1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Network Hardware
  5. JetFusion Integrated Access Device
  6. User manual

Paradyne JetFusion Integrated Access Device User Manual

Integrated access device
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
JetFusion
Integrated Access Device
User's Guide
Document No. 2000-A2-GB20-10
February 2004

Advertisement

Table of Contents
loading

Related Manuals for Paradyne JetFusion Integrated Access Device

Summary of Contents for Paradyne JetFusion Integrated Access Device

  • Page 1 JetFusion Integrated Access Device User’s Guide Document No. 2000-A2-GB20-10 February 2004...
  • Page 2 Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.) Telephone: Call our automated system to receive current information by fax or to speak with a company representative.

  • Page 3: Table Of Contents

    Preface Audience... xi Contents ... xi Safeguards ...xii Product Warranty...xiii Conventions...xiii Regulatory Notices ...xiii Chapter 1 Data Interfaces ... 2 JetFusion 2/4/8-Port IAD Family... 2 Front Panel Power and Status Indicators... 3 Rear Panel Connectors... 4 JetFusion 16/24-Port IAD Family... 4 Front Panel Power and Status Indicators...
  • Page 4 Basic IAD Configur-ation ... 19 Connecting LAN, WAN, USI and Telephones... 19 Ethernet LAN Connection ... 19 WAN Connections ... 19 USI Connection (16/24-Port) ... 20 Telephone Connections... 20 Confirming Proper Setup ... 21 Chapter 3 IAD Security... 23 RADIUS Server Settings ... 26 Setting Up SNMP ...
  • Page 5 Configuring the G.SHDSL Interface... 56 Configuring the SDSL Interface—JF2100 ... 59 Configuring the SDSL Interface... 60 Configuring the ADSL Interface... 64 Setting the Interface to T1 or E1... 65 Configuring the T1 Interface ... 66 Configuring the E1 Interface... 71 Configuring ATM PVCs...
  • Page 6 Managing Static and Default Routes ... 103 Setting the Default Route ... 105 Configuring DNS Client ... 106 Configuring DHCP Client... 107 Configuring DHCP Relay... 108 Configuring the Telnet Server Port ... 109 Configuring IP Filtering ... 109 Configuring IP Header Compression (IPHC)... 116 Configuring the LAN IP Broadcast Destination...
  • Page 7 Voice Path Configuration Menu ... 128 Setting the Voice Gateway ... 128 Setting Jitter Delay ... 130 Displaying Jitter Delay ... 130 Setting Start Mode ... 130 Setting SLIC Control Mode... 132 Setting Compander Mode... 132 Set On Hook Transmission Mode... 133 Setting Idle Voltage Mode...
  • Page 8 Configuring a DHCP Client Entry ... 158 Displaying DHCP Server Details ... 160 Displaying DHCP Server Statistics ... 161 Displaying DHCP Server Assigned and Unassigned Addresses161 Displaying DHCP Entry Details ... 162 Deleting a DHCP Client Entry... 162 Deleting a DHCP Assign-ment Entry... 162 Chapter 10 Multicast Configuration Configuring Multicast ...
  • Page 9 NAT Connection Table... 177 NAT Connection Details ... 177 NAT Local Server Table... 179 NAT Alias Table ... 179 Deleting IP Addresses from NAT Tables ... 179 Deleting a NAT Local Server Entry... 180 Deleting a NAT Alias Entry ... 180 Chapter 12 IAD Reports The Report Menu...
  • Page 10 remove lan ip address ... 224 set bridge global ... 224 set bridge stp global ... 225 set dhcp server enable ... 225 set dhcp server gateway... 225 set dhcp server subnet ... 225 set dhcp server dns ... 225 set dhcp server netbios ...
  • Page 11 set wan ip address... 234 set wan stp bridge ... 234 set wan rip ... 235 show configuration... 235 show dhcp server configuration... 235 show ip routes ... 235 tftp receive ... 235 Chapter 14 Troubleshooting and Diagnostics Using the Diagnostics Menu ...
  • Page 12 16/24-Port... 262 Appendix D Connector Pinouts ... 265 Appendix E Glossary ... 268 Index 2000-A2-GB20-10 Connector Pinouts Glossary - x - February 2004...

  • Page 13: Audience

    The JetFusion Family IAD User Guide contains the information you need to install, connect and configure each JetFusion IAD in a customer’s premises. Audience This guide is intended for network engineers and other professionals in the telecommunications industry who are engaged in the installation, configuration, management and support of telephone and computer networks, network access products, and related equipment.

  • Page 14: Safeguards

    Chapter 8, setting up the IAD to perform IP filtering. Chapter 9, the steps required to configure the Dynamic Host Configuration Protocol (DHCP) server and client. Chapter 10, configure the IAD to perform Network Address Translation (NAT). Chapter 11, to configure the IAD to perform Network Address Translation (NAT). Chapter 12, Chapter 13, and exit CLI mode, and how to use each command in the command line...

  • Page 15: Product Warranty

    ‹ Do not disassemble this system (except as instructed in the manufacturer’s instructions). To reduce the risk of shock and to maintain the warranty on the system, a qualified technician must perform service or repair work. ‹ Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
  • Page 16 ‹ Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Paradyne could void the user’s authority to operate this equipment. The JetFusion models below comply with Part 68 of the FCC Rules. On...
  • Page 17 Your telephone company may make changes in its facilities, equipment, operations, or procedures that could effect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with the IAD, please contact your service provider for information on obtaining service or repairs.
  • Page 18 CE Mark These JetFusion products have been marked with the CE mark. This mark indicates compliance with EEC Directives 89/336/EEC, 73/23/EEC 1999/ 5/EC. Warning All JetFusion products except JF2004 are Class A products. In a domestic environment these products may cause radio interference in which case the user may be required to take adequate measures A full copy of the declaration of Conformity can be obtained from Polyspan Ltd., Whichford House, Parkway Court, Oxford Business Park South,...
  • Page 19 Verklaring van overeenstemming: Hierbij verklaart Polyspan Ltd. dat diens JetFusion voldoet aan de basisvereisten en andere relevante voorwaarden van EG-richtlijn 1999/5/ Declaração de Conformidade: Através da presente, a Polyspan Ltd. declara que este JetFusion se encontra em conformidade com os requisitos essenciais e outras disposições relevantes da Directiva 1999/5/CE.
  • Page 20 This chapter introduces the JetFusion Integrated Access Devices (IAD) and describes their hardware and software. You should be aware of the characteristics of each IAD to properly install and configure them for operation in a customer’s premises. This chapter provides information about these topics: ‹...

  • Page 21: Data Interfaces

    MetaLink, and Globespan chip sets. These include Lucent Stinger/ TNT, Nokia Speedlink System, Promatory IMAS, AccessLan PacketLoop, Accelerated Networks AN-3200, CopperMountain CopperEdge, and Paradyne GranDSLAM DSLAMs, for example. ‹ Seamless voice and high-speed data integration over xDSL or T1/E1 ‹...

  • Page 22: Front Panel Power And Status Indicators

    ‹ JF2304 and JF2308 IADs—provide voice services and high-speed Internet or corporate connectivity over SDSL, and provide 4 or 8 voice ports. Physical and electrical specifications for each IAD are listed in Appendix JetFusion IAD Specifications Front Panel Power and Status Indicators The front panel of the IAD contains several LEDs.

  • Page 23: Rear Panel Connectors

    Rear Panel Connectors On the rear panel type and position of the WAN and telephone connectors vary by IAD. Figure 1–3. Typical 2/4/8-Port Family Back Panel Connectors Power Receptacle DC Power Adapter Connects the IAD to any AC outlet of 90-250 volts via an external, 18 volt power supply.

  • Page 24: Front Panel Power And Status Indicators

    MetaLink, and Globespan chip sets. These include Lucent Stinger/ TNT, Nokia Speedlink System, Promatory IMAS, AccessLan PacketLoop, Accelerated Networks AN-3200, Coppermountain CopperEdge, and Paradyne GranDSLAM DSLAMs, for example. ‹ Seamless voice and high-speed data integration over xDSL or T1/ITE1 ‹...

  • Page 25: Rear Panel Connectors

    Table 1–2. Front Panel LEDs POWER LAN LINK LAN ACT WAN LINK VOICE DCE LINK DCE ACT Rear Panel Connectors On the rear panel, the IAD contains several connectors. The WAN connectors vary by IAD—both are present, but one has a permanently attached metal shield to prevent use.
  • Page 26 V.35, Black Box Corporation provides a cable (FA058) for conversion purposes. To convert from RS-530 to RS-449, Black Box provides a cable EDN57J. By notifying you of their availability, Paradyne neither endorses or recommends these products. For USI port pinouts when configured as RS-530, V.35 or RS-449, see Table D–9...
  • Page 27 This chapter describes the steps to install, connect, and set the IP address of the JetFusion IAD. It introduces the menu interface and describes how to perform basic configuration for common LAN and WAN environments. It also describes basic operations—resetting the IAD, and logging off. In many cases, all the information you need to get an IAD up and running in a customer’s premises is contained in this single chapter.

  • Page 28: Unpacking The Iad

    Unpacking Each IAD is packed and shipped in a durable container. If you haven’t already done so, open the container and unpack the IAD. Carefully the IAD remove the IAD from the package and packing material. IAD Package Components Each IAD is shipped with the components listed below. As you unpack them, note their condition and identity, and compare the list to the packing list in the package.

  • Page 29: Connect Via Terminal Emulator

    vertically, ensure at least 3 inches of distance between other IADs or other equipment. NOTE Wiring Requirements Make sure that the telephone wiring, LAN and WAN cables reach the IAD and can be dressed in a manner that is safe for the wiring, does not pull or create lateral stress on the connectors or ports on the rear of the IAD, and does not present a trip hazard to personnel working in the vicinity of the equipment.
  • Page 30 switch, located on the back panel. This starts the IAD and it executes the boot process to begin normal operation. 2. Verify that the Power indicator on the front panel illuminates. NOTE Log in via a Terminal Emulation Program With a serial cable connected, follow these steps to log in to the IAD: 1.

  • Page 31: Setting The Ethernet Port Ip Address

    9. Press any key, and repeat the log in sequence. If you cannot log in, call your support provider for assistance. When you first log in, the IAD displays the Main menu. The menu may vary, depending on the IAD. Figure 2–1.
  • Page 32 Figure 2–2. Router Configuration Menu ***************************************** ***************************************** C. Configure Port IP Address U. Unconfigure Port IP Address M. Configure Port Max Transmission Unit S. Add/Remove a Static Route R. Enable/Disable RIP V. Configure RIP Version by Port P. Configure RIP Poisoned Reverse by Port N.

  • Page 33: Resetting The Iad

    Type the new subnet mask (usually 255.255.255.0) and press Enter. 7. The IAD displays the following instructions: Select priority Normal/High [N/H] (N): Give the interface normal priority—type N or press Enter. 8. Type Y or Enter to save the new IP address and subnet mask. 9.

  • Page 34: Connecting Via Telnet

    Connecting To manage the IAD via the LAN (or Intranet), you must set an IP address for the Ethernet port before you can use Telnet to access the IAD. via Telnet NOTES Running Telnet Before you use Telnet to log in to the IAD, make sure that the IAD and your PC are connected to the same network via straight-through Ethernet cables (or directly connected via a cross-over cable), and you know the IP address of the IAD.

  • Page 35: Using The Menu Interface

    4.Type your password and press Enter to display the Main menu. ***************************************** ***************************************** 1. Reports Menu 2. Configure IP Router 3. Configure Bridge 5. Configure WAN 6. Configure LAN 7. Configure SNMP 8. Configure Login 9. System Utilities D. Configure DHCP Server N.
  • Page 36 Figure 2–4. Main Menu for Supervisor ***************************************** ***************************************** 1. Reports Menu 2. Configure IP Router 3. Configure Bridge 5. Configure WAN 6. Configure LAN 7. Configure SNMP 8. Configure Login 9. System Utilities D. Configure DHCP Server M. Configure Multicast N.
  • Page 37 Navigating the IAD Menu Interface Menus in the IAD configuration system are arranged hierarchically. That is, you select single-key options to navigate down to display specialized menus and specific tasks, and press the Escape key successively to return back to menus higher in the interface. The specific menus, submenus and commands that display depend on the interfaces for the specific IAD, the options configured and the security level that you use to log in.

