Canon imageRUNNER ADVANCE C3325 Series Service Manual page 635

COPIER>ADJUST>HV-TR
TR-ENV1 Sec trns indiv setting environment:set 1
Lv.2 Details To set the environment (absolute moisture content) for setting 1.
Setting 1 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV1, TR-PPR1 and
TR-DUP1. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL1 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR1, TR-DUP1, TR-VL1, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV2 Sec trns indiv setting environment:set 2
Lv.2 Details To set the environment (absolute moisture content) for setting 2.
Setting 2 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV2, TR-PPR2 and
TR-DUP2. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL2 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR2, TR-DUP2, TR-VL2, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8
Service Mode > COPIER > ADJUST > HV-TR
8 Service Mode > COPIER > ADJUST > HV-TR
COPIER>ADJUST>HV-TR
TR-ENV3 Sec trns indiv setting environment:set 3
Lv.2 Details To set the environment (absolute moisture content) for setting 3.
Setting 3 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV3, TR-PPR3 and
TR-DUP3. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL3 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR3, TR-DUP3, TR-VL3, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
TR-ENV4 Sec trns indiv setting environment:set 4
Lv.2 Details To set the environment (absolute moisture content) for setting 4.
Setting 4 is the combination condition of environment, paper type (paper
weight), color mode/feed side that are set in TR-ENV4, TR-PPR4 and
TR-DUP4. When this condition is satisfied, the paper allotted voltage
adjusted in TR-VL4 is applied at the time of secondary transfer.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image, etc.)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2:
Normal humidity (6.12 to 15.68 g/m3), 3: High humidity (15.69 g/m3 or
higher)
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-PPR4, TR-DUP4, TR-VL4, 2TR-OFF
Supplement/memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting
1 to 16). When there is more than one setting where all conditions
(environment, paper type and color mode/feed side) are the same, the
setting with a smaller setting number is applied.
8-84
8-84