document cannot be read correctly
- When removal of the background cannot be performed correctly and
a fogging-like image appears
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -32 to 32
Default value 0
8
Service Mode > COPIER > ADJUST > COLOR
8 Service Mode > COPIER > ADJUST > COLOR
COPIER>ADJUST>COLOR
OFST-K Adj Bk-clr brit area dens&color balance
Lv.1 Details To adjust the bright area density and color balance of Bk-color.
As the value is larger, the image gets darker.
Decrease the value when the background cannot be read correctly
because the density of a document is dark and increase the value
when the density of a document is light.
Decrease the value when removal of the background is not performed
correctly and a fogging-like image appears.
Use case - When the background of a document cannot be read correctly
- When removal of the background cannot be performed correctly and
a fogging-like image appears
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -32 to 32
Default value 0
LD-OFS-Y Adj Y low dens area clr balance: copy
Lv.2 Details To adjust the color balance of the low density area of Y-color for copy
operation.
As the value is larger, the image gets darker.
A value obtained by adding the value adjusted in [Fine Adjust Density]
in the main menu to the setting value of this item is applied as the
actual density value.
e.g.: When the value of this item is "-4" and the value of [Fine Adjust
Density] is "5", the density value is "1".
Note that the density value must be within the rage from -8 to 8.
e.g.: When the value of this item is "7" and the value of [Fine Adjust
Density] is "5", the density value is "8".
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -8 to 8
Default value 0
Related user mode Copy> Options> Color Balance> Fine Adjust Density
Access Stored Files> Mail Box> Print> Change Print Settings>
Options> Color Balance> Fine Adjust Density
Supplement/memo In the main menu, different density values can be set for copy
operation and file storage. Although the setting value of this item is just
one value, the density may differ for copy operation and file storage.
8-73
8-73