Setup Menu Table - MIMAKI Tx300P-1800 Operation Manual

SETUP MENU table

• For each setting item below, you can set it so that the machine may operate according to the value specified when you
printed from your RIP software in the connected host PC.
• Set Item : LOGICAL SEEK/ Overprint/ DRYING TIME/ MARGIN (LEFT and RIGHT)/ FEED SPEED
• When you operate the machine according to the contents specified with the RIP software, set each
• item to "Host" when registering this machine type. When you set it other than "Host", the machine operates according to
the machine setup.
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name
FEED COMP. ( P.3-6)
DROP.POScorrect ( P.3-7)
LOGICAL SEEK ( P.3-7)
Overprint ( P.3-8)
SCAN
DRYING TIME
( P.3-8)
PRINT END
MARGIN/LEFT ( P.3-8)
MARGIN/RIGHT ( P.3-8)
VACUUM
(Tx300P-1800 MkII Only)
*2
FEED SPEED ( P.3-9)
DEFAULT, FILE,
LENGTH, TIME
DEFAULT
FILE INTERVAL 1 to 1000
AUTO
TYPE
CLEANING
LENGTH INTERVAL 0.1 to 100.0 m
( P.3-10)
TYPE
TIME INTERVAL 10 to 480 min
TYPE
Cleaning Check
EXEC.TIMING
INTERVAL WIPING ( P.3-11)
EXTERNAL HEATER ( P.3-11)
AUTO
MAPS4 SPEED
MANU
( P.3-9)
Smoothing
AL
Lv.
RESET SETTING ( P.3-5)
*1. This is the setting value to be used for printing when setting value is not specified at the RIP software (host) side, or, you give priority to the setting value at
the machine side.
*2. When you set this to "100%" or more, required time for completion of printing will be shortened. However, enough drying time cannot be ensured and it may
affect the image quality.
When no instruc-
Set value
-9999 to 0 to 9999
-40.0 to 0 to 40.0
HOST/ ON / OFF
HOST/ 1 to 9
HOST/ 0.0 to 9.9 sec
HOST/ 0 to 120 min
HOST/ -10 to 85 mm
OST/ WEAK/ STANDARD/
STRONG
HOST/ 10 to 200%
The value differs depending
on the type of ink to be used
and the operating
environment.
NORMAL/ SOFT/ HARD
NORMAL/ SOFT/ HARD
NORMAL/ SOFT/ HARD
ON/ OFF
END OF FILE/PRINTING
3 to 255 min, OFF
ON/ OFF
50 to 100%
0 to 25 to 100%
The configuration in the settings 1-4 can be reset individually.
tion from RIP
*1
exists
Used to print a pattern for correcting a media-
feeding rate and correct it.
Used to adjust the dot position in go and return
printing.
OFF Sets the scan movable area during printing.
Sets the number of layers in which ink is to be
1
applied.
0 sec
Sets the time to wait for ink drying.
0 min
0 mm
Sets a non-printing area along the right and left
edges of the media.
0 mm
STRONG Sets the absorbability of the media.
100% Changes the media feeding speed in printing.
Sets the automatic cleaning operation for the head
performed before printing or during printing.
Set to run or not a nozzle check after auto
cleaning.
Sets the timing for cleaning operation performed
when "LENGTH" or "TIME" is selected.
Sets the wiping operation performed after printing
is completed.
Used to set external heater to ON/OFF
Perform setting to reduce stripes between passes.
Chapter 3 Setup
Outline
3-3
1
2
3
4
5
6