Table of Contents
Advertisement
Checking Side 1 Side Edge Registration
1.
Make the following selections:
a.
Select Tray 1, if not already selected.
b.
Select Side 1.
c.
Select 5 for Print Count, if not already selected.
2.
Click Print.
3.
Label each printed sheet with the number of the print (1 through 5), the words "Tray 1"
and "Side 1," and the location of the Lead Edge of each sheet.
4.
Take the third print and measure from the top edge to point B1 (as shown on
Point B1 is at the intersection of the first line from the side edge and the line from the lead
edge.
5.
If the measured value is not 8.5 +/- 1.7mm, perform the Adjustment. If the Check is OK,
repeat steps 2 through 4 for Trays 2 - 5 (specification for Tray 5 is 8.5+/- 2.9mm).
6.
After all trays are set, proceed to
Checking Side 2 Side Edge
Checking Side 2 Side Edge Registration
NOTE: The grid pattern for side 1 does not align with the side 2 grid pattern; do not attempt to
set registration by aligning the grids.
1.
Make the following selections:
a.
Select Tray 1, if not already selected.
b.
Select Side 2.
c.
Select 5 for Print Count, if not already selected.
2.
Click Print.
NOTE: "Side 2" will be delivered face-down in the tray, with the Lead edge to the right and the
side edge to be checked towards you.
3.
Label each printed sheet with the number of the print (1 through 5), the words "Tray 1"
and "Side 2," and the location of the Lead Edge of each sheet.
4.
Take the third print and measure from the lead edge to point B1 (as shown on
Point B1 is at the intersection of the first line from the side edge and the line from the lead
edge.
5.
If the measured value is not 8.5 +/- 1.7mm, perform the Adjustment. If the Check is OK,
repeat steps 2 through 4 for Trays 2 - 5 (specification for Tray 5 is 8.5+/- 2.9mm).
Adjustment
1.
Determine the distance and direction the line needs to move:
•
Lead Reg. Adjustment Step: 0.100 mm/step
Side Reg. Adjustment Step: 0.106 mm/step
•
With the print in the orientation shown in
The Up arrow moves the grid to the left; the Down arrow moves the grid to the right.
The Right arrow moves the grid up; the Left arrow moves the grid down.
2.
Enter the correction and press Adjust one time.
3.
Click Print.
4.
Repeat the Check and Adjustment until registration is within specification.
Initial Issue
WorkCentre 5335 Family Service Documentation
Figure
1).
Registration.
Figure
1).
Figure
1:
07/2011
4-211
BUS Updated 12/2011
ADJ 9.11 Edge Erase Value Adjustment
Purpose
To correct both sides and Lead Edge (Rear/Front) erase values of the image.
NOTE: Before doing this adjustment, the IOT Lead Edge/Side Edge Registration must be
adjusted to specification.
Check
1.
Specify a Tray loaded with paper. Make a black copy without using any originals and leav-
ing the Platen Cover open.
2.
Check that the white area at the lead edge is 4mm wide and those at the both side edges
and the trail edge are 2mm wide.
Adjustment
1.
Enter the diagnostic mode
(Accessing UI
2.
Adjust the NVM value until the measured erase values are 4mm at the lead edge and
2mm at the sides and the end.
Increasing the set value leads to a larger erase amount.
Table 1 NVM List
NVM location Name
767-057
Lead Image Loss Amount
767-058
Side Image Loss Amount
767-059
End Image Loss Amount
3.
Repeat the Check and Adjustment until the Edge Erase is within specification
Diagnostics) and execute
NVM
Read/Write.
Min.
Initial
Max
Step
0
20
40
0.1mm
0
20
40
0.1mm
0
20
40
0.1mm
Repairs & Adjustments
ADJ 9.10, ADJ 9.11
Advertisement
Table of Contents