  • Page 38: Basic Iad Configur-Ation

    Exiting the Menu Interface To exit the menu interface, return to the Main menu using the Escape key, and press Escape one more time. The IAD asks you to confirm—press Y to exit (or press Return to accept the default value (N) to cancel the exit). After exiting, you can quit the terminal emulator or Telnet application.

  • Page 39: Usi Connection (16/24-Port)

    Making G.SHDSL Connections G.SHDSL-equipped IADs use an RJ11 connector on the rear panel for WAN connection. To make the connection, plug the WAN cable into the RJ11 WAN connector. connector pinouts. Making SDSL or ADSL Connections SDSL- and ADSL-equipped IADs use an RJ45 connector on the rear panel for WAN connection.

  • Page 40: Confirming Proper Setup

    Making RJ21X Connections (16/24-Port) The pin assignments for the RJ21X connector are telco standard. Connect telephone devices from an RJ11 jack field, or a punch down block. Each line provides a two-wire loop or groundstart connection. To perform the connection, use a customer-provided cable terminated at one end with an RJ21X connector.
  • Page 41 This chapter describes how to control security to your IAD, validate users using a RADIUS server, configure SNMP via IP or EOC, upgrade IAD software, and perform other general and utility-oriented tasks. This chapter includes these topics: ‹ IAD security—setting user IDs and passwords (page 23) ‹...

  • Page 42: Iad Security

    Network Administrator and Supervisor level may not be modified. The password for each security level may be changed. Although you may use the same password for all security levels, Paradyne recommends that you use a different one for each level.
  • Page 43 Table 3–2 Table 3–2. Default User IDs and Passwords Security Level User Network Administrator Supervisor The user ID and password may contain up to 17 alphanumeric characters. These values are case sensitive; spaces and punctuation characters are not allowed. NOTE Changing a Password To change a password at any security level, you must sign on at or above the security level you’re changing and follow these steps:...
  • Page 44 Changing the User Level User ID To change the user ID for the User security level (the only security level that allows the user ID to be changed), follow these steps: 1. On the Main menu, type 8 (Configure Login) to display the Password Configuration menu.

  • Page 45: Radius Server Settings

    Enter new Primary/Secondary RADIUS Encryption Secret 3. Type the new encryption key and press Enter. 2000-A2-GB20-10 Paradyne does provide a RADIUS server. You must provide a RADIUS server to use this feature. For more information on RADIUS servers, see RFC 2865.
  • Page 46 4. Reset the IAD (page 14). Displaying the RADIUS Configuration To display the current RADIUS server configuration: 1. On the Main menu, select Configure Login to display the Password Configuration menu (page 24). 2. Type 9 to select Display RADIUS Configuration. The IAD displays the following information: Primary RADIUS Server: Primary RADIUS Secret:...

  • Page 47: Setting Up Snmp

    Setting Up You can enable SNMP over IP and/or EOC (when the voice gateway is AAL2/LES CAS or ELCP). By default, the IAD is configured with SNMP SNMP disabled. When SNMP is enabled and the settings are configured, you can use SNMP to remotely manage the IAD by getting and setting IAD values, and monitoring IAD events.
  • Page 48 Type P to configure system contact (up to 39 alphanumeric characters): 1. The IAD displays the current system contact and prompt: System Contact is currently: Paradyne Enter new System Contact > Type the name of the new contact person or department and press Enter.
  • Page 49 Configuring the System Name Type N to configure the system name (up to 39 alphanumeric characters): 1. The IAD displays the current system name and prompt: System Description is currently: Enter new System Description > Type the new system name and press Enter. 2.
  • Page 50 Enabling or Disabling SNMP Traps via EOC Type U to enable or disable SNMP traps via EOC: 1. The IAD displays the current status and prompt: SNMP traps sent via EOC are currently DISABLED To enable traps via EOC, type E. To disable them, type D. 2.

  • Page 51: Upgrading The System

    Upgrading Periodically, Paradyne may provide new software that you will download to the IAD to upgrade the system. You must use TFTP to perform the file the System transfer when upgrading the entire system. NOTE To use TFTP, you must configure both the IAD and the computer that contains the TFTP Server program, a program that you license separately.
  • Page 52 2. Type X to display the File Transfer menu. Figure 3–4. File Transfer Menu ******************************************* ******************************************* B. Load Boot ROM O. Update ACOS [acos.bin] X. Update Entire System A. File Transfer Utilities 3. Type X to update the entire system (you must use TFTP). Respond by typing Y to continue.

  • Page 53: Setting Up Your Lan Connection

    Setting up The IAD LAN port may be set for full duplex Ethernet operation if your IAD is set up as a router. Full duplex mode allows simultaneous transmission Your LAN and receipt of Ethernet packets. Connection On the Main menu, type 6 (Configure LAN) to display the LAN Configuration menu.

  • Page 54: Using System Utilities

    Using The Utilities menu contains utility commands, and several menus to upgrade ACOS software and support ACOS application development. System To display the Utilities menu, type 9 on the Main menu. 16/24-port IADs Utilities display a menu with option U, the USI port command: Figure 3–6.
  • Page 55 Using Trace Route Use Trace Route to trace the network route to a specified host. To run Trace Route, follow these steps: 1. Type X on the Utilities menu and press Enter. 2. Type the IP address or host name to trace and press Enter. If you enter a host name, you must enter the domain name with the host name.

  • Page 56: Managing Configuration Files

    1. Type V on the Utilities menu to display this message and prompt: Console timeout is currently disabled. Enter new console timeout in minutes, 0 to disable timeout. (0-60) [0]: 2. Type the timeout value—a value between 0-60 minutes (default 3), and press Enter.
  • Page 57 3. The IAD displays the following: WARNING: Saving System settings as Custom Defaults Press Y to Save Defaults-> Type Y to confirm the process. 4. The IAD updates the setting and displays the Utility menu. 5. Reset the IAD (page 14) to reboot with the new config file. Saving System Settings To override the factory-supplied default.st config file with the current config.st file, follow these instructions:...

  • Page 58: Using The File System

    Using the The File System menu contains commands to manage files on the IAD. To display the File System menu, type F on the Utilities menu. File System Figure 3–7. File System Menu *************************************************** *************************************************** D. Directory of all files C.
  • Page 59 CAUTION Formatting the File System Reformatting the file system permanently removes all files in the IAD. This command is reserved for use by Paradyne network engineers. NOTE Displaying Free Space in the File System To display the amount of free space in the file system (flash memory), type S on the File System menu.

  • Page 60: Using The Debug Menu

    2. Type E to enable PPP debugging, or type D to disable it. The IAD sets PPP debug mode to the setting you entered, and displays the Debug menu. 2000-A2-GB20-10 Debugging commands are reserved for use by Paradyne network engineers. Debug Menu = *-**-**-**-**-**...
  • Page 61 Enabling and Disabling STP Debug Mode When you enable STP debugging, the IAD displays STP debug messages. To enable or disable STP debugging, follow these steps: 1. Type S on the Debug menu. The IAD displays the STP debug status: STP Debug Mode is currently DISABLED 2.

  • Page 62: Performing File Transfers

    Performing The File Transfer menu allows you to transfer groups of files to or from the IAD. To display the File Transfer menu, type X on the Utilities menu. File Transfers Figure 3–10. File Transfer Menu *************************************************** *************************************************** B. Load Boot ROM O.

  • Page 63: Using File Transfer Utilities

    Updating ACOS Type O on the File Transfer menu to display the File Transfer Method menu and download the Atlas Communications Operating System (ACOS) to the file system in Flash memory on the IAD. The file is stored on the IAD as acos.bin.
  • Page 64 Type the name of the file and press Enter. To exit without transferring the file, press Escape or Enter without typing the file name. 4. When XMODEM is selected, if the file is not located, the IAD prompts you for the file transfer speed. 5.

  • Page 65: Setting Derived Timing Options

    2. Enable/Disable *PSTN ONLY* Derived Timing Debug Messages 3. Enable/Disable *Local Clock ONLY* Derived Timing Debug Messages 2000-A2-GB20-10 Derived Timing The Derived Timing debugging messages are reserved for use by Paradyne network engineers. Derived Timing Debug - 46 - February 2004...

  • Page 66: Verifying An Ip Address

    2. Type 1, 2, or 3 to enable or disable specific derived timing debugging messages. For each option, the IAD displays the Derived Timing Debug menu. 2. Type 1 to enable debug messages, or 2 to disable debug messages. 3. Reset the IAD (page 14). Verifying When operating the IAD in a network, there are several different IP addresses you should be aware of:...

  • Page 67: Basic Wan Setup Tasks

    This chapter describes how to configure the IAD WAN interface and datalink protocol for data operation. ‹ Basic WAN setup tasks (page 48) ‹ Using the WAN Configuration menu (page 52) ‹ Selecting the Datalink Protocol (page 53) ‹ Selecting the Physical Interface (page 55) ‹...
  • Page 68 Figure 4–1. xDSL WAN Configuration Flowchart SDSL Module Changing factory configuration Select quick ATM? configuration Define PVCs Frame ATM? Relay? Configure Define PVCs Define DLCIs Frame ATM options Relay? Configure Define DLCIs maintenance ATM options protocol 0232 maintenance protocol 2000-A2-GB20-10 - 49 - February 2004...
  • Page 69 Figure 4–2. T1/E1 WAN Configuration Flowchart Define PVCs Configure ATM options 2000-A2-GB20-10 T1/E1 Interface Set datalink protocol Set physical interface Frame Relay Define DLCIs maintenance protocol - 50 - February 2004...
  • Page 70 Identifying your WAN Interface and Datalink Protocol The sections you’ll use to perform WAN configuration depend on the IAD model and the datalink protocol you choose. Voice and data traffic are each carried in their own PVCs (ATM protocol) or DLCIs (Frame Relay protocol).

  • Page 71: Using The Wan Configuration Menu

    JF2304 6300 JF2308 POWER LAN LINK LAN ACT WAN LINK VOICE JF2316 JF2304 POWER LAN LINK LAN ACT WAN LINK VOICE JF2104 JF2104i POWER LAN LINK LAN ACT WAN LINK VOICE JF2108 Using the Configuring the IAD for data involves several tasks. Tasks in this chapter are described beginning at the WAN Configuration menu (which varies, WAN Con- based on the WAN interface and datalink protocol).

  • Page 72: Selecting The Datalink Protocol

    NOTE Selecting If you are setting up voice and data channels, you can select ATM or Frame Relay as you set up the channels, in the section Setting Up TDM the Datalink Voice, following. Protocol To select ATM or Frame Relay as the datalink protocol: 1.

  • Page 73: Setting Up Tdm Voice

    Figure 4–6. WAN Configuration Menu (Frame Relay) ***************************************** ***************************************** Configuring G2237 xDSL 1. Configure Datalink Protocol 2. Configure Physical Interface 3. Configure DLCIs 4. Configure FR Options 3. Reset the IAD (page 14) when you finish WAN configuration. Setting Up TDM Voice allows you to set up data and voice circuits on channelized T1 circuits.

  • Page 74: Selecting The Physical Interface

    Enter number of voice channels desired for this chunk: Type the number of voice channels. 5. The IAD asks you for the starting channel: Enter the starting channel of this voice channel chunk: Type the starting channel number for this chunk of circuits. 6.

  • Page 75: Configuring The G.shdsl Interface

    1. Type 1 (Configure Physical Interface) to display the G2237 xDSL Configuration menu. Figure 4–8. G2237 xDSL Configuration menu ****************************************** ****************************************** Current Interface Type is: G.SHDSL-A. Mode: CPE, Rate Mode: FIXED, Line Rate: 88K, Debug: DISABLED. 1. Select xDSL Interface Type 2.
  • Page 76 Figure 4–10. G2237 xDSL Configuration Menu ****************************************** ****************************************** Current Interface Type is: G.SHDSL-A. Mode: CPE, Rate Mode: FIXED, Line Rate: 88K, Debug: DISABLED. 1. Select xDSL Interface Type 2. Select CPE/CO Mode 3. Enable/Disable Adaptive Rate Mode 4. Select Line Rate D.
  • Page 77 3. Reset the IAD (page 14) when you finish WAN configuration. Enabling and Disabling xDSL Debug Messages NOTE 2000-A2-GB20-10 Configure CPE/CO Mode Configure G.SHDSL Rate Mode Option D, Enable/Disable G2237 xDSL Debug Messages, is reserved for Paradyne network engineers. - 58 - February 2004...

