Setup Menu Table - MIMAKI TS500P-3200 Operation Manual

 Screen transition when
When adjustment functions (Feed Comp./ Prop Pos. Correct) are performed, the Adjust menu can be displayed easily without
selecting [MENU]-[Setup] from Local. Press the [SEL] key to display "ADJUST" for [FUNC1], and then press the [FUNC1] key.
12:00
Local <Setup 1>
1340mm
PRINT POST 1L POST 2L POST 1R POST 2R
25° C 34° C 50° C 30° C 32° C
TEST PRINT /
MENU REMOTE
CLEANING

Setup menu table

• For each setting item below, you can set it so that the machine may operate according to the value specified when you
printed from your RIP software in the connected host PC.
• Set Item : DRYING Time/ Vacuum Fan
• When you operate the machine according to the contents specified with the RIP software, set each item to "Host" when
registering this machine type. When you set it other than "Host", the machine operates according to the machine setting.
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name
Feed Comp. ( P.3-6)
Drop Pos. Correct ( P.3-7)
PRINT
POST 1L
Heater POST 2L
( P.3-8)
POST 1R
POST 2R
EXTERNAL HEATER
Logical Seek ( P.3-8)
Overprint ( P.3-9)
Drying Time
Scan
( P.3-19)
Margin/L ( P.3-9)
Margin/R ( P.3-9)
Refresh ( P.3-10)
Refresh Left ( P.3-20)
Vacuum Fan ( P.3-10)
Feed Speed ( P.3-10)
Auto/ Manual
MAPS4
Speed
( P.3-11)
Manual
Smoothing Lv.
(ADJUST) key is pressed
Adjust Adjust
Feed Comp. > Feed Comp.
PropPos. Correct > PropPos. Correct
*1
Set value
-9999 to 0 to 9999
-40.0 to 0 to 40.0
OFF/ 20 to 60 °C
(OFF/ 68 to 140°F)
OFF/ 20 to 60 °C
(OFF/ 68 to 140°F)
OFF/ 20 to 70 °C
(OFF/ 68 to 158°F)
OFF/ 20 to 60 °C
(OFF/ 68 to 140°F)
OFF/ 20 to 70 °C
(OFF/ 68 to 158°F)
ON/OFF
Host / ON/OFF
Host / 1 to 9
Host /0.0 ~ 9.9 sec
Host /-10 to 0 to 85mm
Host / Lv.0 to Lv.3
ON/OFF
Host / OFF/ Weak/
Standard/ Strong
Host / 10 to 200 %
50 to 100 %
0 to 25 to 100%
>
>
When no instruc-
tion from RIP
*2
exists
Used to print a pattern for correcting a media-
feeding rate and correct it.
Used to adjust the dot position in go and return
printing.
Sets the print-heater's temperature.
Set the temperature of the post heater (1/2) on
the left side.
Set the temperature of the post heater (1/2) on
the right side.
Sets ON/OFF of the external heater.
Sets the scan movable area during printing.
Sets the number of layers in which ink is to be
1
applied.
0 sec Sets the drying time of ink per scan.
Sets a non-printing area along the right and
left edges of the media.
Sets the interval of refresh performed during
Lv.3
printing.
Depending on the type of ink to be used, if the
flushing operation on the capping station can
OFF
not fully refresh the head, you can also set to
allow the flushing operation on the left side.
Standard Sets the absorbability of the media.
Changes the media feeding speed in printing.
Perform setting to reduce stripes between
passes.
Chapter 3 Setup
Outline
3-3
3
2
2