Mitsubishi Electric FR-F800 Series Instruction Manual page 540

Object Identifier
310
311
312
320
321
322
398
399
10007
10008
*1 R: Read only, W: Read/Write (Commandable values not supported), C: Read/Write (Commandable values supported)
Values written to the objects that support the commandable values are stored in the Priority Array, even when "Write Access Denied" is returned
due to inconsistency of the writing requirements such as the operating mode, on condition that the values are written within the setting range.
*2 If communication speed command source is other than NET, the setting value can be written, but not to be applied.
*3 When both C42 (Pr.1136) and C44 (Pr.1138) ≠ "9999", the setting range is from the smaller coefficient to the larger coefficient of C42 (Pr.1136)
and C44 (Pr.1138). Depending on the setting, the writing value and the reading value may not be the same at the minimum digit.
• BINARY INPUT
Object Identifier
0
1
2
3
4
5
6
7
8
9
10
11
100
101
102
103
104
105
106
107
*1 R: Read only, W: Read/Write (Commandable values not supported), C: Read/Write (Commandable values supported)
Downloaded from ManualsNet.com
Present Value
Object Name
Access Type
PID set point
C
*2
CMD
PID measured
C
*2
value CMD
PID deviation
C
*2
CMD
Second PID set
C
point CMD
Second PID
measured value C
CMD
Second PID
C
deviation CMD
Mailbox
W
parameter
Mailbox value W
Acceleration time W
Deceleration time W
Present Value
Object Name
Access Type
Terminal STF R
Terminal STR R
Terminal AU R
Terminal RT R
Terminal RL R
Terminal RM R
Terminal RH R
Terminal JOG R
Terminal MRS R
Terminal STOP R
Terminal RES R
Terminal CS R
Terminal RUN R
Terminal SU R
Terminal IPF R
Terminal OL R
Terminal FU R
Terminal ABC1 R
Terminal ABC2 R
Terminal So (SO) R
search engine
Description
*1
Set the PID action set point.
This object is the set point during PID operation if Pr.128 = "60 or
61". (Setting range: 0.00 to 100.00)
Set the PID measured value.
This object is the measured value during PID operation if Pr.128 =
"60 or 61". (Setting range: 0.00 to 100.00)
Set the PID deviation. (0.01 increments)
This object is the deviation during PID operation if Pr.128 = "50 or
51". (Setting range: -100.00 to 100.00)
Set the second PID action set point.
This object is the set point during PID operation if Pr.753 = "60 or
61". (Setting range: 0.00 to 100.00)
Set the second PID measured value.
This object is the measured value during PID operation if Pr.753 =
"60 or 61".
(Setting range: 0.00 to 100.00)
Set the second PID deviation. (0.01 increments)
This object is the deviation during PID operation if Pr.753 = "50 or
51". (Setting range: -100.00 to 100.00)
Access to the properties which are not defined as objects are
available. (Refer to page 541.)
Set Pr.7 Acceleration time.
Set Pr.8 Deceleration time.
*1
Represents actual input of terminal STF.
Represents actual input of terminal STR.
Represents actual input of terminal AU.
Represents actual input of terminal RT.
Represents actual input of terminal RL.
Represents actual input of terminal RM.
Represents actual input of terminal RH.
Represents actual input of terminal JOG.
Represents actual input of terminal MRS.
Represents actual input of terminal STOP.
Represents actual input of terminal RES.
Represents actual input of terminal CS.
Represents actual output of terminal RUN.
Represents actual output of terminal SU.
Represents actual output of terminal IPF.
Represents actual output of terminal OL.
Represents actual output of terminal FU.
Represents actual output of terminal ABC1.
Represents actual output of terminal ABC2.
Represents actual output of terminal So (SO).
*3
*3
*3
*3
Description
(0: Inactive, 1: Active)
5. PARAMETERS
5.12 (N) Communication operation parameters
Unit
1
no-units
(95)
2
no-units
(95)
3
percent
(98)
no-units
4
(95)
no-units
5
(95)
percent
6
(98)
no-units
(95)
7
no-units
(95)
seconds
(73)
8
seconds
(73)
9
10
539