  • Page 78: Configuring The Sdsl Interface-Jf2100

    Configur- The tasks described in this section all begin on the G2237 xDSL Configuration menu. The tasks are described so you can proceed through ing the them sequentially. You should review and update each of these options as SDSL Inter- necessary, and reset the IAD when you finish WAN configuration.

  • Page 79: Configuring The Sdsl Interface

    VOICE JF2316 2000-A2-GB20-10 Configure SDSL Rate Mode Option D, Enable/Disable G2237 xDSL Debug Messages, is reserved for Paradyne network engineers. This section is for configuring the SDSL WAN interface on the JF2304, JF2308 or JF2316. - 60 - February 2004...
  • Page 80 Figure 4–16. SDSL Configuration Menu ****************************************** ****************************************** Configuring SDSL Current SDSL configuration: CPE, AUTO Cycle, Bit Order: Sign.Mag, SPEED = 1152 Kbps, Conexant AutoBaud: Disabled 1. Toggle SDSL Mode (CO or CPE) 2. Set SDSL Speed to Auto Cycle (Nokia) 3.
  • Page 81 2. The IAD Displays the current setting and a prompt: Conexant AutoBaud Mode is currently DISABLED Enter E to Enable, D to Disable: Type E to enable or D to disable Autobaud mode and Sync Delay. 3. The IAD saves the configuration and displays the SDSL Configuration menu.
  • Page 82 Setting SDSL Speed for IMAS DSLAM—Nortel DSLAM 1. Type 7 to set the SDSL first try speed for connecting to an IMAS (Nortel) DSLAM. 2. The IAD displays the IMAS First Speed Option menu: Figure 4–18. IMAS First Speed Option Menu ****************************************** ****************************************** Select First Speed to Try...

  • Page 83: Configuring The Adsl Interface

    5. Multi-Mode 6. ADI 7. Alcatel 2000-A2-GB20-10 Commands in option D—SDSL Debug Menu—are reserved for Paradyne network engineers. This section is only for configuring the ADSL WAN interface on the JF2004, JF2008 and JF2004i. G7070 ADSL ATU-R Configuration - 64 -...

  • Page 84: Setting The Interface To T1 Or E1

    8. Configure Transmit Clock Source 9. Change to E1 Mode 2000-A2-GB20-10 Option D—ADSL Debug Messages—is reserved for Paradyne network engineers. This section is for configuring the IAD to use the T1 or E1 WAN interface on the JF2208 or JF2216 IAD. WAN Configuration Menu (Figure 4–22) or E1 Configuration menu...

  • Page 85: Configuring The T1 Interface

    Figure 4–23. E1 Configuration Menu ******************************************* ******************************************* 1. Select Frame/CRC4 Mode 4. Configure S-Bits 5. Configure Transmit Channels 6. Configure Receive Channels 7. Configure Clock Source 8. Change to T1 Mode P. Display Physical Layer Stats and Alarm Log Switching from T1 to E1 If your IAD is set for T1 and it is being deployed in an E1 environment: 1.
  • Page 86 Figure 4–24. T1 Configuration Menu ******************************************* ******************************************* 1. Select Frame Mode (D4 or ESF) 2. Select Transmit Line Build Out 4. Select B8ZS or AMI 5. Configure Loopback 6. Configure Transmit Channels 7. Configure Receive Channels 8. Configure Transmit Clock Source 9.
  • Page 87 Setting Line Build Out 1. Type 2 (Select Transmit Line Build Out) to display the Line Build Out menu. Figure 4–26. Select Line Build Out Menu ********************************** ********************************** Line Build Out Is 0 To 133 Feet 1. 0 To 133 Feet (Short haul) 2.
  • Page 88 Figure 4–27. Loopback Menu ************************************ Select Loopback Configuration ************************************ Outward Payload Loopback: DISABLED Outward Line Loopback: DISABLED Inward Loopback (Master Mode Only): DISABLED Line & Payload Loopback Command Receive (ESF Only): DISABLED 1. Enable/Disable Outward Payload Loopback 2. Enable/Disable Outward Line Loopback 3.
  • Page 89 Enabling or Disabling Specific Channels 1. Type 3 to enable or disable specific channels. If all channels are disabled, this option enables specific channels. Conversely, if all channels are enabled, this option disables specific channels. 2. The IAD displays this prompt: Select Channel to Enable/Disable, then press Enter.

  • Page 90: Configuring The E1 Interface

    Displaying Physical Layer Stats and Alarm Log The physical layer statistics displays the T1 error rate in errors per second for the past second. An event log (up to 5KB) is maintained for certain events. The time stamp is relative to the last system reset. As new events are added, older events are discarded when the file size is maximized.
  • Page 91 Figure 4–31. E1 Configuration menu ******************************************* ******************************************* 1. FAS 2. FAS (CRC4 Enabled) 3. Multi-Frame CAS 4. Multi-Frame CAS (CRC4 Enabled) Type the option to set the frame mode. 2. The IAD saves the configuration, resets the interface and displays the menu.
  • Page 92 Figure 4–33. Configure S-Bits Menu ******************************************* ******************************************* Current S-Bit Configuration: 3. To toggle a given bit, type the corresponding option number. 4. The IAD saves the configuration and displays the menu. 5. Continue setting S-bits. When you’ve finished, press Escape to return to the E1 Configuration menu and continue configuration tasks.
  • Page 93 Enabling or Disabling Specific Channels 1. Type 3 to enable or disable specific channels. If all channels are disabled, this option enables specific channels. Conversely, if all channels are enabled, this option disables specific channels. 2. The IAD displays this prompt: Select Channel to Enable/Disable, then press Enter.

  • Page 94: Configuring Atm Pvcs

    Displaying Physical Layer Stats and Alarm Log 1. Type P to display the physical layer statistics and the alarm log: Error Count Rates (Errors/s): Framing Bit Error Count Rate: 4000 CRC Error Count Rate: 0 Line Code Violation Count Rate: 0 Far End Block Error Count Rate: 1000 Rx Loss of Frame Count Rate: 0 Change Of Frame Alignment Rate: 0...
  • Page 95 Enter Virtual Port Identifier (VPI): Type a VPI value between 0 and 255 (default 0) and press Enter. 3. The IAD displays a prompt for the VCI: Enter Virtual Circuit Identifier (VPI): Type a VCI value between 32 and 65535 (default is 38 for data, 39 for voice) and press Enter.
  • Page 96 4. The IAD displays the ATM Encapsulation Configuration menu. Figure 4–37. ATM Encapsulation Configuration Menu ***************************************** ***************************************** Current Encapsulation: NONE 1. AAL5 (None) 2. AAL0 (None) 3. Proprietary Voice 4. RFC 1483 (using VC Muxing) 5. RFC 1483 (with LLC Encapsulation) 6.

  • Page 97: Modifying A Pvc

    7. The IAD saves the configuration and displays the PVC Configuration menu where you may continue with other PVC management tasks. 8. Reset the IAD (page 14) when you finish PVC configuration. Modifying a PVC To modify a PVC, follow these steps: 1.
  • Page 98 Figure 4–41. ATM Encapsulation Configuration Menu ***************************************** ATM Service Category Configuration ***************************************** Current Encapsulation: NONE 1. CBR 2. UBR Type 1 to select CBR for high priority data —or— Type 2 to select UBR for low priority data. 3. The IAD displays the Peak Cell Rate Configuration menu: Figure 4–42.
  • Page 99 To select CBR, type 1. To select UBR, type 2. 3. The IAD displays the Peak Cell Rate Configuration menu: Figure 4–44. ATM PCR Configuration Menu ******************************************* ATM Peak Cell Rate (PCR) Configuration ****************************************** Current line speed for this interface is 1544000 bps Please type a PCR value, or Press ENTER to accept allowed maximum PCR value for this line speed...
  • Page 100 RFC 1877 DNS Server Assignment for T1/E1, Port 1 is currently ENABLED Enter E to Enable, D to Disable: Type E to enable, or D to disable the DNS server assignment for T1 on this port. 6. The IAD reports the change, displays the status of the DNS server assignment for the port, and prompts you to enable or disable it: RFC 1877 Client configuration unchanged.
  • Page 101 Setting up AAL1/CES 1. The IAD displays the AAL2 Audio Profile Format menu: Figure 4–48. AAL2 Audio Profile Format Menu *********************************** *********************************** Current Audio Profile Format: NONE 1. ITU 2. ATM Forum To select ITU, type 1. 2. The IAD displays the AAL2 Audio Profile menu with available options: Figure 4–49.

  • Page 102: Deleting A Pvc

    Setting up AAL2/LES 1. The IAD displays the AAL2 Audio Profile Format menu: Figure 4–51. AAL2 Audio Profile Format Menu *********************************** *********************************** Current Audio Profile Format: NONE 1. ITU 2. ATM Forum To select ITU, type 1. 2. The IAD displays the AAL2 Audio Profile menu with available options: Figure 4–52.

  • Page 103: Showing Current Pvcs

    To delete the PVC, type Y, or cancel the deletion by typing any other character. 3. The IAD saves the configuration and displays the PVC Configuration menu where you may continue with other PVC management tasks. 4. Reset the IAD (page 14) when you finish PVC configuration. Showing Current PVCs To display a list of current PVCs, type 4.
  • Page 104 1. On the ATM Configuration menu, type 1 to select Configure Payload Scrambling. 2. The IAD displays the status and a prompt: Payload scrambling is DISABLE Enter E to Enable, D to Disable: To enable payload scrambling type E, or type D to disable payload scrambling.

  • Page 105: Configuring Frame Relay Dlcis

    Displaying F4 OAM Configuration To display the F4 OAM Type currently set, type 4. The IAD displays the status message, and then displays the ATM Configuration menu: F4 End to end OAM VPI 0 Sending OAM Loopback To send an OAM Loopback: 1.

  • Page 106: Modifying A Dlci

    ‹ Modifying an Existing DLCI ‹ Deleting a DLCI ‹ Showing Current DLCIs (page 90) You may configure up to 8 DLCIs on the IAD. NOTE Modifying a DLCI To modify a DLCI: 1. On the Frame Relay DLCI Configuration menu, type 2 to select Modify Existing DLCI.

  • Page 107: Adding A Dlci

    Adding a DLCI To add a DLCI: 1. On the Frame Relay DLCI Configuration menu, type 1 to select Add New DLCI. 2. The IAD displays the following prompt: Enter dlci number: Type a DLCI value between 16 and 1023 (default is 32 for data and 33 for voice) and press Enter.
  • Page 108 6. The IAD displays the throughput prompt: Enter the Circuit Throughput in bits/second (2048000): Type the circuit throughput and press Enter. 7. The IAD displays the excess burst prompt: Enter the excess burst size (Be) in number of bits (8): Type the excess burst value and press Enter.

  • Page 109: Deleting A Dlci

    16. If you type 2, the IAD displays the fragment size prompt: Enter maximum fragment size in bytes (100-1600) [0]: Type the fragment size in bytes and press Enter. 17. The IAD displays the End-to-End Fragmentation Configuration menu. Press Escape to return to the FR DLCI Config menu. 18.
  • Page 110 ‹ Configuring Maintenance Protocol (page 93) ‹ Configuring Congestion Parameters (page 93) ‹ Enabling or Disabling Coppermountain CMCP (page 94) Selecting Fragmentation Types To select which fragmentation to use: 1. On the Frame Relay Options menu, type 1 to display the FR Fragmentation Configuration menu.
  • Page 111 Enabling Automatic Fragment Sizing 1. Type 2 to enable automatic fragment sizing. 2. The IAD saves the configuration and displays the FR FRF.12 Configuration menu. Press Escape to continue. 3. Reset the IAD (page 14) when you finish Frame Relay configuration. Setting the Fragment Size Manually 1.
  • Page 112 Type the port number corresponding to the DLCI you want to set to real-time. 3. The IAD saves the configuration and displays the FR FRF.12 Configuration menu. Press Escape to continue. 4. Reset the IAD (page 14) when you finish Frame Relay configuration. Configuring the Maintenance Protocol To configure the maintenance protocol: 1.
  • Page 113 5. Reset the IAD (page 14) for changes to take effect. Toggling CMCP Debugging Option E (Toggle CMCP Debugging) displays when Coppermountain is selected as a Gateway, and is reserved for use by Paradyne and Coppermountain network engineers. This command enables and disables CopperMountain Control Protocol (CMCP) debugging.

