Mitsubishi Electric FR-F800 Series Instruction Manual page 332

 Output signal list
• A function listed below can be set to each output terminal.
• Refer to the following table and set the parameters. (0 to 99, 200 to 299: Positive logic, 100 to 199, 300 to 399: Negative
logic)
Setting
Positive Negative
logic logic
0 100
1 101
2 102
3 103
4 104
5 105
7 107
8 108
10 110
11 111
12 112
13 113
14 114
15 115
16 116
17 —
18 —
19 —
25 125
26 126
35 135
39 139
40 140
41 141
42 142
Downloaded from ManualsNet.com
Signal
Function
name
RUN Inverter running
*1
SU
Up to frequency
Instantaneous power failure/
IPF
*2
undervoltage
OL Overload warning
FU Output frequency detection
Second output frequency
FU2
detection
For manufacturer setting. Do not set.
Electronic thermal O/L relay
THP
pre-alarm
PU PU operation mode
RY Inverter operation ready
Y12 Output current detection
Y13 Zero current detection
FDN PID lower limit
FUP PID upper limit
PID forward/reverse rotation
RL
output
MC1 Electronic bypass MC1
MC2 Electronic bypass MC2
MC3 Electronic bypass MC3
FAN Fan fault output
FIN Heat sink overheat pre-alarm
TU Torque detection
Y39 Start time tuning completion
Y40 Trace status
FB Speed detection
FB2 Second speed detection
search engine
Operation
Output during operation when the inverter
output frequency reaches Pr.13 Starting
frequency or higher.
Output when the output frequency reaches
the set frequency.
Output when an instantaneous power failure
or undervoltage protection operation occurs.
Output while the stall prevention function
works.
Output when the output frequency reaches
the frequency set in Pr.42 (Pr.43 during
reverse rotation) or higher.
Output when the output frequency reaches
the frequency set in Pr.50 or higher.
Output when the cumulative electronic
thermal O/L relay value reaches 85% of the
trip level. (The electronic thermal O/L relay
function (E.THT/E.THM) is activated when
the value reaches 100%.)
Output when PU operation mode is selected. Pr.79
Output when the reset process is completed
after powering ON the inverter or when the
inverter is ready to start operation with the
start signal ON or during operation.
Output when the output current is higher than
the Pr.150 setting for the time set in Pr.151 or
longer.
Output when the output current is lower than
the Pr.152 setting for the time set in Pr.153 or
longer.
Output when the input value is lower than the
lower limit set for the PID control operation.
Output when the input value is higher than
the upper limit set for the PID control
operation.
Output during forward rotation operation in
the PID control operation.
Used to work the electronic bypass function.
Output when a fan fault occurs.
Output when the heat sink temperature rises
to 85% of temperature at which the protective
function of the Heat sink overheat is
activated.
Output when the motor torque is higher than
the Pr.864 setting.
Output when tuning at start-up is completed. Pr.95, Pr.574
Output during trace operation.
Output when the actual motor rotations per
minute (estimate) reaches the setting of
Pr.42 (Pr.50).
5.8 (M) Item and output signal for monitoring
1
2
Refer
Related
to
parameter
3
page
— 335
4
Pr.41 337
466,
Pr.57
472
5
Pr.22, Pr.23,
Pr.66, Pr.148, 290
Pr.149, Pr.154
6
Pr.42, Pr.43 337
Pr.50 337
7
Pr.9 266
8
240
9
— 335
10
Pr.150, Pr.151 339
Pr.152, Pr.153 339
Pr.127 to Pr.134,
Pr.575 to Pr.577, 419
Pr.1346, Pr.1370
Pr.135 to Pr.139,
404
Pr.159
Pr.244 273
— 602
Pr.864 341
400
Pr.1020 to
486
Pr.1047
Pr.42, Pr.50 337
331
5. PARAMETERS