D-Link DGS-1510/ME Series Reference Manual page 82

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
<netmask> - Enter the source netmask used here.
destination_ip - (Optional) Specifies an IP destination address.
<ipaddr> - Enter the destination IP address used for this configuration here.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<netmask> - Enter the destination netmask used here.
dscp - (Optional) Specifies the value of DSCP. The DSCP value ranges from 0 to 63.
<value 0-63> - Enter the DSCP value here.
icmp - (Optional) Specifies to configure the ICMP parameters.
type - (Optional) Specifies that the rule will apply to the ICMP Type traffic value.
<value 0-255> - Enter the ICMP type traffic value here. This value must be between 0 and 255.
code - (Optional) Specifies that the rule will apply to the ICMP Code traffic value.
<value 0-255> - Enter the ICMP code traffic value here. This value must be between 0 and 255.
igmp - (Optional) Specifies to configure the IGMP parameters.
type - (Optional) Specifies that the rule will apply to the IGMP Type traffic value.
<value 0-255> - Enter the IGMP type traffic value here. This value must be between 0 and 255.
tcp - Specifies to configure the TCP parameters.
src_port - (Optional) Specifies that the rule will apply to a range of TCP source ports.
<value 0-65535> - Enter the TCP source port value here. This value must be between 0 and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the source port mask here.
dst_port - (Optional) Specifies that the rule will apply to a range of TCP destination ports.
<value 0-65535> - Enter the TCP destination port value here. This value must be between 0 and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the destination port mask here.
flag - (Optional) Specifies the TCP flag fields.
all - Specifies that all the TCP flags will be used in this configuration.
urg - (Optional) Specifies that the TCP flag field will be set to 'urg'.
ack - (Optional) Specifies that the TCP flag field will be set to 'ack'.
psh - (Optional) Specifies that the TCP flag field will be set to 'psh'.
rst - (Optional) Specifies that the TCP flag field will be set to 'rst'.
syn - (Optional) Specifies that the TCP flag field will be set to 'syn'.
fin - (Optional) Specifies that the TCP flag field will be set to 'fin'.
udp - Specifies to configure the UDP parameters.
src_port - (Optional) Specifies the UDP source port range.
<value 0-65535> - Enter the UDP source port value here. This value must be between 0 and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the source port mask here.
dst_port - (Optional) Specifies the UDP destination port range.
<value 0-65535> - Enter the UDP destination port value here. This value must be between 0 and
65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the destination port mask here.
protocol_id - Specifies that the rule will apply to the value of IP protocol ID traffic.
<value 0-255> - Enter the protocol ID used here.
user_define - (Optional) Specifies that the rule will apply to the IP protocol ID and that the mask options
behind the first 4 bytes of the IP payload.
<hex 0x0-0xffffffff> - Enter the user-defined mask value here.
mask - Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffffffff> - Enter the mask value here.
packet_content - Specifies the offset. Each offset defines 4 bytes of data which is identified as a single UDF
78