  • Page 114: Quick Configuration

    1. Lucent Stinger (Conexant Autobaud, Payload Scrambling) 2. Nokia (Auto Cycle) 3. Coppermountain (Auto Sense) 4. Paradyne (Unframed 784kbps, Payload Scrambling) 5. AccessLan CPE 6. ATM (Unframed, 1152kbps fixed) 7. Frame Relay (784kbps fixed) 4. Type the option corresponding to the DSLAM to which the IAD is connected.
  • Page 115 This chapter describes how to configure the IAD as a router. You may configure the IAD as a router or a bridge, depending on your application. Optionally, you may also configure some ports for routing, and some ports for bridging. For example, you might set up PPP for Internet connections using routing, and set up a management connection using bridging.

  • Page 116: Basic Router Setup Tasks

    Basic To configure the IAD as a router, you should complete the following tasks: Router ‹ Configure IP addresses on the LAN and WAN ports (page 98) ‹ Setup Enable RIP poisoned reverse (recommended—page 101), add a static route (page 103), or add a default route (page 105) Tasks ‹...

  • Page 117: Router Configuration Menu

    Router Router tasks are all displayed and accessed on the Router Configuration menu (displayed by typing 2 on the Main menu). Tasks in this chapter are Configura- described beginning at the Router Configuration menu. tion Menu Figure 5–2. Router Configuration Menu ******************************************* ******************************************* C.
  • Page 118 Type the interface number to configure. 3. The IAD displays the port table for this interface and prompts for a port. Port VPI VCI Encapsulation Type Maximum PCR this interface can support = 3622 cps Select Port: [1-8] Type the port to configure and press Enter. 4.

  • Page 119: Unconfiguring A Port Ip Address

    8. Configuration is complete. The IAD displays the following prompt: Save new IP Information? ->(Y) Type Y to confirm your changes, or press Escape to cancel. 9. If you confirm, the IAD saves the settings. 10. If bridging is enabled and an IP address is assigned on the WAN interface, the IAD displays the IP Over Bridge prompt: Both bridging and IP address are specified for this interface.

  • Page 120: Setting The Port Maximum Transmission Unit

    Setting the The MTU setting controls IP fragmentation of packets transmitted through the specified port. Packet whose size is greater than the MTU value are Port Maxi- fragmented to fit into the MTU size limit. To set a maximum transmission unit value for a port, follow these steps: Transmis- 1.

  • Page 121: Setting The Rip Version

    1. Type P on the Router Configuration menu to select Configure RIP Poisoned Reverse by Port. 2. The IAD displays the interfaces on this IAD (sample shown): Available Interfaces: 1. SDSL 2. 10/100BaseT Ethernet 0. (Abort) Type the number of the port to enable or disable. 3.

  • Page 122: Managing Static And Default Routes

    5. Setting the RIP version for this port is complete. The IAD saves the settings and displays the Router Configuration menu. 6. Repeat these steps for each remaining port to set. 7. Continue with other configuration tasks, or press Escape to return to the Main menu.
  • Page 123 9. Continue with other configuration tasks, or press Escape to return to the Router Modification menu. 10. Reset the IAD (page 14) when you finish router configuration. 2000-A2-GB20-10 - 104 - February 2004...

  • Page 124: Setting The Default Route

    Removing a Static Route To delete a static route from the Route Table: 1. On the Router Modification menu type R to select Remove a Route. 2. The IAD prompts for the address of the route to remove: Enter address of static route to remove: Type the IP address of the route to remove and press Enter.

  • Page 125: Configuring Dns Client

    Configur- DNS Client allows the IAD to use fully-qualified domain names; for example, www.paradyne.com. To configure the IAD as a DNS Client, type ing DNS N on the Router Configuration menu. The IAD displays the DNS Client Client menu: Figure 5–4. DNS Client Menu...

  • Page 126: Configuring Dhcp Client

    Displaying the DNS Cache and Statistics To display information about the data in the DNS cache, type S. When DNS Client is enabled, the IAD displays the following information: IP Address 392 Total Requests 117 Requests Serviced From Cache 295 Requests Sent to Server 2 Server Timeouts 293 Server Good Responses 3 Server Not Found Responses...

  • Page 127: Configuring Dhcp Relay

    Configur- DHCP Relay allows the IAD to forward DHCP requests from the LAN to a separate DHCP Server. To configure the IAD for DHCP Relay, type L on ing DHCP the Router Configuration menu. The IAD displays the DHCP Relay menu, Relay which contains commands to configure DHCP Relay: Figure 5–5.

  • Page 128: Configuring The Telnet Server Port

    5. Reset the IAD (page 14) when you finish router configuration. Displaying DHCP Relay Statistics To display information about DHCP Relay, type S on the DHCP Relay menu. When DHCP Relay is enabled, the IAD displays this report: 215 Client requests forwarded to DHCP server 1 Client requests dropped 190 Server responses forwarded to DHCP clients 0 Server responses dropped...
  • Page 129 Figure 5–6. IP Filtering Configuration Menu ******************************************* ******************************************* Editing Unselected Port Input filters P. Choose port for IP filtering F. Globally enable/disable input or output filters T. Toggle input or output type filters to view/edit D. Display all filters of the chosen type I.
  • Page 130 5. Continue with other configuration tasks, or press Escape to return to the Main menu. 6. Reset the IAD (page 14) when you finish IP filtering configuration. Globally Enabling and Disabling Filters Use these commands to enable and disable the input and output filters for all installed interfaces.
  • Page 131 Inserting, Appending and Editing Filters To edit an existing filter, add a new filter in a specific location in the filter table or append a filter to the bottom of the table, follow these steps: NOTE 1. Use the Toggle command (option T) to select input or output filters. Next, choose one of the following and proceed to step 2: A.
  • Page 132 Copying Filters for Editing To copy and edit filters, first toggle input or output filters (option T), then type C on the IP Filtering Configuration menu to display the IP Filter Copy to Buffer menu (2-F-C): Figure 5–7. IP Filtering Copy to Buffer Menu ***************************************** ***************************************** C.
  • Page 133 When you’re done viewing the details, press any key to return to the IP Filter Copy to Buffer menu. Table 5–2. Filter Details Parameter state action srcLwP srcHiP source.ip.addr.low source.ip.addr.high proto mask dstLwP dstHiP dest.ip.addr.low dest.ip.addr.high Editing a Filter in the Buffer To edit a filter currently stored in the buffer, follow these steps: 1.
  • Page 134 Deleting an IP Filter To delete a filter from the IP Filter table, toggle input or output filters (Option T on the IP Filtering Configuration menu) and follow these steps: 1. On the IP Filtering Configuration menu, type X to select Delete one filter of the chosen type.

  • Page 135: Configuring Ip Header Compression (Iphc)

    Configur- IPHC reduces the number of bytes transmitted across the WAN, thus conserving bandwidth. ing IP To enable or disable IP header compression, follow these steps: Header 1. On the Router Configuration menu, type Q. Compres- 2. The IAD displays the port table and prompts for a port: sion (IPHC) Port VPI VCI Encapsulation Type Maximum PCR this interface can support = 3622 cps...
  • Page 136 Network AddressNetmask 98.1.1.5 255.255.255.0 98.1.1.6 255.255.255.0 99.9.9.1 255.255.255.0 91.1.1.18 255.255.255.255 91.1.1.1 127.0.0.1 255.0.0.0 Route Table parameters are described in the following table. Table 5–3. Route Table Parameters Parameter Network Address Netmask Gateway Address Interface Metric Type 2000-A2-GB20-10 Gateway Address Interface Metric Type 91.1.1.1 99.1.1.1 100.9.9.9...
  • Page 137 This chapter describes how to configure the IAD as a bridge. A bridge is a device that connects and passes packets between two network segments that use the same communications protocol. A router generally improves overall efficiency for a complex network, but a bridge provides better speed and flexibility for the overall network.

  • Page 138: Basic Bridge Setup Tasks

    Basic Although the IAD is pre-configured with bridging enabled, you should perform these tasks for your network: Bridge ‹ Enable bridging globally (page 121) or by port (page 121) Setup ‹ Set the bridge aging timer (page 122) Tasks ‹ Disable RIP poisoned reverse globally (page 101) or by port (page 101) ‹...

  • Page 139: Bridge Configuration Menu

    Bridge Configuring the IAD as a bridge involves several tasks. These are all displayed and accessed on the Bridge Configuration menu (displayed by Configura- typing 3 on the Main menu). Each task in this chapter is described tion Menu beginning at the Bridge Configuration menu. Figure 6–2.

  • Page 140: Enabling Or Disabling Bridging Globally

    To implement IP Over Bridging, enable bridging globally, and by port on the WAN connection. (At least one DLCI/PVC must be configured), and assign an IP address to the WAN interface. When these conditions exist (either in Routing or Bridging configuration), the IAD will prompt you to enable or disable IP Over Bridging.

  • Page 141: Setting The Bridge Aging Timer

    Type the number of the port for which you want to enable bridging. 3. If more than one interface is configured on the selected port, the IAD displays a list of interfaces: Port Type the number of the port. 4. The IAD displays the status of bridging on this interface and port, and a prompt: Bridging over T1/E1 Port 1, is currently DISABLED Enter E to Enable, D to Disable:...

  • Page 142: Enabling And Disabling Stp

    Enabling Having many bridges creates the potential for network loops. A loop presents conflicting information about the segment on which a specific and Dis- address is located and forces the bridge to forward all data. abling STP When configuring the IAD as a router (Chapter 4, page 96), you must disable STP both globally and by port.

  • Page 143: Configuring Spanning Tree Bridge Priority

    Configur- The Spanning Tree algorithm selects the bridge with the lowest priority on the network as the Root Bridge. ing Span- To set the Spanning Tree bridge priority (a value between 1 and 65,565— ning Tree default 32,768), follow these steps: Bridge Pri- 1.

  • Page 144: Configuring Spanning Tree Hello Time

    Configur- To set the Spanning Tree hello time (a value between 1 and 10 seconds— default 2), follow these steps: ing Span- 1. Type H on the Bridge Configuration menu to select Configure Spanning ning Tree Tree Hello Time. Hello Time 2.

  • Page 145: Deleting A Bridge Forwarding Database Entry

    Available Interfaces: 1. G2237 xDSL 2. 10/100BaseT Ethernet 0. (Abort) Type the number of the port to update. 3. If more than one interface is configured on the selected port, the IAD displays a list of interfaces: Port Type the number of the port. 4.

  • Page 146: Basic Voice Path Setup Tasks

    After you have defined the voice PVCs or DLCIs on the IAD, you should configure the voice path for voice operation to function correctly. This chapter contains the following topics: ‹ Basic Voice Path Setup Tasks (page 127) ‹ Voice Path Configuration Menu (page 127) ‹...

  • Page 147: Voice Path Configuration Menu

    Voice Path Configuring the voice path settings involves several tasks. These are all displayed and accessed on the Voice Configuration menu (displayed by Configura- typing P on the Main menu). tion Menu Tasks in this chapter are described beginning at the Voice Configuration menu.
  • Page 148 Figure 7–2. Voice Configuration Menu (POTS Telephone Interface) ******************************************* ******************************************* Current Voice Gateway is MGCP 1.0 0. No Voice Gateway 1. MGCP 0.1/NCS 1.0 2. CopperCom 3. Jetstream 4. AAL2/LES CAS 5. AAL2/LES ELCP 6. MGCP 1.0 JF2004i, JF2104i POWER LAN LINK LAN ACT WAN LINK...

  • Page 149: Setting Jitter Delay

    Setting Jit- Inter-arrival jitter is the difference in relative transit time for two packets. It is the difference between the packet’s RTP time-stamp and the receiver’s ter Delay clock at the time of arrival of the packet. As shown in the equation below, this is equivalent to the difference in the relative transit time for two packets: the relative transit time is the difference between a packet’s RTP time-stamp and the receivers clock at the time of arrival, measured in the same units.
  • Page 150 Type the option for the task to perform. Proceed to the appropriate section. Setting All Ports to Loop Start 1. Type 1 to select Set All Ports to Loop Start. 2. The IAD sets all ports to Loop Start and saves the configuration. 3.

  • Page 151: Setting Slic Control Mode

    Setting To set SLIC control mode (for POTS only), type T to display the SLIC Control Mode Selection menu: SLIC Con- trol Mode Figure 7–5. SLIC Control Mode Selection Menu ******************************************* ******************************************* Current Control Mode = AUTO Control Mode A. AUTO Control Mode B.

