Setup Menu Table - MIMAKI TS55-1800 Operation Manual

SETUP MENU table

• For each setting item below, you can set it so that the machine may operate according to the value specified when you
printed from your RIP software in the connected host PC.
• Set Item : LOGICAL SEEK/ Overprint/ DRYING TIME/ MARGIN (LEFT and RIGHT)/ VACUUM FAN/ FEED SPEED
• When you operate the machine according to the contents specified with the RIP software, set each
• item to "Host" when registering this machine type. When you set it other than "Host", the machine operates according to
the machine setup.
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name
FEED COMP.
( P.3-4)
Each Print Cond.
( P.3-5)
DROP.POScorrect ( P.3-5)
POST1
HEATER POST2
( P.3-6)
OFF TIME
LOGICAL SEEK ( P.3-6)
Overprint ( P.3-6)
SCAN
DRYING TIME
( P.3-7)
PRINT END
MARGIN/LEFT ( P.3-7)
MARGIN/RIGHT ( P.3-7)
VACUUM ( P.3-7)
*2
FEED SPEED ( P.3-8)
OFF, FILE, LENGTH,
TIME
FILE INTERVAL 1 to 1000
TYPE
AUTO
LENGTH INTERVAL 0.1 to100.0m
CLEANING
TYPE
( P.3-8)
TIME INTERVAL 10 to 120 min
TYPE
Cleaning Check
EXTERNAL HEATER ( P.3-9)
AUTO MAPS MODE STANDARD/ QUALITY
MAPS4 SPEED
MANU
( P.3-9)
Smoothing
AL
Lv.
Pass density correct ( P.3-10)
Pre-feed ( P.3-10)
RESET SETTING ( P.3-4)
*1. This is the setting value to be used for printing when setting value is not specified at the RIP software (host) side, or, you give priority to the setting value at
the machine side.
*2. When you set this to "100%" or more, required time for completion of printing will be shortened. However, enough drying time cannot be ensured and it may
affect the image quality.
When no instruc-
Set value
-9999 to 0 to 9999
ON/ OFF
-255 to 0 to 255
-40.0 to 0 to 40.0
20 to 50 °C (68 to 122°F)/OFF
20 to 60 °C (68 to 140°F)/OFF
NONE/ 0 to 90 min
HOST/ON / OFF
HOST/ 1 to 9
HOST/ 0.0 to 9.9 sec
HOST/ 0 to 120 min
HOST/ -10 to 85 mm
HOST/ WEAK/ STANDARD/
STRONG
HOST/ 10 to 200%
NORMAL/ SOFT/ HARD
NORMAL/ SOFT/ HARD
NORMAL/ SOFT/ HARD
ON/ OFF
ON/ OFF
50 to 100%
0 to 25 to 100%
OFF / Lv0 to Lv3 to Lv8
OFF / 100 to 500 mm
The configuration in the settings 1-4 can be reset individually.
tion from RIP
*1
exists
Used to print a pattern for correcting a media-
feeding rate and correct it.
You can perform feed correction and apply
correction values for each print mode having
different feed conditions.
Used to adjust the dot position in go and return
printing.
Sets each heater's conditions.
Set the time from the print completion until the
heater to be OFF.
OFF Sets the scan movable area during printing.
Sets the number of layers in which ink is to be
1
applied.
0 sec
Sets the time to wait for ink drying.
0 min
0 mm
Sets a non-printing area along the right and left
edges of the media.
0 mm
WEAK Sets the absorbability of the media.
100% Changes the media feeding speed in printing.
Sets the automatic cleaning operation for the head
performed before printing or during printing.
Set to run or not a nozzle check after auto
cleaning.
Used to set external heater to ON/OFF.
Perform setting to reduce stripes between passes.
If periodic pass density differences are noticeable
between passes, it can be reduced by changing
this setting.
In order to prevent sticking and wrinkles of the
media, set the media length to feed back and forth
before printing.
Chapter 3 Setup
Outline
3-3
1
2
3
4
5
6