Mitsubishi Electric FR-F800 Series Instruction Manual page 557

• An excitation current low-speed scaling factor set in the parameter shown in the table is used according to the Pr.14 setting
and other conditions.
Pr.14 setting
0, 1
12
13
14
15
• When the SF-PR/SF-HR/SF-HRCA motor is used (Pr.71 = "40, 43, 44, 50, 53, 54, 70, 73, or 74") and "9999" is set in Pr.85/
Pr.86, the predetermined setting in the following table is applied.
Motor
capacity Pr.81 = "2"
(kW)
Pr.85
0.4 —
0.75 20 Hz
1.5 30 Hz
2.2 10 Hz
3.7 30 Hz
5.5 10 Hz
7.5 10 Hz
11 10 Hz
15 10 Hz
18.5 10 Hz
22 30 Hz
30 10 Hz
37 20 Hz
45 10 Hz
55 20 Hz
556
5. PARAMETERS
5.13 (G) Control parameters
Downloaded from ManualsNet.com
During forward rotation
RT signal OFF RT signal ON
Pr.86 Pr.566
Pr.86 Pr.566
Pr.617 Pr.617
Pr.86 Pr.566
Pr.617 Pr.566
SF-PR
Pr.81 = "4"
Pr.86 Pr.85 Pr.86
— — —
130% 20 Hz 130%
140% 10 Hz 130%
150% 10 Hz 130%
150% 25 Hz 133%
150% 10 Hz 130%
150% 30 Hz 118%
150% 20 Hz 140%
150% 30 Hz 130%
150% 30 Hz 130%
130% 10 Hz 130%
150% 20 Hz 130%
140% 10 Hz 140%
140% 20 Hz 130%
140% 30 Hz 130%
search engine
During reverse rotation
RT signal OFF
Pr.86
Pr.617
Pr.86
Pr.617
Pr.86
Pr.81 = "6" Pr.81 = "2"
Pr.85 Pr.86 Pr.85
— — 10 Hz 130%
10 Hz 130% 10 Hz 130%
10 Hz 130% 10 Hz 130%
20 Hz 130% 20 Hz 150%
20 Hz 130% 30 Hz 160%
30 Hz 130% 30 Hz 140%
30 Hz 130% 30 Hz 140%
10 Hz 130% 30 Hz 140%
30 Hz 130% 20 Hz 140%
20 Hz 130% 30 Hz 150%
10 Hz 130% 30 Hz 150%
10 Hz 130% 30 Hz 150%
20 Hz 130% 20 Hz 160%
10 Hz 130% 10 Hz 130%
— — 10 Hz 140%
RT signal ON
Pr.566
Pr.617
Pr.566
Pr.566
Pr.566
SF-HR/SF-HRCA
Pr.81 = "4"
Pr.86 Pr.85 Pr.86 Pr.85
10 Hz 130% 10 Hz
10 Hz 130% 10 Hz
10 Hz 130% 10 Hz
10 Hz 130% 10 Hz
30 Hz 140% 10 Hz
30 Hz 140% 20 Hz
30 Hz 140% 30 Hz
10 Hz 130% 30 Hz
10 Hz 130% 30 Hz
30 Hz 140% 30 Hz
30 Hz 140% 20 Hz
20 Hz 150% 10 Hz
20 Hz 150% 10 Hz
20 Hz 140% 10 Hz
20 Hz 150% —
Pr.81 = "6"
Pr.86
130%
130%
130%
130%
130%
140%
150%
130%
130%
140%
140%
130%
130%
140%
—