  • Page 152: Set On Hook Transmission Mode

    Set On To set On-hook Transmission mode (POTS only) for groundstart lines, type O to display the Ground Start OHT Mode Selection menu: Hook Transmis- Figure 7–7. Ground Start OHT Mode Selection Menu sion Mode ******************************************* ******************************************* On Hook Transmission for a Ground Start Line is DISABLED.

  • Page 153: Setting Debug Mode

    Reset the IAD Reset the IAD (page 14) when you finish voice path configuration. Setting Option M, Set Debug Mode, is reserved for Paradyne network engineers. Debug Mode Configur- To set echo cancellation default settings, type E to display the Echo...

  • Page 154: Setting Loop Gain

    Press any key to return to the Echo Cancellation Default Settings Configuration menu. Enabling and DIsabling Echo Cancellation for all Ports 1. Type 3 to enable or disable echo cancellation for a specific port. 2. The IAD displays the port prompt: Select Line: [1-8] Type the port number to set.
  • Page 155 1. Type 1 to select Set Loop Gain for all ports. 2. The IAD displays this prompt for the transmit loop: Enter Transmit Loop Gain for all ports (range -9dB/ 3dB) [-2dB]: Type the value (include a dash for negative values) and press Enter. 3.

  • Page 156: Setting Country Mode

    Displaying Loop Gain Settings To display information about Loop Gain settings, type 2. The IAD displays the loop gain values for each telephone port on the IAD (sample shown): Port Press any key to return to the menu. Press Escape to return to the Voice Configuration menu and continue with other voice path configuration.

  • Page 157: Managing Mgcp Embedded Client

    When you select a specific country mode, the values are set automatically: JF2008 JF2104 POWER LAN LINK LAN ACT WAN LINK VOICE JF2108 Figure 7–11. Country Mode Selection Menu ******************************************* ******************************************* Current Country Name is ETSI Generic Current Country Mode is Europe A.
  • Page 158 Figure 7–12. MGCP/NCS Management Menu ******************************************* ******************************************* C. Configure MGCP parameters S. Display MGCP statistics D. Debug MGCP R. Remove a connection A. Port Administration P. Configure Default Packet Size Type the option for the task to perform and proceed to the appropriate section.
  • Page 159 Configuration Invalid, initialization incomplete. Debugging MGCP The commands displayed on the Debug MGCP menu are reserved for Paradyne network engineers. Removing a Connection Type R to remove a lost connection. Type the number of the Connection ID to delete and press Enter.
  • Page 160 Setting Admin State Globally 1. Type 1 to enable or disable the admin state for all ports. 2. The IAD displays this prompt: Enter E to Enable, D to Disable: Type E to enable the admin state, or D to disable it. 3.

  • Page 161: Managing Copper-Com Call Control

    Managing When your IAD is configured for connection to a Coppercom Voice Gateway (option V on the VoicePath Configuration menu—P-V), type E on Copper- the Main menu to display the CopperCom Call Control menu: Com Call Figure 7–14. CopperCom Call Control Menu Control ******************************************* *******************************************...
  • Page 162 Figure 7–16. CopperCom Configuration Menu ******************************************* ******************************************* D. Display Configuration C. Compression Format F. Framing Format Type the option for the command to execute and proceed to the appropriate section. Displaying CopperCom Configuration Type D to display the current configuration settings. The IAD displays the following information: Configuration: Current Frame Relay Mode = 44 octets &...

  • Page 163: Jetstream Call Control Settings

    The commands in the CopperCom Debug Control menu are reserved for use by Paradyne or CopperCom network engineers. JetStream When you have specified the JetStream (Paradyne) Voice Gateway, type E to display the Call Control Settings menu for JetStream: Call Con- trol Set- Figure 7–18.
  • Page 164 Port 08 is offhook Call Control state = Idle POTS state = Disabled Received Segmentation Layer CRC failures since powerup = 0 Configuring Trace Settings These commands are reserved for use by Paradyne network engineers. 2000-A2-GB20-10 - 145 - February 2004...

  • Page 165: Configuring Aal2/Les Cas

    Selecting Insufficient Bandwidth Sound Type V to select the type of dial tone heard by the telephone user if there is insufficient WAN bandwidth to complete a call. The IAD displays the Insufficient Bandwidth Indication Setting menu and the current setting: Figure 7–20.
  • Page 166 Figure 7–22. AAL2/LES Configuration Menu ************************************ ************************************ AAL2/LES is MANUALLY configured. Port Control (bit mapping) is 0x00000000 CAS signaling is GR303-ABCD. CAS refreshing is DISABLED. Idle CAS refreshing is DISABLED. Max. CPS-SDU size is 0 octets. "Combined use" timer is 0 millisecond(s). User state control (USC) is DISABLED.
  • Page 167 1. Type P to enable and disable ports. 2. The IAD displays the port control prompt: Port Control x(10011001): Enter a zero (0) in each port location to disable the port; enter a 1 in each port location to enable the port. Press Enter to complete the step. 3.
  • Page 168 4. You must reset the IAD (page 14) before this change takes effect. Debugging AAL2/LES Gateways NOTE Displaying AAL2/LES Statistics Type S to display the AAL2/LES Statistics menu: 2000-A2-GB20-10 The commands in option D, Debug Control, are reserved for use by Paradyne network engineers only. - 149 - February 2004...

  • Page 169: Configuring Aal2/Les Ccs-Elcp

    Figure 7–25. AAL2/LES Statistics Menu ************************************ AAL2/LES Statistics ************************************ D. Display Audio/CAS/Alarm Statistics C. Clear Statistics Type the option for the command to execute and proceed to the appropriate section. Displaying Audio/CAS/Alarm Statistics Type D to display transmitted and received audio, CAS, dropped, and alarm statistics by line.
  • Page 170 Setting Debugging Options Type D to display debugging information for AAL2/LES CCS-ELCP, and set debugging options. 2000-A2-GB20-10 Configuration Use of commands in the Variant/Interface Management menu is reserved for use by Paradyne network engineers only. Debugging - 151 - February 2004...
  • Page 171 ******************************************* ******************************************* D. Display AAL2 Channel Statistics C. Clear AAL2 Channel Statistics 2000-A2-GB20-10 The use of these debugging options is reserved for Paradyne network engineers only. Enabling debug options may significantly affect IAD performance. Signaling Port Control AAL2 Channel Statistics...
  • Page 172 Displaying AAL2 Channel Statistics Type D to display the AAL2 channel statistics: <<< Audio and Alarm Statistics >>> ---------- Tx ------------------ Rx ---------- Audio Alarm Dropped Audio Alarm Dropped <<< Frame Mode Data Statistics >>> --- ---- Tx ---- ---------------- Rx ----------------- CID Frame Dropped Frame Dropped RasTO BadCrc TooLong Press Escape to return to the menu.

  • Page 173: Firewall Configuration

    Creating a Firewall configuration (also known as IP filtering) allows you to specify a combination of parameters the IAD uses to selectively eliminate IP traffic. Firewall via Filtering executes on the WAN port that you select. There are two different IP Filtering sets of filters and each filter maintains its own statistics: ‹...

  • Page 174: Basic Dhcp Server Setup Tasks

    This chapter describes the tasks required to configure the Dynamic Host Configuration Protocol (DHCP) server on the LAN connection. DHCP allows for dynamic allocation of network addresses and configurations to newly attached hosts. DHCP reduces the work required to administer a large network. This chapter contains the following topics: ‹...

  • Page 175: The Dhcp Server Configur-Ation Menu

    DHCP Server. Options that display in the DHCP Server Configuration menu are the same for both security levels. NOTE Using The commands in option B, Enable/Disable DHCP Debug Messages, are reserved for use by Paradyne network engineers. DHCP Debugging Messages Enabling...

  • Page 176: Configuring Dhcp Server Parameters

    3. If DHCP Relay is not enabled, the IAD displays this prompt: DHCP Server is currently DISABLED Enter E to Enable, D to Disable: Type E to enable DHCP Server, to type D to disable DHCP Server. Proceed to Step 1 in the next section. Enabling When the IAD boots, the internal DHCP server may be configured to check for additional DHCP servers on the LAN, and disable IAD-based...

  • Page 177: Configuring The Dhcp Address Range Pool

    7. The IAD displays the current lease time and prompt: Current Lease time is 3600 seconds Enter DHCP Lease Time in seconds > Type the new lease time value in seconds, and press Enter. 8. The IAD displays the NetBIOS Type Configuration menu: Current NetBIOS Node Type: h-node 1.
  • Page 178 4. The IAD displays an update option. Respond Y to override the lease time default for this entry: Enter Y to enter a value for Lease Time Enter N to use a default value Enter Lease Time in seconds for this Client (3600): Type the lease time for this entry and press Enter.

  • Page 179: Displaying Dhcp Server Details

    ******************************************* Current NetBIOS Node Type: Default 1. B-node 2. P-node 4. M-node 8. H-node Type the default NetBIOS node type for this entry and press Enter. 11. The IAD saves the configuration. 12. Reset the IAD (page 14) for changes to take effect. Displaying 13.

  • Page 180: Displaying Dhcp Server Statistics

    When you’re done viewing the information, press any key to return to the menu. Displaying Type S to display DHCP Server statistics. The IAD displays the following information about the DHCP Server. DHCP Server Sta- Table 9–2. DHCP Server Statistics tistics Statistics plain bootp requests received...

  • Page 181: Displaying Dhcp Entry Details

    Displaying Type D to display DHCP entry details. The IAD displays the following information about the DHCP entries: DHCP Entry Table 9–4. DHCP Entry Details Details Value IP address Client ID Status Subnet Gateway Lease Type Name For the IAD to display this information, you must attach DHCP Client devices that use DHCP to obtain an IP address from the IAD.

  • Page 182: Configuring Multicast

    Multicast (point-to-multipoint) is a communication feature that allows a source host to send a message to a group of destination hosts. Multicasting reduces traffic on the local network by sending only one (multicast) packet out to a higher-bandwidth relay point. Multicasting differs from broadcasting in that a receiver must join a multicast group in order to receive group messages.

  • Page 183: Enabling And Disabling Global Ip Multicast

    The Multicast Configuration menu contains commands to configure IP Multicast Routing. The IAD only displays the Multicast Configuration menu when DHCP Server is enabled, and the IAD has been reset. When you have completed multicast configuration, reset the IAD for the changes to take effect.

  • Page 184: Managing Multicast Route Source

    Managing Reverse Path Forwarding (RPF) checks the IP address of the sender of the packet and then finds the best outgoing interface from its normal IP Multicast routing table. Route Type S to add or change the Multicast Route Source. The IAD displays the Source Multicast Routing Source menu: Figure 10–2.

  • Page 185: Removing A Multicast Routing Source

    Removing Type R to remove a Multicast Routing Source: a Multicast 1. The IAD displays the IP address prompt: Routing Enter IP address for the Source: Type the source IP address and press Enter. Source 2. The IAD displays the current subnet mask and prompt: Enter subnet mask for the source: (255.255.255.0) ->...

  • Page 186: Displaying The Igmp Querier

    224.0.0.2 (Default Local Join) Expires: NEVER 224.0.0.13 (Default Local Join) Expires: NEVER Press any key to continue. Displaying The IGMP Querier is the IGMP router that has the highest IP address among the others. It sends periodic IGMP Query messages and handles the IGMP IGMP Membership Report and Leave messages.

  • Page 187: Displaying The Pim Neighbor

    Table 10–1.Multicast Routing Table Fields Field Static Mroute Incoming interface RPF Neighbor Outgoing Interfaces Pruned Since Multicast packets are forwarded according to the preceding information, this table is the key for IP Multicasting. Displaying Type N to on the Multicast Configuration menu to show the PIM Neighbor. The IAD displays the neighbor for each interface and its expiration times.
  • Page 188 This chapter describes the steps required to configure Network Address Translation (NAT). NAT multiplexes traffic from the internal network and presents it to the Internet as if it is from a single source that has only one IP address. The NAT Local Server may be configured with a range of both TCP and UDP ports, which benefits applications including video conferencing and multi-user games.

  • Page 189: The Nat Configuration Menu

    If you sign on as Network Manager, option B (Enable/Disable NAT Debug Messages) is not displayed. This option is reserved for Paradyne network engineers. Be sure to reset the IAD when you are done making changes to NAT configuration. Resetting the IAD causes the configuration changes to take effect.

  • Page 190: Enabling Nat Translation

    A significant advantage of NAT is that you can configure it without changing hosts or routers, other than those few routers on which NAT is configured. NAT multiplexes internal network traffic and presents it to the Internet as if it is from a single source with one IP address. To configure NAT, complete the following steps: ‹...

