Dodge 2000 DURANGO Service Manual page 14

0 - 2 LUBRICATION AND MAINTENANCE
SERVICE PROCEDURES (Continued)
Fig. 2 API Symbol
GEAR LUBRICANTS
SAE ratings also apply to multiple grade gear
lubricants. In addition, API classification defines the
lubricants usage.
LUBRICANTS AND GREASES
Lubricating grease is rated for quality and usage
by the NLGI. All approved products have the NLGI
symbol (Fig. 3) on the label. At the bottom NLGI
symbol is the usage and quality identification letters.
Wheel bearing lubricant is identified by the letter
"G". Chassis lubricant is identified by the latter "L".
The letter following the usage letter indicates the
quality of the lubricant. The following symbols indi-
cate the highest quality.
Fig. 3 NLGI Symbol
1 – WHEEL BEARINGS
2 – CHASSIS LUBRICATION
3 – CHASSIS AND WHEEL BEARINGS
SPECIALIZED LUBRICANTS AND OILS
Some maintenance or repair procedures may
require the use of specialized lubricants or oils. Con-
sult the appropriate sections in this manual for the
correct application of these lubricants.
FLUID CAPACITIES
Fuel Tank
All . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 L (25 gal.)
Engine Oil W/Filter change
4.7 L . . . . . . . . . . . . . . . . . . . . . . . . . 5.7L (6.0 qts.)
5.2L . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 L (5.0 qts.)
5.9L . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 L (5.0 qts.)
Cooling System
4.7L . . . . . . . . . . . . . . . . . . . . . . . . . . . 16L (17qts.)
5.2L . . . . . . . . . . . . . . . . . . . . . . . 13.6 L (14.3 qts.)
5.9L . . . . . . . . . . . . . . . . . . . . . . . 13.6 L (14.3 qts.)
Automatic Transmission
Dry fill capacity. *
42RE, 44RE & 46RE . . . . . . . 9.1-9.5 L (19-20 pts.)
45RFE . . . . . . . . . . . . . . . . . . . . 13.33 L (28.0 pts.)
* Depending on type and size of internal cooler,
length and inside diameter of cooler lines, or use of
an auxiliary cooler, these figures may vary. Refer to
Group 21, Transmission for proper fluid fill proce-
dure.
Transfer Case
NV231 . . . . . . . . . . . . . . . . . . . . . . . 1.2 L (2.5 pts.)
NV231–HD . . . . . . . . . . . . . . . . . . . 1.2 L (2.5 pts.)
NV242 . . . . . . . . . . . . . . . . . . . . . . . 1.4 L (3.0 pts.)
Front Axle
Model 194–FIA . . . . . . . . . . . . . . . . 1.4 L (3.0 pts.)
Rear Axle
8-1/4 in. . . . . . . . . . . . . . . . . . . . . . 2.1 L (4.4 pts.)*
9-1/4 in. . . . . . . . . . . . . . . . . . . . . . 2.3 L (4.9 pts.)*
* Include 0.05 L (0.25 pts.) friction modifier for
limited slip axles.
Power Steering
Power steering fluid capacities are dependent on
engine/chassis options as well as steering gear/cooler
options. Depending on type and size of internal
cooler, length and inside diameter of cooler lines, or
use of an auxiliary cooler, these capacities may vary.
Refer to Section 19 of the service manual for proper
fill and bleed procedures.
DN