Setup Menu Table - MIMAKI TS300P-1800 Operation Manual

SETUP MENU table

• For each setting item below, you can set it so that the machine may operate according to the value specified when you
printed from your RIP software in the connected host PC.
• Set Item : LOGICAL SEEK/ Overprint/ DRYING TIME/ MARGIN (LEFT and RIGHT)/ VACUUM FAN/ FEED SPEED
• When you operate the machine according to the contents specified with the RIP software, set each
• item to "Host" when registering this machine type. When you set it other than "Host", the machine operates according to
the machine setup.
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name
FEED COMP. ( P.3-5)
DROP.POScorrect ( P.3-6)
POST1
HEATER POST2
( P.3-6)
OFF TIME
FAN HEATER
OPTION
STANDBY TIME
HEATER
( P.3-7)
OFF TIME
LOGICAL SEEK ( P.3-7)
Overprint ( P.3-7)
DRYING TIME SCAN
( P.3-8)
PRINT END
MARGIN/LEFT ( P.3-8)
MARGIN/RIGHT ( P.3-8)
VACUUM FAN ( P.3-9)
*2
FEED SPEED ( P.3-9)
FEED QUALITY ( P.3-9)
AUTO MAPS MODE STANDARD/ QUALITY
MAPS4 Pattern
MANU
( P.3-11)
Smoothing
AL
Lv.
OFF, FILE, LENGTH,
TIME
FILE INTERVAL 1 to 1000
TYPE
AUTO LENGT
INTERVAL 0.1 to100.0m
CLEANING H
( P.3-11)
TYPE
TIME INTERVAL 10 to 120 min
TYPE
Cleaning Check
INTERVAL WIPING ( P.3-11)
Pre-feed ( P.3-12)
RESET SETTING ( P.3-5)
*1. This is the setting value to be used for printing when setting value is not specified at the RIP software (host) side, or, you give priority to the setting value at
the machine side.
*2. When you set this to "100%" or more, required time for completion of printing will be shortened. However, enough drying time cannot be ensured and it may
affect the image quality.
When no instruc-
Set value
-9999 to 0 to 9999
-40.0 to 0 to 40.0
20 to 50 °C (68 to 122°F)
20 to 60 °C (68 to 140°F)
NONE/ 0 to 90 min
OFF/ LOW/ MID/ HIGH
none/ 0 to 90 min.
none/ 0 to 90 min.
HOST/ON / OFF
HOST/ 1 to 9
HOST/ 0.0 to 9.9 sec
HOST/ 0 to 120 min
HOST/ -10 to 85mm
HOST/ WEAK/ STANDARD/
STRONG
HOST/ 10 to 200%
HOST/ STANDARD/
QUALITY
1 / 2 / 3
5 to 25 to 100%
NORMAL/ SOFT/ HARD
NORMAL/ SOFT/ HARD
NORMAL/ SOFT/ HARD
ON/ OFF
3 to 255 min, OFF
OFF/ 100 to 500mm
The configulation in the settings 1-4 can be reset ondividually.
tion from RIP
*1
exists
Used to print a pattern for correcting a media-
feeding rate and correct it.
Used to adjust the dot position in go and return
printing.
Sets each heater's conditions.
Set the time from the print completion until the
heater to be OFF.
Sets the heater intensity.
Sets the time required for the intensity to start
dropping to "LOW" after the printing operation is
completed.
Set the time from the print completion until the
heater to be OFF.
OFF Sets the scan movable area during printing.
Sets the number of layers in which ink is to be
OFF
applied.
0 sec
Sets the time to wait for ink drying.
0 min
0 mm Sets a non-printing area along the right and left
edges of the media.
0 mm
STRONG Sets the absorbability of the media.
100 % Changes the media feeding speed in printing.
Change the speed and acceleration to feed a
STANDARD
media during printing.
Perform setting to reduce stripes between passes.
Sets the automatic cleaning operation for the head
performed before printing or during printing.
Set to run or not a nozzle check after auto
cleaning.
Sets the wiping operation performed after printing
is completed.
In order to prevent sticking and wrinkles of the
media, set the media length to feed back and forth
before printing.
Chapter 3 Setup
Outline
3-3
1
2
3
4
5
6