  • Page 191: Configuring Nat Local Server

    Configuring To configure the NAT local server entry, follow these steps: NAT Local 1. Type N on the NAT Configuration menu to select Configure NAT Local Server Entry. Server 2. The IAD displays the following: Enter NAT Local Server Entry to Configure (1..10:(1) Type the number of the local server entry and press Enter.

  • Page 192: Configuring Nat Timeouts

    Updating NAT Local Server entry 1, Translated IP address 91.1.1.200 Translated Port 32 is accessible as Standard Port 32 Translated Port 33 is accessible as Standard Port 33 Translated Port 34 is accessible as Standard Port 34 Translated Port 35 is accessible as Standard Port 35 11.

  • Page 193: Configuring The Nat Port Range

    Configuring The size of the NAT port range defines the number of simultaneous connections permitted. A small port range limits the number of the NAT connections. Since the range that you assign must be outside the range of Port Range assigned ports, do not set port ranges under 5,000.

  • Page 194: Configuring The Nat Alias Entry

    Configuring Each NAT alias entry allows a device on the LAN (inside of NAT) to be accessible from the Internet via a unique IP address. The IAD only the NAT translates IP addresses for alias entries—port numbers are not changed. Alias Entry You can create up to 7 direct public-to-private IP address mappings via the NAT alias table.

  • Page 195: Nat Statistics

    When NAT is enabled, you can review statistics gathered as NAT operates. To display NAT statistics, type S on the NAT Configuration menu. Statistics The IAD displays the following information (sample): timeouts: TCP: 300, UDP: 120 local to inet: pkts:0, bytes:0 inet to local: pkts:0, bytes:0 Connections: TCP 0, UDP:0, ICMP:0 created: 0, deleted 0 Total Fragments: local to inet: 0, inet to local: 0...

  • Page 196: Nat Connection Table

    When NAT is enabled, you can display the current open connections. To display the connection table, type C on the NAT Configuration menu. Connection The IAD displays the NAT connection table (sample): Table TCP: 11.22.13.152:23 <-> 192.168.1.1:4428 out_port:50000, pkts; out 13, in 13 state:4 idle:13 If there are no open connections, the IAD advises you.
  • Page 197 If the connection is not open, the IAD advises you. Press any key to return to the NAT Configuration menu. Table 11–4.NAT Connection Details Report Entry Foreign IP Local IP Outside port Inside port Foreign port Outgoing packets/# bytes Incoming packets/# bytes Type Seconds since use TCP/UDP Sequence...

  • Page 198: Nat Local Server Table

    NAT Local When NAT is enabled, you can display the entries in the local server table. To display the table, type O on the NAT Configuration menu. Server Entry Local IP Address Local Port Internet Port Protocol Table Press any key to return to the NAT Configuration menu. Table 11–5.NAT Local Server Table Report Report Entry Entry...

  • Page 199: Deleting A Nat Local Server Entry

    Deleting a To delete a local server entry: NAT Local 1. Type Y on the NAT Configuration menu. 2. The IAD prompts for the entry number to delete. Server Enter NAT Local Server Entry to Delete (1..20): (1) Entry Type the number of the table entry and press Enter. 3.

  • Page 200: The Report Menu

    This chapter describes the report subsystem in the IAD. The report subsystem allows you to display information about the current configuration of the IAD, and collect, display and clear statistics on various network and media interfaces. You can also display reports about routing and bridging, and other reports about the operation of the IAD.

  • Page 201: Current Configur-Ation Report

    Most options on the Reports menu generate a specific report. However, the Network Statistics, Interface Statistics and Media Statistics options display a menu of several related reports and commands to reset accumulated statistics. To display a report or group of reports, or to clear statistics for a particular protocol or interface, select the option and proceed to the appropriate section.
  • Page 202 Table 12–1. Current Configuration Report Parameter Telnet Server Port DNS Server IP Address DNS Server Timeout Application Information Support File Information Interface type Admin state Physical state WAN DataLink Protocol xDSL type Firmware Version ADSL Standard for Startup SDSL Mode Mode Line Rate Payload Scrambling...

  • Page 203: Network Statistics Reports

    Table 12–1. Current Configuration Report Parameter HDB3 coding Payload Scrambling Port # Sa4 Bit Sa5 Bit Sa6 Bit Sa7 Bit Sa8 Bit Rcv Clk Source PPP Auth Type (WAN port) Userid Password Peer Name DLCI—Frame Relay Only VPI/VCI—ATM Only IP Interfaces on Port # IPAddr IPMask Priority...
  • Page 204 Figure 12–2. Network Statistics Menu C. Display ICMP Statistics G. Display IGMP Statistics I. Display IP Statistics P. Display PIM Statistics T. Display TCP Statistics U. Display UDP Statistics Z. Clear a Network Statistic To display a specific report, enter the option. For detailed information about each report in the Network Statistics menu, or to clear network statistics, proceed to the appropriate section: ‹...
  • Page 205 Table 12–2. ICMP Statistics Report Parameter discarded due to internal errors with illegal type or code Messages, Requests, and Replies Received Destination Unreachables received Time Exceededs received Parameter Problems received Source Quenches received No. of ICMP Source Quench message received. Redirects received Echo Requests received Echo Replies received...
  • Page 206 Group Message Protocol) received packets, sent packets, and queries, reports, and messages sent and received. Table 12–3. IGMP Statistics Report Parameter Received Packet Information packets received discarded for lack of resources discarded due to internal errors discarded for other reasons: - unrecognized codes - bad checksums - packets smaller than...
  • Page 207 Table 12–3. IGMP Statistics Report Parameter Ver. 2 Membership Report sent Leave-group message sent DVMRP routing message sent PIM routing message sent No. of IGMP PIM routing messages sent. Traceroute resp sent Mcast traceroute messages sent Other messages sent IP Statistics Report To display the IP Statistics report, type I on the Network Statistics menu.
  • Page 208 Table 12–4. IP Statistics Report Parameter - with zero TTL fragments received fragmented packets reassembled fragments discarded Sent Packet Information packets sent discarded for lack of resources discarded due to internal errors destinations found unreachable fragments sent packets fragmented fragmentation failures PIM Statistics Report To display the PIM Statistics report, type P on the Network Statistics menu.
  • Page 209 Table 12–5. PIM Statistics Report Parameter Received Messages Information Hello received Register received Register Stop received Join/Prune received Bootstrap received Assert received Graft received Graft Ack received Cand RP Adv received other messages received Sent Messages Information Hello sent Register sent Register Stop sent Join/Prune sent Boosters sent...
  • Page 210 Table 12–6. TCP Statistics Report Parameter - bad checksums - with headers too small - packets smaller than header - packets larger than frame Packet is larger than the internal packet buffer. - acks for unsent data - with data outside window The remote host has sent data beyond the window - with data after close segments with data segments with duplicate...
  • Page 211 Table 12–6. TCP Statistics Report Parameter connections gracefully closed connections aborted failed connection attempts Not used UDP Statistics Report To display the UDP Statistics report, type U on the Network Statistics menu. The UDP Statistics report displays detailed information about UDP (User Datagram Protocol) packets sent and received.

  • Page 212: Interface Statistics Reports

    Figure 12–3. Clear Network Statistics Menu C. Clear ICMP Statistics G. Clear IGMP Statistics I. Clear IP Statistics P. Clear PIM Statistics T. Clear TCP Statistics U. Clear UDP Statistics To permanently reset statistics for a specific protocol, type the option. The IAD immediately resets all statistics for the specified protocol, and displays the menu.
  • Page 213 For detailed information about each report in the Network Statistics menu, or to clear network statistics, proceed to the appropriate section: ‹ ARP Statistics Report ‹ Interface Statistics Report ‹ Bridge Statistics Report ‹ DLCI Statistics Report ‹ ATM PVC Statistics Report ‹...
  • Page 214 Table 12–8. ARP Statistics Report Parameter valid replies rcvd requests sent replies sent ARP_alloc returned NULL cache misses discarded, missing ARP entry Interface Statistics Report To display the Interface Statistics report, type I on the Interface Statistics menu. The Interface Statistics report provides details about all packets sent and received on the selected interface.
  • Page 215 Table 12–9. Interface Statistics Report Parameter unicast sent multicast sent broadcast sent 2000-A2-GB20-10 Description No. of Unicast Packets sent from interface No. of Multicast Packets sent from interface No. of Broadcast Packets sent from interface - 196 - February 2004...
  • Page 216 Bridge Statistics Report To display the Bridge Statistics report, type B on the Interface Statistics menu. This report provides details about all packets sent and received on the IAD bridge. Table 12–10.Bridge Statistics Report Parameter Received Packet Information bridge packets received bridge octects received discarded for lack of resources...
  • Page 217 Table 12–11.DLCI Statistics Parameter Committed Burst Excess Burst Throughput Rx Frames Received Frame Information Rx Bytes Rx Discarded Frames Rx RECN Rx BECN Rx DE Rx Excess Rate Rx Committed Rate Transmitted Frame Information Tx Frames Tx Bytes Tx Discarded Frame Tx FECN Tx BECN Tx DE...
  • Page 218 ATM PVC Statistics Report To display the PVC Statistics Reports, type A on the Interface Statistics menu. This option is only displayed when ATM is selected as the data link protocol. Several associated reports are available, depending on the specification of the PVC: ‹...
  • Page 219 AAL2 Statistics Report This PVC Report displays when an AAL2/LES PVC is configured. Table 12–13.Common CPCS-2 Statistics Report Parameter Transmit overflows Receive STF parity errors Receive sequence errors Bad rx OSF sequence errors Bad OSF value errors Receive HEC errors Receive overlap HEC errors Receive CID errors...
  • Page 220 Cumulative CPCS-2 Statistics Report Table 12–14.Cumulative CPCS-2 Statistics Report Parameter Maximum PDU Size Transmit bytes counter Transmit microcell counter Total AAL2 Cells sent. Tx discarded microcells errors Tx too long microcell errors Length of transmitting cells is larger than PDU size. Tx reserved UUI errors Receive bytes counter Receive microcell counter...
  • Page 221 Table 12–15.Common AAL Statistics Report Parameter Max PDU Rx Frames Rx Cells Rx Bytes Rx Error Cells Rx Error Frames Tx Frames Tx Cells Tx Bytes Tx Discarded Tx OverFlow Tx UnderFlow Tx Inactive Rx Inactive CRC 32 Errors The size Reassembly Timeouts Frames too Long 2000-A2-GB20-10...
  • Page 222 IP Header Compression Statistics Report This report is available when ATM PVC Encapsulation Type RFC 1483 is selected, an IP address is assigned and IP Header Compression is enabled on the ATM Interface. Table 12–16.IP Header Compression Statistics Report Parameter Missed TCP contexts Missed RTP context Sent Packet Information...
  • Page 223 PPP Statistics Report This report is available when ATM PVC Encapsulation Type RFC 2364 is selected. Table 12–17.PPP Statistics Report Parameter Received Packet Information packets received discarded for various reasons LCP rejects - echoes - replies - discards Sent Packet Information packets sent discarded (link not open) LCP rejects...

