Mitsubishi Electric FR-F800 Series Instruction Manual page 307

 Monitor item list (Pr.52, Pr.774 to Pr.776, Pr.992)
• Use Pr.52, Pr.774 to Pr.776, or Pr.992 to select the item to monitor on the operation panel or the parameter unit.
• Refer to the following table to find the setting value for each monitoring. The value in the Pr. setting column is set in each
of the parameters for monitoring (Pr.52, Pr.774 to Pr.776, and Pr.992) to determine the monitored item. The value in the
RS-485 column is used for the RS-485 communication special monitor selection. The value in the MODBUS RTU column
is used for the MODBUS RTU real time monitor. (The items marked with "—" cannot be selected. The circle in the negative
indication (-) column indicates that the indication of negative signed numbers is available.)
Monitor item
Output frequency
*17
(speed)
*7*9*17
Output current
*7*17
Output voltage
Fault indication
Set frequency / motor
speed setting
Operation speed
Motor torque
Converter output
*7
voltage
—
Electronic thermal O/
L relay load factor
Output current peak
*7
value
Converter output
*7
voltage peak value
Input power
*9
Output power
Load meter
Motor excitation
*7
current
Cumulative
*3
energization time
Actual operation
*3*4
time
Motor load factor
*7
Cumulative energy
Motor output
Trace status
306
5. PARAMETERS
5.8 (M) Item and output signal for monitoring
Downloaded from ManualsNet.com
Increment Pr.
RS-485
and unit setting
*16
1/0/100 H01
0.01 Hz
*6
2/0/100 H02
0.01/0.1 A
0.1 V 3/0/100 H03
— 0/100 —
*16 *2
H05
0.01 Hz 5
*2
1 (r/min) H06
6
*2
0.1% H07
7
*2
0.1 V H08
8
*8
— H09
9
*2
0.1% H0A
10
*6 *2
H0B
0.01/0.1 A 11
*2
0.1 V H0C
12
*6 *2
H0D
0.01/0.1 kW 13
*6 *2
H0E
0.01/0.1 kW 14
0.1% 17 H11
*6
18 H12
0.01 A/0.1 A
1 h 20 H14
1 h 23 H17
0.1% 24 H18
0.01/0.1
25 H19
*5*6
kWh
*6
34 H22
0.01/0.1 kW
1 38 H26
search engine
Negative
MODBUS
indication
RTU
*1
(-)
*19
40201 The inverter output frequency is displayed.
○
40202 The inverter output current effective value is displayed.
40203 The inverter output voltage is displayed.
— Each of the last 8 faults is displayed individually.
40205 The set frequency is displayed.
The motor speed is displayed (depending on the settings
*19
40206
○
of Pr.37 and Pr.144). (Refer to
The motor torque is displayed as a percentage (0%
40207 ○ under V/F control), considering the rated torque as
100%.
40208 The DC bus voltage value is displayed.
40209 For manufacturer setting. Do not set.
The motor thermal cumulative value is displayed,
40210
considering the thermal operation level as 100%.
The peak value of output current, which is constantly
40211 stored, is displayed. (It is reset with every startup of the
inverter.)
The DC bus voltage peak value, which is constantly
40212 stored, is displayed. (It is reset with every startup of the
inverter.)
40213 The power at the inverter input side is displayed.
40214 The power at the inverter output side is displayed.
Torque current is displayed as a percentage, considering
40217
Pr.56 setting value as 100%.
40218 The motor excitation current is displayed.
The cumulative operation time is displayed.
The number of times an integrated value has reached the
40220
maximum value of 65535 hours can be checked in
Pr.563.
The cumulative operation time is displayed.
The number of times an integrated value has reached the
40223 maximum value of 65535 hours can be checked in
Pr.564.
Use Pr.171 to reset it. (Refer to
The output current value is displayed as a percentage,
considering the inverter rated current value as 100%.
40224
Readout (%) = present output current value / inverter
rated current value × 100
The cumulative energy based on the monitored output
40225 power is displayed.
Use Pr.170 to reset it. (Refer to
The output of a machine connected to the motor shaft is
40234 displayed. It is determined by multiplying the present
output torque with the present motor speed.
40238 The trace status is displayed. (Refer to
Description
page 303.)
page 312.)
page 311.)
page 486.)