  • Page 224: Media Statistics Reports

    Media Sta- Type M on the Reports menu to display Media statistics reports. tistics Media statistics reports display statistical information about the total packets handled (Layer 2) on a per port basis. Reports Reports on physical connections vary, based on the type of connection. Reports include Ethernet, USI, G.SHDSL, ASDL, SDSL, ATM and Frame Relay.
  • Page 225 Frame Relay Statistics Report Type F to display the Frame Relay Statistics report. This report displays basic about Frame Relay operations on the WAN link (for all ports and DLCIs). Table 12–18.Frame Relay Statistics Report Parameter Received Data Rx Frames Rx Bytes Rx Frames discarded DE set on Rx...
  • Page 226 Table 12–18.Frame Relay Statistics Report Parameter Tx congestion counter CLLM frames Tx LMI frames Tx ANSI frames Tx Last error: Serial (USI) Statistics Report Type S to display the Serial Statistics report. This report displays basic serial (HDLC) transport statistics on the Universal Serial Interlace port. Table 12–19.Serial Statistics Report Parameter bytes rcvd...
  • Page 227 Table 12–19.Serial Statistics Report Parameter bytes sent packets sent discarded, TX ring full discarded, bad pkt or link not ready discarded, TX error Tx Clk glitch Tx underrun CTS lost ATM Statistics Report This report displays basic ATM transport statistics at the cell level for all ports and PVCs.
  • Page 228 Table 12–20.ATM Statistics Report Field EFCI Tx RM Tx Rx HEC Errors Lost Cell Delineation (OCD) Time in OCD ATM Sync 2000-A2-GB20-10 Description No. of cells transmitted with EFCI (Explicit Forward Congestion Indication) bit is on. No. of RM (Resource Management) cells transmitted.
  • Page 229 G2237 xDSL Statistics Report Table 12–21.G2237 xDSL Statistics Report Parameter Operational State Start Progress Operational Seconds Up/Down Counter Received SNR Mean SQ Error Initial Received SNR Loop Attenuation Actual PSD Mask Framer Sync LOSW Status Total Seconds Errored Seconds CRC Count LOSW Defect Count FEBE Count Tip/Ring...
  • Page 230 Table 12–21.G2237 xDSL Statistics Report Parameter Remote HDSL2 Version Remote Country Code Provider Code Remote Vendor Data Low Remote Vendor Data Hi Data Mode Heartbeat Framer Sync Lost Tick 2000-A2-GB20-10 Description Current version of the Remote HDSL2. Current Remote Country Code. Current Provider Code.
  • Page 231 Ethernet Statistics Report Table 12–22.Ethernet Statistics Report Parameter Received Packet Information packets rcvd discarded, RX ring empty discarded, unrecognized protocol discarded, RX error alignment errors bad fcs runt giant late collision overrun Sent Packet Information packets sent discarded, TX ring full discarded, bad pkt discarded, TX error heartbeat lost...
  • Page 232 Table 12–22.Ethernet Statistics Report Parameter Description carrier sense lost No. of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.
  • Page 233 G7070 ADSL Statistics Report Table 12–23.G7070 ADSL Statistics Report Parameter Operational Seconds Downstream SNR Margin Downstream Attenuation Upstream Attenuation Near-End FEC (i) Near-End CRC (i) Near-End SEF Near-End LOS Far-End FEC (f) Far-End CRC (f) Far-End SEF Far-End LOS Near-End CRC Last Near-End CRC Last Failure Counters Overall...
  • Page 234 POTS Statistics Report Table 12–24.POTS Statistics Report Parameter Line X Active/Inactive Buffers Rcvd Buffers Sent Discarded Underrun 2000-A2-GB20-10 Description Current status of line X. Active: Phone line connection is up. Inactive: Phone line connection is down. No. of packets received from this POTS line. No.
  • Page 235 BRI Statistics Report Table 12–25.BRI Statistics Report Parameter D Channel Active/Inactive Frames Rcvd Frames Sent Rx Overflow (RFO) Rx Invalid Frames Rx Overflow (RDO) Rx CRC Errors Rx Aborted Tx Underrun Tx Collision B Channel Buffers Rcvd Buffers Sent Discarded Underrun Clearing Media Statistics To clear network statistics, type Z on the Network Statistics menu.

  • Page 236: Route Table Report

    Route Table Type R to display the Route Table report in the Reports menu. The IAD lists each route by IP address, and displays the following information about Report statically configured routes and dynamically learned ones. Table 12–26.Route Table Report Parameter Network Address Netmask...

  • Page 237: Bridge Status Report

    Table 12–28.Bridge Forwarding Database Report Parameter Port Timer You must enable bridging for this table to display. For more information on enabling bridging, see Bridge Sta- To display information about bridging, type S on the Reports Menu. The IAD displays a record for each interface: tus Report Table 12–29.Bridge Status Report Parameter...

  • Page 238: System Uptime Report

    Otherwise, the following information is displayed for each entry: Table 12–30.PPP Authorization Report Parameter Authorization type Slot #/Interface #/Port # Userid/Password/Peer Name Press any key to return to the Reports menu. System Type U on the Reports menu to display the amount of time elapsed since the IAD was reset: Uptime The system has been running for 11 hours,...

  • Page 239: Zero All Statistics

    Kernel Free Memory Free Blocks Largest Free Block Size Reserved Area Size When you are done reviewing the report, press any key to return to the System Memory Report menu. Kernel Tasks Memory Statistics Report Type T on the Memory Statistics menu to display the Kernel Tasks Memory Statistics report.

  • Page 240: Intro-Duction

    Intro- The command line interface is often more convenient to use than the menu interface. Many of the tasks you normally perform using the menu duction interface are also available in the command line interface. To enter command line interface (CLI) mode, type C on the Main menu. The IAD enters command mode, and allows you to enter IAD commands (described below) until you type the exit or quit command to return to the menu interface.
  • Page 241 on | off Keywords to enable (on) or disable (off) STP. slot Numeric value identifying the connection (0-3) interface Always 0 Discussion. This optional section contains detailed descriptions, examples if necessary, and any limits, exceptions, or warnings you should be aware of when using this command. 2000-A2-GB20-10 - 222 - February 2004...

  • Page 242: Command Line Interface Reference

    Command Each command in the command line interface is described below, in alphabetic order. Line Interface Reference exit Description. Quits the command line interface and returns to the menu system. exit ping Description. Pings an IP address. The IP address must be on the same subnet.

  • Page 243: Reset System

    reset Description. Performs a soft system reset. system reset system Discussion. Any time you use the menu or command line interface to make setting changes, or change any of the physical characteristics of the IAD (such as changing the MAC address of the Ethernet port), you must reset (or restart) the IAD for the new settings to take effect.

  • Page 244: Set Bridge Stp Global

    set bridge Description. Enables or disables Spanning Tree Protocol globally. stp global set bridge stp global <on | off> on | off Keyword to enable (on) or disable (off) STP globally. set dhcp Description. Enables or disables DHCP server on the IAD. server set dhcp server enable <on | off>...

  • Page 245: Set Dhcp Server Range

    set dhcp Description. Sets the DHCP server low and high IP address range. server set dhcp server range <low IP address> <high IP address> range Low IP address IP address in octal format (999.999.999.999) High IP address IP address in octal format (999.999.999.999) set dns Description.

  • Page 246: Set Lan Bridge

    set lan Description. Enables or disables bridging on a LAN port. bridge set lan bridge <on | off> (slot) (interface) (port) on | off Keyword to enable (on) or disable (off) bridging on the specified port. IP address IP address in octal format (999.999.999.999) netmask Subnet mask in octal format (255.255.255.255) slot...

  • Page 247: Set Lan Rip

    set lan rip Description. Enables or disables RIP on a WAN IP port If you do not enter any optional parameters, the IAD performs the command against the first available slot, interface and port. set lan rip <on | off> <version (1 | 2Bcst | 2Mlti)> (slot) (interface) (port) on | off Keyword to enable (on) or disable (off) RIP on the specified port.

  • Page 248: Set Mgcp Notified Entity

    port UDP Port number (any valid port number; usually 2427 or 2727) set mgcp Description. Specifies the DNS name or IP address of the notified entity (call agent). You can specify one notified entity in the CLI. Use the menu notified interface to set up a maximum of four call agents.

  • Page 249: Set Mgcp Voice Tos

    Slot number (1 to 7) interface Keyword identifying the interface: ethernet | adsl | xdsl | sdsl port Port number (1 to 8) connection connection Index of this connection number associated with the port (0-7) set mgcp Description. Specifies the TOS byte value for RTP (voice) packets. voice tos set mgcp voice tos <byte value>...

  • Page 250: Set Sdsl Speed

    set sdsl Description. Sets the SDSL speed. This command sets the speed to manual framed (Nokia) or Auto Cycle (Nokia). speed set sdsl speed <speed> <auto | manual> speed Keyword identifying speed: 2320 | 1744 | 1536 | 1152 | 768 | 384 | 192 auto | manual Keyword identifying manual or auto cycle for Nokia.

  • Page 251: Set Wan Atm Vc

    set wan Description. Sets an ATM VC on a given WAN port—RFC 1483 and RFC 2364 VC Muxing PVCs, as well as LLC Encapsulation PVCs. You must atm vc specify VPI number, VCI number and RFC encapsulation type. If you do not enter any optional parameters, it will find the first WAN slot, interface and port.

  • Page 252: Set Wan Datalink

    set wan Description. Sets the datalink protocol to Frame Relay or ATM. If you don’t enter optional parameters, it finds the first available slot, interface datalink and port. set wan datalink <framerelay | atm> (slot) (interface) (port) framerelay | atm Keyword identifying datalink protocol.

  • Page 253: Set Wan Ip Address

    set wan ip Description. Sets the WAN IP address. If you do not enter any optional parameters, it finds the first available slot, interface, port and connection. address set wan ip address <IPaddress> <netmask> (slot) (interface) (port) (connection) IP address IP address in octal format (999.999.999.999) netmask Subnet mask in octal format (255.255.255.255)

  • Page 254: Set Wan Rip

    set wan rip Description. Enables and disables RIP on a WAN IP port. If you do not enter any optional parameters, it will find the first available slot, interface and port. set wan rip <on | off> <version (1, 2Bcst, | 2Mlti)> (slot) (interface) (port) on | off Keyword to enable (on) or disable (off) RIP on the specified port.
  • Page 255 This chapter describes procedures for troubleshooting and diagnosing problems that may be associated with the IAD. Diagnostics are destructive, and may result in loss of connection to network or voice gateway. After running diagnostics, reset the IAD to return to normal working order. This chapter contains the following topics: ‹...

  • Page 256: Using The Diagnostics Menu

    Using the Diagnostic tasks are all displayed and accessed on the Diagnostics menu (displayed by typing Z on the Main menu). Tasks in this chapter are Diagnostics described beginning at the Diagnostics menu. Menu Figure 14–1. Diagnostics Menu ******************************************* ******************************************* P.
  • Page 257 Pots diagnostics are intrusive tests. Any active calls will be terminated. You should terminate all voice gateway activity prior to continuing with any POTS diagnostic testing. The Infineon CODEC test is reserved for Paradyne use only - 238 - February 2004...
  • Page 258 Lines 5 and 6 are connected together Lines 7 and 8 are connected together Hotline test started 6. Press Escape to terminate the test. The IAD terminates the test and displays the POTS Diagnostics menu. Performing a Ring Test The ring test verifies that POTS device attached may be ringed by the IAD. To perform a ring test: 1.
  • Page 259 3. The IAD prompts you to perform the test sequentially or concurrently: Ring lines concurrently or sequentially? (CS or ESC): s Type S to perform the test sequentially, or type C to perform the test concurrently. The IAD displays information about the test progress: Press a key to end ring test...
  • Page 260 Performing an On/Off Hook Test The On/Off Hook test reports the hook state of each voice port line. To perform an On/Off Hook test: 1. Type O on the POTS Diagnostics menu to select On/Off Hook Test. The IAD displays the status of the test as it runs in real time: Display hook state Legend: .=onhook, ^=offhook, #=ring ground, &=no ring ground, *=flash hook...

  • Page 261: Sdsl Diagnostics

    SDSL To perform SDSL diagnostics, type S on the Diagnostics menu. Diagnostics JF2304 JF2308 POWER LAN LINK LAN ACT WAN LINK VOICE The IAD displays the SDSL Diagnostics menu: Figure 14–3. SDSL Diagnostics Menu ******************************************* ******************************************* Select Diagnostic P. Transmit Isolated Pulses 2.

  • Page 262: Isdn-Bri Diagnostics

    ISDN-BRI Type B to perform BRI Diagnostics. Diagnostics JF2004i JF2104i POWER LAN LINK LAN ACT WAN LINK VOICE The IAD displays the BRI Diagnostics menu: Figure 14–4. BRI Diagnostics Menu ************************************************ *********************************************** 0. Select BRI Line 1. Send D Channel Test Pattern 2.

  • Page 263: Troubleshooting The Iad

    Trouble- This section provides information for troubleshooting symptoms associated with the operation of the IAD. shooting probable causes and suggested corrective action to correct the problem. the IAD Table 14–1.Troubleshooting—Symptoms and Causes Symptom Power indicator is not lit. LAN Link indicator is not lit No dial tone is present Incorrect PVC/DLCI 2000-A2-GB20-10...
  • Page 264 Table 14–1.Troubleshooting—Symptoms and Causes Symptom Cannot receive or send data If IAD is configured as router: If the IAD is configured as a bridge: 2000-A2-GB20-10 Probable Cause Corrective Action Incorrect PVC/DLCI Verify these settings: set for data channel VPI: 0 to 255 VCI: 0 to 65535 DLCI: 16 to 1023 (default PVC 0/38;...
  • Page 265 The table following lists the IAD provisioning parameters on the voice gateway that identifies the IAD and affects its performance. Verify these parameters when troubleshooting the IAD. Table 14–2.IAD Provisioning Parameters Parameter Serial Number Profile Name Interface Group ATM Protection Group ATM Protection Group to which the IAD is Transport Signalling Compression...

  • Page 266: Power-Up Test

    This chapter describes how to verify that the JetFusion IAD operates properly after installation. It also covers maintenance and how to display the current configuration. Before you can test the voice capabilities of the JetFusion IAD, you must first provision it at the voice gateway. This chapter contains the following topics: ‹...

  • Page 267: Maintenance

    2. Connect a POTS telephone to a provisioned line port on the IAD. 3. Lift the telephone receiver and check for dial tone If no dial tone is present, troubleshoot as necessary. 4. Repeat steps 2 and 3 for each provisioned line port. 5.
  • Page 268 2. Type C to display the current configuration. For more information, see Current Configuration Report, on page 182. 2000-A2-GB20-10 - 249 - February 2004...

  • Page 269: Menu Map

    Menu Map This appendix provide a map of the menu interface for the JetFusion family of IADs. 1. Reports Menu C. Display Current Config N. Display Network Stats I. Display Interface Stats M. Display Media Stats R. Display Route Table A.
  • Page 270 D.Configure DHCP E. Enable/Disable DHCP H. Enable/Disable Checking for Add'l DHCP Servers B. Enable/Disable DHCP Debug Messages* I. Configure DHCP Server Parameters P. Configure DHCP Address Range Pool C. Configure DHCP Client Entry F. Display DHCP Configuration S. Display DHCP Server Statistics A.

  • Page 271: Country Codes Tables

    Country This appendix specifies the settings for each country code setting supported by the IAD. When you select a specific country mode, the Codes Tables values are set automatically. Table B–1. Country Code Settings—USA, Australia 1 and 2, and Germany Parameters Min.
  • Page 272 Table B–3. Country Code Settings—Belgium2, Denmark, and Italy Parameters Belgium2 Min. Flash Hook (ms) Max. Flash Hook (ms) Ring Frequency (Hz) Receive Gain (dB) Transmit Gain (dB) Ref/Input Impedance 150 + (830 // 72nF) (Ohms) Load Impedance (Ohms) JF2008 JF2104 JF2108 2000-A2-GB20-10 Denmark...

  • Page 273: Equipment List

    This appendix lists the specifications for the JetFusion IAD family. Where a specification to specific IADs, rather than the entire family, it is noted in the IAD or Description column of each specification table. Equipment List Table C–1. JetFusion IAD Part Numbers (1 of 2) Model Description JF2002 ADSL - 2 ports POTS - Other Europe JF2002 ADSL - 2 ports POTS - NA...

  • Page 274: 2/4/8-Port

    Table C–1. JetFusion IAD Part Numbers (2 of 2) Model Description JF2216 T1/E1 - 16 ports POTS - NA JF2224 T1/E1 - 24 ports POTS - NA JF2304 SDSL - 4 ports POTS - NA JF2308 SDSL - 8 ports POTS - NA JF2316 SDSL - 16 ports POTS - NA JF2324 SDSL - 24 ports POTS - NA 2/4/8-Port...
  • Page 275 A-law, u-law G.168 compliant (single reflector) Digital G3, G4 (for JF2004i and JF2104i), and analog V.17, V.29 (with external adapter) CopperCom, ELCP (af-vmoa-0145), Paradyne, LES (af-vmoa-0145), MGCP, SIP capable V.34, V.90 support caller ID, flash hook, three-way calling, distinctive ringing, stutter dial tone, call forwarding, call...
  • Page 276 Table C–5. 2/4/8-Port Data Features Feature LAN Interface Bridging Routing DHCP HDLC Support Management Configuration 2000-A2-GB20-10 Description 10/100 BaseT Ethernet (RJ45) IEEE 802.1d including spanning tree Default, Static, RIP1 (RFC 1058), RIP2 (RFC 2453), IPCP for IP Packet Processing Server, Client (RFC 2131), Relay Agent PPPoA, PAP, CHAP, IPCP (RFC 1332) SNMP (RFC 1157), MIB1, MIB2 (RFC 1213), AAL2/LES MIB, Enterprise MIB...
  • Page 277 Transport 2000-A2-GB20-10 Description RJ45 ANSI T1.413 Issue 2; ITU-T G.992.2, G.992.1 Alcatel, Cisco, Lucent, Nortel CopperCom, Paradyne (Jetstream), TdSoft, Tollbridge. BLES: General Bandwidth, Accelerated. Alcatel MCCP V0.1, NCS 1.0, MGCP 1.0 support Point-to-Point (PPP) RJ45 ANSI T1.413 Issue 2; ITU-T G.992.2, G.992.1 Cisco, Coppermountain, Novae, Lucent, Nokia CopperCom, Paradyne (Jetstream);...
  • Page 278 DSLAMs Voice Gateways Softswitches Protocols 2000-A2-GB20-10 Description Cisco, Coppermountain, Innovia, Lucent, Nokia CopperCom, Paradyne; AAL2/LES: PSAX, TdSoft, Zhone, Tollbridge, General Bandwidth, Accelerated, Alcatel, and any af-vmoa-0145 compliant gateway MCCP V0.1, NCS 1.0 support Point-to-Point (PPP) - 259 - February 2004...
  • Page 279 Table C–7. 2/4/8-Port Transport Protocol Features Feature Adaption Layers Encapsulation AAL2 Profiles Voice Data Security Voice QoS Data QoS Cell Delay Variation Buffer OAM Cell Handling Frame Relay Encapsulation Voice Data Data Link Format Data Link Control Data Internetworking FRF.5, FRF.8 support Framing Table C–8.
  • Page 280 Table C–9. 2/4/8-Port Security Features Feature Firewall Management Security Authentication Table C–10. JF2008, JF2004i, JF2104i and JF2104/8 Interface Power Supply Power Operating Temperature Storage Temperature -10 C to 70 C Operating Humidity Safety Emissions LEDs Physical Dimensions (L X W x H) = 11.8" X 8.3" X 1.8" Weight Mounting Table C–11.
  • Page 281 Table C–11. 2/4/8-Port Network Interfaces (2 of 2) Interface SDSL T1/E1 Voice Ports 16/24-Port 16/24-port IADs share common voice, data, configuration, security and environmental features and specifications. The JF2200 series has a T1 WAN interface, and the JF2300 series has an SDSL WAN interface. Table C–12.
  • Page 282 Description JF2216, JF2224: T1/UNI (RJ45) JF2316, JF2324: SDSL (2B1Q) (RJ45) ITU-T G.992.2, G.992.1 ATM | Frame Relay CopperCom, Paradyne, TdSoft, Tollbridge. BLES: General Bandwidth, Accelerated, Alcatel, Zhone, Lucent MCCP V0.1, NCS 1.0 support Point-to-Point (PPP) AAL2 (voice), AAL5 (data), AAL5 (layer 3 voice) RFC 1483 multiprotocol encapsulation over ATM;...
  • Page 283 Table C–14. 16/24-Port WAN Features (2 of 2) Feature Cell Delay Variation Buffer OAM Cell Handling Frame Relay Encapsulation Voice Data Data Link Format Data Link Control Data Internetworking FRF.5, FRF.8 support Framing 2000-A2-GB20-10 Description Configurable 0-30 ms F4|F5 segment and end-to-end loopbacks RFC 1490 multiprotocol encapsulation over frame relay Single PVC...

  • Page 284: Connector Pinouts

    Connector This appendix specifies pinouts for each connector on the IAD. Pinouts Table D–1. RS-232 DB-9 Console Port Pin Assignments Table D–2. RJ11 POTS Port Pin Assignments Line Table D–3. RJ45 BRI ISDN S0 Port Pin Assignments Line 2000-A2-GB20-10 Signal Ground Tx Data Rx Data...
  • Page 285 Table D–4. 10BaseT Connector Pin Assignments Table D–5. 100BaseT Connector Pin Assignments (RJ48) Table D–6. ADSL/SDSL Connector Pin Assignments (RJ45) Table D–7. G.SHDSL Port Pin Assignments (RJ11) Line 2000-A2-GB20-10 Signal Signal Signal Pin Assignment Line Ring - 266 - Signal Signal Signal Ring...
  • Page 286 Table D–8. T1/E1 Connector Pin Assignments Table D–9. USI Port for RS-530, V.35 and RS-449 Signal Shield Ground Transmit Data (A) Receive Data (A) Request to Send (A) Clear to Send (A) DCE Ready (A) Signal Ground Receive Line Signal (A) Receive DCE Clock (B) Receive Line Signal (B) Transmit DTE Clock (B)

  • Page 287: Glossary

    Glossary 10/100BaseT. 10-Mbps baseband Ethernet specification that uses two pairs of twisted-pair cabling: one pair for transmitting data and the other for receiving data. 10/100BaseT has a distance limit of approximately 100 meters per segment. 100BaseT. 100-Mbps baseband Fast Ethernet specification that uses UTP wiring.
  • Page 288 membership. It is also used by connected routers to discover these group members. Inverse ARP. Inverse Address Resolution Protocol. Enables routers to obtain the IP address of a known Ethernet address of a device associated with a virtual circuit. Method of building dynamic routes in a network. IP.
  • Page 289 The lowest layer is closest to the media technology and the highest layer is closest to the user. The hardware and software implement the lower two layers, while only the software implements the upper five layers. Physical layer—the actual wires and connections in the network. Data link layer—responsible for physical addressing, network topology, error notification and ordered delivery.
  • Page 290 Router. Network layer device that uses one or more metrics to determine the optimal path to forward network traffic. Routers forward packets from one network to another based on network layer information. a router may connect networks using various protocols by encapsulating data within another network’s packet format or by removing layers of packet formatting.
  • Page 291 Numerics 10/100Base-T Ethernet 4, 6 16/24-port family features of 5 front panel 5 generally 4 rear panel 6 telephone interface supported 7 USI port on 20 WAN interfaces supported 6 2/4/8-port family features of 2 front panel 3 IADs described 2 rear panel 4 telephone interfaces 4 voice gateways interoperable with 2, 5...
  • Page 292 setting timeout period 36 contents, described xi conventions, described xiii Copper Mountain 2, 5, 258 Auto Sense in Quick Configuration 95 Auto Sense, setting 61 Auto Sense, setting in SDSL configuration 61 fragmentation, setting 92 supported DSLAM 258 Copper Mountain CMCP setting in Frame Relay options 90 CopperCom 258 CopperCom Call Control menu 142...
  • Page 293 F4 OAM VPI, configuring 85 FCC Notice xiii fers 43 file copying 40 file directory, displaying 39 file system formatting 40 free space, determining 40 using, generally 39 File System menu 39 File Transfer menu 33, 43 File Transfer Method menu 43 file transfers, performing 43 files deleting 40...
  • Page 294 16/24-Port family 4 2/4/8-Port family 2 JetStream call control settings 144 JF2004i connecting ISDN to 20 JF2104i connecting ISDN to 20 JF230x Quick Configuration of 95 jitter delay displaying 130 setting 130 connecting 19 LAN connection setting up 34 LAN IP broadcast destination configuring 116 last reset reason, displaying and clearing 38 Line Build Out menu (E1) 72...
  • Page 295 Speedlink System 2, 5 supported DSLAM 258 Nortel 63 OAM loopback, sending 86 on/off hook test 241 On-hook Transmission mode setting 133 Paradyne 258 call control settings 144 GranDSLAM 2, 5 in Quick Configuration 95 part numbers 254 passwords 11 changing 24...
  • Page 296 reports, list of 181 reset system CLI command 224 reset, performing hard 37 Reverse Path Forwarding 165 RFC 1483 setting in PVC 79 RFC 2364, setting in PVC 80 ring test 239 enabling and disabling 101 enabling globally 101 version, setting 102 RIP Poisoned Reverse enabling and disabling 101 RJ21X...
  • Page 297 system settings, saving 38 system software identifying version 33 System Uptime report 219 switching to 66 T1 configuration flowchart 50 T1 Configuration menu 65, 67 T1 Frame Mode menu 67 T1 interface configuring 66 T1/E1 connecting to IAD 20 TCP Statistics report 190 TDM Voice, setting up channels for 54 TdSoft 258 telephone devices...

This manual is also suitable for:

2000Jetfusion

Table of Contents